Search Documents

By E. Martinez

A heavy mineral sand sample was tested containing 13% heavy mineral consisting of rutile, zircon, and ilmenite. Eleven tests were run at a mill site with a Mineral Deposit Limited MG 4 spiral to determine the effect of the addition 0; magnets to the spiral compared to conventional gravity separation. Different magnet configurations and field strengths were tested. Optimum results were obtained with the spiral retrofitted with magnets. The heavy mineral content of the concentrate was increased from 55.5% in the control to 64.2% with the magnets. The 8.7% improvement in heavy mineral recovery was due not only to the weakly-magnetic ilmenite, but also to increased recoveries if the non-magnetic zircon and rutile. The increased recoveries were achieved with no loss of concentrate grade.

Jan 1, 1992

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Harry Leslie Bullock

With silica making up more than 27% of the earth's crust, its oxides amounting to more than 59% of the igneous rocks and quartz the most prevalent of the main free oxides, it follows that the mining engineer' is in constant contact with quartz, mainly as a gangue material to be removed as completely and economically as possible and sometimes as a valuable mineral to be purified' for the chemical,, ceramic or glass industries. Water scarcity under desert or semi-arid conditions, dwindling water supplies and difficulties of wet waste disposal in many locations and trouble from freezing in arctic locations make dry benefication more and more desirable. Advances made during the last few years in apparatus and methods and a steadily increasing knowledge of solid state physics are widening the field open to the economical application of electrostatic separation.

Jan 1, 1967

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and thereby reduces processing costs, recovery losses, and refuse generation levels. In this paper, new approaches for optimal control of the segregation process, using time series models and empirical distributions, are presented and demonstrated using field data.

Jan 1, 1998

By Alexander I. Feldman, Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

An extensive geotechnical monitoring program was used to assess ground and liner behavior, provide input to a Disputes Review Board, and verify design assumptions during construction of the Mt. Baker Ridge Highway Tunnel along I-90 in Seattle, Washington. The stacked-drift tunnel liner was constructed with twenty-four 2.9 m diameter concrete-filled drifts forming a semi-flexible compression ring, followed by excavation of the 19.4 m diameter soil core. Instrumentation data was used for monitoring hillside stability, liner deflections and loads, impacts on adjacent highway tunnels, for back analyzing soil properties, and for helping to limit construction-induced settlements to about 6 cm.

Jan 1, 1987

By A. Cecala, J. Noll, J. Hummer

The National Institute for Occupational Safety and Health has observed that many control rooms and operator compartments in the U.S. mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room that had no cleaning system for intake air, a filtration and pressurization system originally designed for enclosed cabs was modified and installed. This system was composed of two filtering units: one to filter outside air and one to filter and recirculate the air inside the control room. Eighty-seven percent of submicrometer particles were reduced by the system under static conditions. This means that greater than 87 percent of respirable dust particles should be reduced as the particle-size distribution of respirable dust particles is greater than that of submicrometer particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced, which is an important component of an effective system and minimizes the entry of particles, such as dust, into the room. The intake airflow was around 118 cfm, greater than the airflow suggested by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) for acceptable indoor air quality. After one year, the loading of the filter caused the airflow to decrease to 80 cfm, which still produces acceptable indoor air quality. Due to the loading of the filters, the reduction efficiency for submicrometer particles under static conditions increased to 94 percent from 87 percent.

Jan 1, 2015

By Robert W. Lawson

INTRODUCTION The two basic types of mine-air compressors are the positive-displacement compressors and the dynamic compressors. Positive-displacement compressors con¬fine successive volumes of air within a closed space and increase the pressure by reducing the volume of that space. Reciprocating and rotary compressors operate on this principle. Dynamic compressors utilize an impeller to acceler¬ate the air, with the increased air velocity converted to pressure through a stationary diffuser. Centrifugal compressors and turbocompressors operate on this principle. Reciprocating Compressors Reciprocating compressors include both single-stage and multistage units. For mine service the most com¬mon is the two-stage intercooled compressor having an atmospheric pressure intake and a discharge pressure of 689 to 861 kPa (100 to 125 psi). The cylinders of a reciprocating compressor may be either single acting or double acting. In the single-acting cylinder, compression occurs on only one side of the piston, while, in double¬acting cylinders, compression occurs on both sides of the piston. Fig. 1 shows a cross-sectional view of a typical two-stage double-acting water-cooled reciprocat¬ing compressor. Fig. 2 illustrates the sequence of opera¬tions occurring in the cylinder of a reciprocating com¬pressor. Most modern mine compressors are double acting and are driven by electric motors. Induction motors are used on low-powered compressors, and synchronous motors are used on larger compressors. Steam-driven compressors once were common and still are applied where a reliable source of low-cost steam is available. For this type of compressor, steam is a desirable power source since a governor that senses the discharge pres¬sure can be used to control the steam inlet. This can be used to regulate the compressor speed to compress only air sufficient to meet the mine's requirements (up to the capacity of the unit). Unlike a constant-speed electric¬driven compressor, no other regulation is required for the cylinders of a steam-driven unit. Rotary Compressors Rotary compressors include sliding-vane, liquid¬piston, two-impeller straight-lobe or cycloidal, and helical-lobe units. Each of these has specific advantages and applications. Of these, the helical-lobe or "screw" compressor has the greatest application for supplying "100-lb air" [689 kPa (100 psi) ] to small- and medium¬size underground mines. Fig. 3 illustrates the operation of a sliding-vane compressor. Fig. 4 illustrates the operation of a helical lobe or screw compressor. Fig. 5 illustrates the operation of a two-impeller straight-lobe compressor. Fig. 6 illustrates the operation of a liquid¬piston compressor. Centrifugal Compressors Centrifugal compressors deliver 0.94 m3/s (2000 cfm) or more of air, and they are best suited to supply¬ing large volumes of compressed air for base loads. The efficiency of a centrifugal compressor declines rapidly when its operation deviates from its design point. If the power cost is not a critical consideration, a centrif¬ugal compressor is attractive as a result of the low initial and installation costs and the high degree of reliability. Fig. 7 illustrates a typical four-stage centrif¬ugal compressor, and Fig. 8 is a cross section of this type of unit. COMPRESSOR SELECTION The process of selecting a compressor requires sev¬eral considerations, including the capacity, the control system, the location, the power supply, and the cooling provisions. Compressor Capacity To determine the required capacity, the total air quantity and pressure requirements must be calculated. The air consumption of various tools, as listed in Table 1, must be included in this calculation. Some of the other considerations include: 1) The correction factor for altitude, as listed in Table 2, must be included in the calculation. While pneumatic tools require additional compressed air as the altitude increases, the compressor produces less. 2) A correction factor must be incorporated for the use of multiple tools. Table 3 lists appropriate correc¬tion factors for rock drills.

