Search Documents

By E. L. Mann, Robert L. Virta

Asbestos is a generic name given to six fibrous minerals that have been used widely in commercial products. The six types of asbestos are chrysotile, crocidolite, amosite, anthophyllite asbestos, tremolite asbestos, and actinolite asbestos (Table 1). Chrysotile is the asbestiform variety of serpentine. Crocidolite, amosite, antho-phyllite asbestos, tremolite asbestos, and actinolite asbestos are the asbestiform analogues of riebeckite, cummingtonite-grunerite, anthophyllite, tremolite, and actinolite, respectively. Although amosite is an acronym for the Asbestos Mines of South Africa (AMOSITE) and does not specify a mineral type, it generally is composed of cummingtonite-grunerite asbestos so the terms are assumed to be synonymous.

Jan 1, 1994

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

Little faith can be placed in a coal resource estimate without a clear understanding of the estimate's accuracy. Different types of coal resource estimates require different levels of accuracy. Prospecting surveys typically are done with widely spaced boreholes, while a much higher level of accuracy is required for mine design. Either way, a measure of the accuracy clearly indicates the level of confidence that can be placed in the results of the estimate. Geographic information systems (GIs) are becoming a commonly used tool for resource estimation because they not only provide a database management platform but also the graphical capabilities to visualize resource characteristics. interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at multiple locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 2000

By Dell H. Adams

Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining.

Jan 1, 1981

By J. R. Gaw

Recent events pertaining to U. S. energy needs and development of alternative energy fuel resources have made the American public more aware of past and present coal mining operations, and their impacts on the nation's economy and environment. This awareness has developed rapidly due to increased government involvement and consequent media coverage. This is true particularly in the Western states and in Texas. One of the consequences of this increased public awareness is public concern over the perceived and real consequences of mining operations. Emphasis has been placed on potential releases of toxic and hazardous substances, and possible carcinogens. The result of this public concern is a mounting effort at both state and Federal levels to promote stricter laws regulating the mining industry.

Jan 1, 1992

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By J. B. Webster

Health and Safety in the work place is of primary concern to the underground coal industry. Control of dust in the underground environment is of major importance in this concern. Utah Power and Light Mining Division has undertaken extensive studies to determine and control the various sources of respirable dust in underground high production sections. Determination of dust sources has been achieved by real-time aerosol sampling and standard gravimetric sampling on individuals and in various suspect locations. Some sources are diesel roadway dust, outby crushing, and handling equipment, face sloughing, water spray roll-back, and mining equipment. Once identified, the dust sources are suppressed or controlled and/or the workers are directed from areas of greatest potential exposure.

Jan 1, 1990

By V. L. Brant

The estimated total energy demand for the U. S. is 60 quadrillion BTU for 1970 and is expected to more than double by the year 2000. Today the energy crunch is here. It is evidenced by brownouts to conserve electrical energy, and the shortage of gas and oil. Many such headlines, including suggestions for energy rationing, are in the news today. Paradoxically we have an abun¬dant source of energy in the form of coal. Energy consumers, however, are geared to use fuel in other forms. It is the intent of this presentation to discuss processes under development for conversion of the energy contained in these vast coal reserves to more usable forms. Coal conversion to synthetic fuels should be of particular interest to those engaged in mining. Coal consumption in a single conversion plant is expected to range from 10,000 to 40,000 tons per day. Plants will be located at the mine mouth and will operate continuously 24 hours per day, seven days per week. Further, many such plants will be needed., For example, looking at natural gas only, the supply/demand gap is estimated to reach 13 trillion cubic feet per year by 1985. Assuming that gas from coal conversion were to fill only 101, of this gap, 15 plants producing 250 MMSCFD would be required. These plants would consume about 90 million T/Y of coal or 135 million T/Y of lignite. It will indeed be a challenge to mine, suitably prepare, and transport coal at these projected volumes without interruption. Many ideas have been conceived for better utilization of coal and these are in various stages of development. Those supported by public money are covered by the Annual Report of the Office of Coal Research (OCR), Department of Interior. The two processes to be discussed, the Consolidation Coal Company's (Consol) C02 Acceptor Process (1)(2)(3) and The Pittsburg and Midway Coal Mining Company's (PAMCO) Solvent Refined Coal Process (4)(5) are both sponsored by OCR.

