Search Documents

By Tibor Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyllite, actinolite-tremolite, cummingtonite-grunerite, and riebeckite. Asbestos and asbestiformm fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestifarm fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so-called asbestos minerals do not have these properties and are not carcinogenic (1, 2).

Jan 1, 1989

By S. M. Hay

The zinc content of blast furnace and basic oxygen furnace dusts is low compared with electric arc furnace dusts and it is generally not economical to treat the dusts to recover zinc. However, they have a high iron content and removal of the zinc would allow recovery of the iron values. A literature review and thermodynamic analysis was undertaken and, as a result, several smelting options were identified. This paper describes experiments undertaken to develop understanding of metallurgical aspects of these processes which are not amenable to theoretical analysis. Dusts from an Australian steelworks were characterised in order to determine their mineralogical make-up and the form of the iron. The processing aspects investigated in the laboratory were slag-metal equilibrium and solid-state pre-reduction using reducing gases of compositions expected from bath-smelting processes. Particular attention. was paid to the deportment of zinc, sodium, potassium, phosphorous and sulfur between the phases formed during smelting and pre-reduction. The smelting results indicate that less than 10% of the zinc, sulphur, sodium and potassium report to the metal. About 99% of the zinc and potassium and about 80% of the sodium could be volatilised from the dusts by reducing them at 1,000°C with mixtures of CO, CO2, H2 and H2O even when metallic iron was not formed. The experiments indicate that smelting of blast furnace and basic oxygen furnace dusts should produce hot-metal of a composition which can be blended into the main stream of hot-metal in the steelworks.

Jan 1, 1994

By Donna L. Bodine

The ability of oxidized Upper Freeport bituminous coal to adsorb Cu2+, Cd2+ and Mn(VII) from very dilute aqueous solutions has been studied. Low-rank coal is known to adsorb heavy metal ions from dilute, aqueous solutions, probably by ion exchange and/or chelation by acidic functional groups on the coal surface. However, it would be advantageous to use higher rank coals for water treatment. Coal samples were oxidized thermally or by 30% H202 to increase the surface concentration of phenolic and carboxylic groups, then portions were shaken with Cu2+ and Cd2+ solutions. Acidic KMnO4 was also used to oxidize coal, with concurrent sorption of the resulting Mn(IV) and Mn(ll). The effect of oxidation treatment, metal ion concentration, and solution pH on metal uptake kinetics was investigated. Potential applications for treating effluents, especially those containing oxidizing ions, are discussed, along with possible flowsheet options.

Jan 1, 1995

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800' C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By Du Sichen, S. Seetharaman, Wei Liu

"The viscosities of two-phase mixtures are of great importance in the modelling of the fluid flow in metallurgical processes. For example, in steel making and refining, the intimate mixing of metal droplets in the slag phase requires a consideration of the effective viscosities for the mixture. The present work was aimed at an understanding the phenomena underlying the viscous flow in a two-phase mixture with widely differing viscosities.Emulsions of silicone oils of known viscosities (345mPa.S and 1010mPa.S at 293K) with small amounts of water evenly distributed in the same were prepared by subjecting the mixture to uniform stirring using a magnetic stirrer. The viscosities of these emulsions were measured at constant temperature by rotating cylinder method using Brookfield Digital Rheometer. The uniformity of the preparation of the emulsions was confirmed by the reproducibility of the results. Th7 measured viscosities were generally found to be independent of the torque under the experimental conditions so that the two-phase mixture could be considered as a Newtonian liquid. The variation of viscosities with temperature and the effect of addition of a surface-active substance were also studied in this work.The measured viscosities were found to be· higher than those of both pure water and silicone oil. The experimental viscosities were found to increase with increasing concentration of water. The influence of surface tension on the viscosities was examined by adding surfaceactive agent to the mixtures. The result is discussed and compared with theoretical models developed by Einstein, Taylor and Oldroyd."

