Search Documents

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By R. C. Warner, L. Mills, S. D. Botts, M. Marticorena

The Antamina Mine is located in the mountainous region of the Ancash Department of Peru at an elevation of approximately 4200m.The 120 km main access road crosses the headwaters of numerous high-value trout streams and is adjacent to pristine lakes, some of very high ecological and scenic value. In addition, the mine discharges mine water and tailings supernatant to the Antamina and Ayash watersheds. These streams provide the primary water supply for irrigation by local residents and provide excellent fishery habitat. The rock walls and earthen diversions constructed by historic and current indigenous residents of Peru are world-renowned and local residents continue this tradition, passed down from the Inca Civilization, for both agricultural purposes and water distribution. The key elements of sustainable development – economic, environmental and social development have been incorporated into Antamina’s sustainable development program through integration of indigenous knowledge and capabilities into enhanced storm water, erosion reduction and sediment control systems. Examples of incorporating indigenous technologies and knowledge into cost-effective and environmentally sound environmental controls are:(1) placement of rock walls on steep terrain to reduce slope length and erosion, (2) installation of rock walls (porous rock check dams) within elongated sediment ponds to increase detention time, (3) construction of rock-lined ditches to convey clean water (4)use of rock walls, with or without geotextile, to function as a seep berm, and (5) appropriate selection and usage of native Andean species for protection of canals and sediment ponds, and steep slopes.

Jan 1, 2004

By M. Abdelkhalek, M. Hepworth, D. Tao, B. K. Parekh

Pre-combustion coal cleaning and post-combustion flue gas desulfurization (FGD) using lime or limestone are the primary methods employed to reduce sulfur dioxide (SO2) emission from coal combustion. These processes generate voluminous pyrite and gypsum solid wastes that are usually landfilled, occupying thousands of acres of land and creating serious land and water pollution problems due to the release of acids and toxic substances. An integrated process has been developed for the combined utilization of gypsum and pyrite wastes by converting them into useful products including lime, sulfur, and direct reduced iron (DRI). The process includes four major steps. The first step is to concentrate pyrite from coal preparation tailings using flotation or gravity separation. The second is the thermal decomposition of pyrite into pyrrhotite and sulfur. This is followed by the reduction of pyrrhotite with carbon in the presence of lime to produce iron and calcium sulfide. The fourth step involves the reaction of calcium sulfide with gypsum to produce lime. The chemical reactions involved in the process were studied using thermogravimetric analysis (TGA) and X-ray diffraction (XRD)techniques. Process variables studied included reaction temperature, time, reactant composition, and purity of reactants.

Jan 1, 2000

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

The Canadian mining industry is one of the strongest in the world. Not only does the country produce a sizable amount of minerals and metals, Canada plays host to hundreds of global mining companies, large and small. The country, for the most part, recognizes the importance of natural resource development, particularly mining, to its economic well being. Like any country, though, there are federal and provincial regulations on the books that the industry takes issue with. But there are also certain economic incentive programs in place to encourage exploration and mine investment. And, unlike the industry and the United States government, the Canadian government and mining industry appear to have a reasonable working relationship.

Jan 4, 2010

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By Hisashi Takahasi, Hironobu Yamazaki

INTRODUCTION The slurry shield method was developed in Japan in 1963 and its experimental tunnelling work was performed in 1965. Although the history of this method is short compared with the conventional shield method in Japan, many companies such as Tekken Construction, Okumura Gumi, Nishimatsu Kensetsu, etc. are engaged at present in developing their own unique system of the slurry shield method. The ground of Japan is generally pervaded with ground water and a large number of districts are covered with soft ground, which is composed of fine sand, silt and clay, etc. Therefore, the conventional shield method has always used compressed air with various kinds of auxiliary methods. However, with this method there have been experienced numerous troubles such as ground settlements, lowering of ground water, oxygen shortage within the tunnel, and so forth. The slurry shield method has been developed with the above background. In recent years remarkable progress has been made from the engineering viewpoint in applying this method to driving various kinds of tunnels such as road tunnels, subways, water supply and sewer tunnels, and other tunnels. Apart from Japan, the slurry shield process using bentonite is carried out in England and Germany. OUTLINE OF SLURRY SHIELD METHOD (1) System of Slurry Shield Method Since the conventional shield method drives tunnels using com-

Jan 1, 1976

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By Lisa Morrison

The 11th Annual Mineral Economics and Management Society (MEMS) conference was held April10-12, 2002, in Montreal, Quebec. It consisted of a series of technical sessions. Each paper addressed the economic issues that are related to the changes that many people believe are now required in the mining industry. Some of the papers were directed at how the mining industry will handle the changes that will be required in its philosophy and operations management. Of equal importance was whether the industry possesses the toolkit necessary to effect these changes and emerge stronger from its challenges.