Jan 1, 1970

By John W. Wilson

INTRODUCTION In the past, the cost and time required for the construction of shafts has played an important part in the planning of underground mines. For reasons that are discussed later, the economics and technology of shaft construction in the future can be expected to play an even greater role in the planning of new mines and the operation of existing mines. Indeed, the very feasibility of a proposed mining venture may depend on the cost and timing of the shaft requirements. The most commonly used shaft sinking methods used today for excavating vertical shafts are discussed and the need for new technology and methods emphasized. In one study by the U. S. Bureau of Mines, it was reported that the coal industry in the United States alone could require 170 to 190 new shafts per year on the basis of doubling current production by the mid 1980's or 70 to 90 shafts on a more moderate coal production expansion program. This study concluded that the attainment of the required number of shafts would be unlikely with the present shaft sinking resources and costs. In order to meet the requirements for shafts in the United States coal and metal mining industries, more efficient and speedier shaft construction methods will be necessary. Current shaft sinking methods are, in the main, labor intensive, and it is noteworthy that it is becoming increasingly difficult to attract the work force required to sink shafts conventionally. Because of this situation, some attempts at mechanization have been made to compensate for this ever-increasing scarcity of trained

Jan 1, 1976

By David A. Summers

In May 1975 the U. S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a long-wall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting head.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the pillar over onto the conveyor (Figure 1). There were several potential advantages foreseen for the system of which perhaps the most significant were the elimination of coal dust from the working area2 and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in equipment horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of mines contract. The experiments showed that it was more advantageous to work at a pressure of 10,000 psi with an estimated flow rate of 50 gpm than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1977

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

By Angus Campbell, Michael J. Gobla

Numerous techniques for treating, controlling, and preventing acid rock drainage have been applied at the Summitville Mine Superfund Site. Challenging aspects of the remote mine site include the wide-spread occurrence of acid-generating soils and rocks, extensive surface and underground mine workings, and a cold and wet climate. Water treatment was an immediate necessity when the Government took control of the abandoned site in December of 1992. Subsequent reclamation activities have emphasized prevention and control of ARD to minimize future water treatment requirements. A combination of conventional, innovative, and experimental methods are being applied to successfully mitigate ARD at Summitville.

Jan 1, 2000

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By J. M. Keating, R. L. Wiegel

Those processing plants which depend on flotation for their mineral separations are always looking for reagents which are cheaper, more selective or in some other way may provide improved economic performance. This paper describes the rationale for and some results from applying a statistically based approach to reagent testing in those flotation plants which still rely on experienced operators for manual flotation control.

Jan 1, 1986

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860's by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

By Joe Hachey, Jerry Dorn, Jeff Schutt, Derek Penrice

"Sound Transit’s East Link Project, a $3.7 billion (2015 $), 14-mile light rail extension, will connect downtown Seattle with the rapidly developing east side cities of Bellevue and Redmond. Among the most technically challenging aspects of the Project is the 2,435 foot long Downtown Bellevue Tunnel (DBT), which will be constructed through the central core of Bellevue underneath 110th Avenue NE using a combination of Sequential Excavation Methods (SEM) and cut and cover tunneling. The 1,980 foot long central SEM component of the DBT will be mined at shallow depth through challenging and complex geology, comprised of glacially overconsolidated soils, containing both regional and perched groundwater conditions and in close proximity to existing high rise buildings. The paper shares lessons learned from the planning decisions and risk based approach to the investigation, design and procurement processes which shaped the DBT configuration and enabled a successful transition to the project’s construction stage. INTRODUCTION The East Link Project is a voter-approved $3.7 billion (2015 $), 14-mile extension of the existing Sound Transit (ST) light rail transit (LRT) system from downtown Seattle, across Lake Washington via I-90, to the cities of Bellevue and Redmond on the east side of Lake Washington. With targeted completion in 2023, East Link will provide riders with an efficient and reliable connection between the largest population and employment centers on the east side and downtown Seattle. The project alignment is indicated in Figure 1 below.ST completed the Preliminary Engineering (PE) phase of the East Link project in late 2011. Subsequently the final design contract for the easternmost seven miles of the project was awarded to the H-J-H Team, a joint venture comprised of HNTB, Jacobs Engineering and Hatch Mott MacDonald in February 2012. H-J-H’s final design scope includes approximately 7 miles of double-track LRT between the east end of the I-90 East Channel Bridge and the Overlake Transit Center Station. While the project scope is extensive and diverse, the focus of this paper is the DBT. The DBT is located immediately north of the East Main Station, and travels approximately one half mile through downtown Bellevue under 110th Avenue NE between Main Street and NE 6th Street; terminating at the Downtown Bellevue Transit Center (BTC) Station. The location and extent of the DBT is indicated in Figure 2."

Jan 1, 2016

By O. J. R. Baena

Mining activity in the Segovia region in NE Colombia is the main source of employment in the local economy. This has created major problems of illegality and informality mining associated with a high social and environmental impact, as inefficient technologies are used and high consumption of toxic substances required in the process of gold recovery by amalgamation and cyanidation. In this work is presented mineralogical characterization of six local mills and studied beneficiation processes developed in them. With the results presented a proposed plant design that eliminates the use of mercury by replacing gravity concentration processes taking advantage of the characteristics of the treated material. Significant results were obtained regarding the recovery of precious metals and present a methodology that can be replicated in other mineral beneficiation plants that use gold amalgamation processes. This implies a significant reduction in mercury use and decreased risk of human contamination associated with this.

Feb 23, 2014