Jan 1, 2000

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000

By G. Coryell, E. Brack

"Remaining competitive in today's metal markets requires that copper smelters utilize the latest technology offered in process control, data acquisition, and process optimization. State-of-the-art tools like minicomputers, personal computers, and microprocessor based controllers provide real time process information that assist in making proper adjustments to the overall control strategy of an operating plant. The database accumulated by such systems broaden process knowledge, thereby reducing costly errors and plant downtime.IntroductionThe ASARCO Hayden Plant is located approximately 80 miles southeast of Phoenix, Arizona. The plant was commissioned in 1912 for the purpose of smelting copper concentrates from the surrounding mining district. Copper was produced for many years using calcining, reverberatory smelting and copper converting techniques. With the stricter environmental controls of the 1970's, the smelter experienced substantial declines in efficiency and productivity. It became necessary to identify and install a new smelting technology to maintain the viability of the Hayden plant.In 1980, after evaluating several smelting techniques, ASARCO management selected flash smelting as developed by International Nickel Company (INCO). One hundred and thirty-two million dollars was allocated for the project and construction began in 1982. Construction was completed and the new plant came on line in November of 1983."

Jan 1, 1989

By Susumu Okabe

Injection metallurgy is widely adopted in various fields of metallurgical operations to achieve high productivity. The Mitsubishi Continuous Copper Smelting and Converting Process employs the top blown lance technique for the continuous supply of solid charges and reaction gases into the molten bath, where the agitated bath contributes to enhance the heat and mass transfer and the increased gas/liquid interface area accelerates the reaction. However, excessive splashing of the molten materials accompanied by the injection may cause an unexpected wear of the furnace lining. In order to estimate the splashing rate quantitatively, and to optimize the furnace design and the blowing condition, a physical model study of the top blown gas injection onto the liquid bath was carried out. An equation of the splashing rate was obtained as the function of cavity size, gas velocity and bath properties.

Jan 1, 1995

Sanes are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. The purpose of this investigation was to study and develop a process to separate chromite sand and silica sand from reclaimed sands for a steel foundry. Physical separations were utilized to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches were examined. Experimental results are presented. A method was developed to separate chromite sand from silica sand after mechanical or thermal reclamation. The reclaimed sands are passed through a rare earth magnetic separator to separate chromite sand and magnetic impurities from non-magnetic silica sand. Chromite sand can be recovered from magnetic silica sand or magnetic impurities very effectively using a wet concentrating table. The applicabilities of the separation methods are discussed.

Jan 1, 1995

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuO0.5- CaO-MgO-FeOwAIOl.s?SiO2) slags were calculated. The log (Po2/PS2) versus matte grades of various industrial processes was determined. The PoiPS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Jingwei Lou, Bing Li, Suzhen Li, Miao Shen, Jianguo Yu

"As a main impurity in primary lithium metal, magnesium is difficult to remove because of the very close relative volatility of the two metals. Electrochemical refining provides a possibility to completely remove Mg in the LiCl-KCl melt prior to Li reduction. MgCl2 reduction processes in LiCl-KCl- MgCl2 melt were investigated by cyclic voltammetry (CV), square wave voltammetry (SWV), chronoamperometry and chronopotentiometry. Then potentiostatic electrolysis was carried out and Mg (II) ion was reduced onto a liquid lead cathode from the LiCl-KCl-MgCl2 melt at the Mg deposition potential. The results show that Mg ( II ) is reduced in one step with two-electron transfer. The reduction potential of Mg ( II ) was well defined. The reduction of Mg( II) results in Li ( I ) underpotential deposition at 0.2V more negative potential than that of Mg( II) reduction. Therefore, in order to prevent Li ( I ) from codeposition with Mg, accurately controlling Mg ( II) reduction potential during the potentiostatic electrolysis was necessary. Ninety three to 99 % removal rate of MgCl2 was achieved after 8-12 h electrolysis when liquid lead was used as cathode.IntroductionMetallic Li has been widely used in batteries, light weight alloys and in fusion reactors because of its excellent properties. Currently, the only way in industry to produce metallic Li is by electrowinning from molten LiCl-KCl at about 450 °C [l-5]. LiCl-KCl is the only electrolyte used, because they presents a lower eutectic temperature and KCl shows a slightly higher theoretical decomposition voltage than LiCl, as shown in Table l .The produced metallic Li generally contains 1-2 wt% impurities including Na, K, Al, Ca, Mg, Si, etc. [6l, which are derived from the corresponding metal chloride compounds or metal oxide compounds existing in the LiCl and/or KCl raw materials. These impurities have to be removed by subsequent vacuum distillation at high temperatures to meet the requirements for metal Li purity in the final products. Separation of Mg from Li by vacuum distillation is difficult because their relative volatilities are very close, as shown in Table 2."