Jan 1, 2002

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By H. Lyn Bourne

This is the ninth annual tabulation of royalty information. Again this year, some of the older information has been deleted to make room for more than 30 new entries. Several articles and publications crossed the author's desk this past year that relate to mineral valuation and mineral royalty. Tom Loucks presented a paper, "The Valuation of Hard Rock Mineral Property," at the Rocky Mountain Mineral Law Foundation in Santa Fe, NM in July, 1990. His paper gives an indepth explanation of the definitions and concepts related to mineral valuation. It includes descriptions of numerous legal cases that have dealt with mineral valuation and proper reference is given for each case. Loucks works for the Denver Mining Finance Co. Gold royalties generally range from 5% to 7%, net smelter return. However, Severn Brown sent information that shows a much wider variation. Echo Bay Mines reported in its 1989 annual report royalties that range from 1.5 % to 30% for gold from various gold properties. Brown also sent a copy of an article that appeared in the Dec. 27, 1982, issue of Fortune magazine. This issue carried an article by Walter Guzzardi, Jr. "The Huge Find in Roy Ash's Backyard." The article gives the history of Newmont's leasing in Nevada on property that became the Carlin, Bootstrap and Blue Star Mines. The article states that the initial royalty was 10% that escalated to more than 16%. Another property, the site of Gold Quarry, provides an 18% royalty to the same own¬ers. The article makes interesting reading for those interested in mining history.

Jan 1, 1991

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

Introduction The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track" or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.3 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV, Pre-Feasibility Planning Proper early planning and identification of priority items were necessary to expedite project progress. On April 1, 1978, HIMCO leased the rights to the Borealis prospect and initiated exploration activities almost immediately. Since Borealis was showing excellent potential for mine development, an effort to clear the way environmentally was initiated during the summer of 1979. With the Borealis properties located within the Toiyabe National Forest, the US Forest Service (USFS) was recognized as the "lead" or respon¬sible agency for addressing the environmental issues. Early scoping of the environmental issues by both HIMCO and the USFS allowed HIMCO to take the initiative and address two potentially critical issues-archaeological and biological. Third party consultants, agreed upon by HIMCO and the USFS, were contracted to conduct archaeological and biological surveys. Desert Research Institute of Reno, NV, provided archaeological services, and JFL & Associates of Boulder, CO, provided biological services. These efforts began in the fall of 1979 and continued through the summer of 1980. Conservative Design Criteria By adoption of conservation design criteria, flowsheets and processing data required for detail engineering were firmly established with a minimum of impact on schedule. On Oct. 21, 1980, HIMCO formally initiated a feasibility study to evaluate the Borealis project. Four organizations were contracted for particular scopes of work: • John T. Boyd Co.: Ore reserve estimation, preliminary mine plan, and mine capital and operating cost estimation. • Bechtel Civil and Minerals: Conceptual engineering, processing capital and operating cost estimation. • Hazen Research Inc.: Metallurgical testing. • Sierra Pacific Power: Cost estimation for power supply. Metallurgical testing and conceptual engineering of both heap and agitation leach flowsheets were investigated concurrently. Numerous economic evaluations were conducted for both heap and agitation leaching at varying production capacities. The results indicated a heap leaching flowsheet treating 454 kt/y (500,000 stpy) yielded the best economics and was compatible with the "fast-track" development goal. Conservative design criteria was established to provide operating flexibility and ensure plant productivities. A summary of major design criteria is presented in Table 1. HIMCO assembled the results of the studies of the various consultants along with internally generated studies to produce the feasibility document. The decision to supply 100% equity by HIMCO rather than arrange project financing help to expedite the project. Cooperation Between HIMCO and Regulatory Agencies With cooperation and mutual trust established between HIMCO and regulatory agencies, the time required for environmental permitting was streamlined as much as practical. To expedite the required construction permits, HIMCO proposed to the USFS that HIMCO fund the total cost of an Environmental Assessment Report (EAR) and that issues be addressed at the technical level of an Environmental Impact Statement (EIS). The previous studies on the critical issues of archaeology and biology provided HIMCO with the information to satisfy the proposed approach. Houston International Minerals and the USFS agreed to have Environmental Research and Technology (ERT) of Fort Collins, CO, prepare a draft EAR for the USFS.

Jan 11, 1983

By K. Burke, G. Zhan, A. Mayer

A cover with capillary barrier effects (CCBE) is being constructed on the AA Leach Pad at the Barrick Goldstrike Mine site near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study has been conducted on a small-scale test cover placed on the AA Leach Pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2001

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005