Jan 1, 1982

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By Y. Xi

This paper offers an algorithm to determine the optimal panel size with the objective of minimizing the overall stripping cost. The approach is presented both in analytical form for regular layers of coal and overburden, and in graphical form for the cases of irregular and multiple coal seams. When the optimal panel width needs to be changed due to some circumstance, we prove in general that increasing the panel width is better than reducing it in both economics and operational efficiency.

Jan 1, 1994

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By G. M. Matheson

Mining in the Colorado Springs coal field took place from the 1880's to 1940's. The depth of mining in the coal field varied from about 10 meters to over 150 meters. Review of sequential historical aerial photographs from 1937 to 1960 indicated about 2400 chimney subsidence sinkholes had developed throughout the study area. Statistical analyses of the location and size of these sinkholes with respect to the time since mining, depth of mining, mined thickness and type of mining indicated definite trends in the time of occurrence, size, and location of these features. This data is valuable in the assessment of potential future subsidence in this and other areas of similar mining conditions.

Jan 1, 1985

By Hossein Kazemi

This article is a review of fluid flow and mass transport in fractured rocks. The topics include: single-phase and multiple- phase flow theory, formation productivity or injectivity improvement by artificial fracturing, and mass transport associated with fracture acidizing. Possible extension and application of such ideas to in situ mining in fractured rocks are presented.

Jan 1, 1974

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Fig. 1). A property of Yamana Gold Inc., it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88 t (3.1 million oz) of gold. Crushing operations for the openpit mine are located in a 13,500-m3 (477,000-cu ft) underground cavern with a ceiling height of 22 m (72 ft). More than 3,600 m (11,800 ft) of tunnels are used to access the cavern and convey the ore. The project as described in this paper relates to the design and construction of the main cavern, conveyor system exit tunnel, the mechanical system access tunnels and two 4.2-m- (13.7-ft-) diameter shafts (Ore Pass #1 and Ore Pass #2) (Fig. 2). Preliminary engineering for the project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc. (Rizzo), was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By Brian V. Roulston

Potash is Canada's leading industrial mineral in terms of value of production, with 11.1 M tonnes of muriate of potash produced in 1992 for a value in excess of $1 billion U.S. Each tonne of potash produced generates about 2 tonnes of waste salt, together with slimes and brine. The disposal of these waste products, particularly the salt and slimes which are discharged on the surface, has recently become an environmental concern. This concern is forcing companies and regulatory authorities to review disposal practices. In New Brunswick, on Canada's east coast, Potash Company of America operates a mine at which 2 M tonnes of potash ore and 0.5 M tonnes of rock salt are mined each year. The mine is situated in an environmentally sensitive area, noted for its dairy farming and salmon angling. In such an area it was recognized that the storage of waste on surface would be unacceptable, and the mine was designed around this principle. Three main waste streams - salt, slimes, and brine - must be managed as an integral part of the mining system. Around 1.5 M tonnes of fine salt tailings from the milling process and the rock salt screening operation, are sent directly to the active cut-and-fill potash stopes to be used as backfill. Slimes and excess brine from the mill are piped underground as a slurry to be discharged into one of the basin shaped stopes created by mining of the rock salt. While the slimes settle out, the clarified brine is withdrawn from part of the stope to be pumped to surface as a feedstock for the evaporator - a process which recovers the contained potash values in the brine. By designing a system which integrates the mining, processing and disposal of all product streams, and by careful production planning, it has been shown that zero effluent potash mining is possible and points the way for the industry in the future.

Jan 1, 1995

By W. J. Miles

Oil based drilling fluids utilize a number of industrial mineral products to accomplish oil and gas drilling in several environments where water based drilling fluids are less effective or inappropriate. These industrial minerals include: organically modified bentonite, organically modified lignite, barite, hematite, mica, calcium chloride and other salts. A variety of organic products are also utilized in oil based drilling fluid formulations. Oil based drilling fluids are preferred in several drilling situations because: they can be used to drill through water sensitive formations; they produce holes that are very close to the drill bit gauge; they exhibit high temperature stability; they are more environmentally acceptable; they minimize producing formation damage; they provide faster drilling rates when used with new polycrystalline diamond drill bits; they minimize pipe sticking and lost rig time.

Jan 1, 1986

By R. H. King

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. So far, we have developed and reported on algorithms that automatically produce accurate time-study reports of continuous miner data from kilowatt sensors at the Deserado Mine, and we are extending the system to accept other types of sensor data input. This paper focuses on AI techniques that improve accuracy of the numerical algorithms in the PRS module. Additional AI work for the KRS module is summarized in this paper.

Jan 1, 1989

By Peter G. Zambas

In planning an underground room and pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore-body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1971