Jan 1, 2011

By Yuchun Wang

In principle, supported liquid membranes could be an exceedingly elegant separation process. However they tend to fail by displacement and emulsification of the organic solution in the pores, which allows mixing of the feed and strip solutions. We have stabilized supported liquid membranes comprising moctylamine in nylon and PVDF supports by covering the pores with semi-permeable polyamide films, using an in-situ polymerization technique. Scanning electron microscopy demonstrates that the polyamide films are sensitive to production conditions and the nature of the support. The transport properties of stabilized supported liquid membranes for Cr(VI) are compared with those of unstabilized membranes.

Jan 1, 1998

By Stein Tore Johansen

The flow of a liquid through a large grain filter has been considered. An improved form of the fluid dynamic equations describing flows through porous media is proposed. The theory is applicable to all Reynolds numbers. Particulate inclusions are described by passive scalar fields where only very simple mechanisms for particle removal are included. However, the deposition of particles are allowed to change the "porosity" of the filter. Hence, the flow pattern through the filter will change as the filter ages. The theory is employed to the filtration of aluminum in an industrial grain filter. The model shows that the filter is not effectively designed and there is room for considerable improvement. The dynamic "aging" process of the filter is shown to change the filtration from bed filtration to cake filtration. Finally, the predicted inclusion collection efficiencies are compared to efficiencies measured in an industrial filter. The predicted initial efficiencies are in very good agreement with experimental results.

Jan 1, 1990

By R. L. Player

"The Copper Isasmelt process has been developed over the past 15 years by Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organisation (CSIRO). The first two commercial plants were commissioned in mid 1992.The results of four heat balances on the Mount Isa plant are presented. At a smelting rate of 98 t/hr of chalcopyrite concentrate plus 14 t/hr reverts, the total heat generated was -91MW. Approximately 39% of this energy came from coal, while 50% of the energy reported to the process waste gas. To a first approximation the furnace is near chemical equilibrium.The impurity distribution in the Mount Isa plant was presented. Approximately 91 % As, 85% Cd, 75% Bi, 68% Zn, 60% Sb and Tl, 45% Pb and 30% Te in concentrate was eliminated from the matte.The ""bubble"" frequency of the gas cavity below the foot of the lance was measured at -2. 1Hz. Side bands displaced by -l.lHz modulated the bubble frequency. This was consistent with radial gravity wave motion in the slag bath. The two processes, gas bubbling and wave motion appeared to be coupled together; the bubble frequency was twice the slop wave frequency. IntroductionCopper Isasmelt has been developed over the past 15 years by Mount Isa Mines Limited and the Commonwealth Scientific and Industrial Research Organisation. The process is based on the Sirosmelt lance, invented by researchers at the then Division of Mineral"" and ProcessEngineering ofCSIRO in 1973.The first two commercial scale copper furnaces were commissioned at Mount Isa and the Cyprus Miami Mining Corporation smelter at Miami, Arizona in August and June 1992 respectively.The process concept, the history of the development, and the Mount Isa plant have been described (1, 2, 3).This paper sununarises heat balances obtained on the furnace, the impurity distribution among the output streams and lance injection characteristics."

Jan 1, 1996

By Kazuyuki Kikuta

MMAJ, a govemmental organization in Japan, has carried out a 4 year project for the development of the decontamination and metals recovering technology for the fly ashes from municipal waste incineration. Heavy metals (zinc, lead and copper) are recovered as raw materials for the non-ferrous metals production, without formation of any waste materials to be disposed. More than 500 thousands tonnes a year of fly ashes generation from the municipal waste incineration has been one of the main social issues in Japan, because most of them need to be disposed to the registered areas after decontamination, and occupy 5% of the municipal wastes disposed. The segregation, flotation and chemical process are applied to the treatment of the primary fly ash from municipal waste incineration, and MF (Mitsui-type blast furnace) Process after the chlorine removal to the secondary fly ash. The main results of experiments are -About 90% of heavy metals, zinc, lead and copper, can be recovered from the primary and the secondary fly ashes to the products for the non-ferrous metals production. -Both of the leaching residue from the primary fly ash treatment and the slag from the secondary fly ash treatment can be used as a raw material for the cement production, meaning that the decontamination technology for the ashes without the landfill has been established. -Dioxins in the primary ash can be decomposed satisfactorily, and the dioxins content in the segregation furnace gas is less than O.lng-TEQ/Nm3 without any gas cleaning system

Jan 1, 2003

By Karl A. Gschneidner

Magnetic refrigeration was first used in the mid-1920&apos;s and new developments seem to have taken place about every 20 years, and this is especially true for the mid-1990&apos;s. The active magnetic regenerator magnetic refrigerator has the promise to become the first practical machine utilizing the magnetocaloric effect for cooling (and also heating). The basic principles are briefly discussed. Since the temperature lift for the magnetocaloric effect spans about 50 K, one will need to utilize several ferromagnets with different magnetic ordering temperatures in order to reach temperatures below ~250 K. The basic properties, behaviors, limitations, and new phenomena and knowledge are discussed.

Jan 1, 1997

By M. Y. Mohassab-Ahmed

In an effort to develop a novel flash ironmaking process, the chemistry of selected slags was investigated. In different ironmaking processes, the molten bath (iron-slag bath) is expected to be in contact with gas atmospheres of H2/H2O, CO/CO2/H2/H2O, and CO/CO2. The latter was investigated to allow comparison with the blast-furnace conditions. The slag composition was selected to resemble that of the blast furnace with CaO/SiO2 in the range 0.8 to 1.4. The temperature range was 1550 to 1650°C. The oxygen partial pressure was maintained in the range 10-10 to10-9 atm. The effect of water vapor on the chemistry of the slag as well as the equilibrium reactions involving the slag has been studied for the first time. H2O dramatically affects the chemistry of the slag and strongly affect the phase equilibria in the slag as well as the equilibrium distribution of elements between slag and molten metal.

Jan 1, 2014

By Dilek Kirgöz, Onuralp Yücel, Murat Alkan

"In this study, Mo containing Fe-based alloys, such as Fe-Ni-Cr-Mo, were synthesized using a mixture of Fe203-NiO-Cr203-Mo03 powders reducing with Al powders by metallothermic process which is a high energy efficient, fast and low-cost production technique for synthesis of cast alloys and advanced ceramics. Detailed thermochemical studies were simulated by using FactSage 6.2 Thermochemical software in order to calculate adiabatic temperature of the reactions and effects of initial molar composition on the final products. In the metallothermic processes, effects of stoichiometric Al addition and addition of the oxide powders (Alz03, Si02, CaO, MgO) on the metal recovery and compositions of final alloys were carried out. Final products were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Fe based alloys (Fe-Ni-Cr-Mo) which are used as surface coatings, wear-corrosion-oxidation resistive applications via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By Lamar S. Todd

The direct production of metal from a sphalerite concentrate is an attractive route for primary zinc. A series of operations and conditions have been selected to efficiently cause the following overall exothermic reaction. The process uses a continuous circulation of molten copper for material and energy transfer between the unit operations. Sulfide concentrate is reduced with an excess of superheated copper to make a copper alloy and white metal. The alloy is stripped of volatile metals under vacuum and some metals can be separately condensed. The residual copper and the white metal are fed into a copper converter to be blown with oxygen for desulfurizing and the superheated copper is recycled. The paper will include a detailed material flow sheet for the process, discussion of the operating conditions of the individual units, behavior of minor elements, and zinc quality.

Jan 1, 1999