Search Documents

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

By Rustyn Sherer

Curis, the name of a new Arizona-based mineral development company, is an acronym which stands for ?Cu? (elemental symbol for copper), ?r? (recovery), ?is? (in situ, the Latin for ?in place?). The company was created specifically to advance the development of the Florence Copper Project in Florence, AZ and to pursue other next generation copper development projects in progressive jurisdictions around the world. ?We are extremely excited about this project,? said Curis Resources president and chief executive officer Michael McPhie. ?We?re here to set the standard for Greenfield in situ copper recovery (ISCR) operations in Arizona and around the world. We believe in our people, our technology and our process; and we are passionate about our commitment to environmental stewardship and community development. We?re making a long-term investment in Florence, and in Arizona.?

Jan 1, 2011

By D. Maxton

INTRODUCTION This paper traces the application of High Pressure Grinding Rolls (HPGR) at industrial and pilot scale in Australia. The Argyle Diamond Mine installed the first of two smooth segmented HPGRs during 1990 in an open-circuit secondary-tertiary crushing application to increase throughput. In 2002 a third HPGR was added to improve liberation and so increase the recovery of smaller diamonds. The latest improvements in wear technology (tyre with tungsten carbide studs) were incorporated in the design of this machine. Extensive HPGR pilot-plant trials were undertaken during the 1990s at both the Kalgoorlie Consolidate Gold Mine and the Boddington Gold Mine. The purpose of these trials was to evaluate HPGR as a method to increase throughput, as an alternative to SAG milling, and also to ascertain if downstream benefits existed. One of the challenges for HPGR circuit designers is to translate what occurs at small laboratory and pilot scale into what is likely to happen in a full-scale circuit. Scale-up from pilot machine results is normally recommended by manufacturers. However, such tests need relatively large quantities of material, particularly if meaningful data on wear are to be obtained. Laboratory tests are preferable, as they need relatively small quantities of ore, but may be questioned in terms of how they relate to full-scale operation. Modelling and simulation have played a particularly important role in this respect in Australia. Models are available which have proven to be very accurate at being able to scale throughput and specific energy response from laboratory to industrial machines. More recently, work in Australia has also been done in developing a model which has the potential to scale laboratory wear data as well.

Jan 1, 2004

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By Raymond K. Will

Computers are becoming increasingly valuable tools in the mining industry as a greater variety of appropriate hardware and software becomes available, combined with greater acceptance by management, Within a given time period an engineering staff can evaluate or design a project to much greater detail and higher accuracy by utilizing computers once suitable programs have been developed. We are all aware that throughout the world the decreasing grade of minerals coupled with increasing waste to ore ratios necessitate larger capacity, longer term mining operations and attendant higher capital costs. Computers can be of assistance in all stages of mineral exploitation, from geologic exploration through mine feasibility studies and design, to marketing and transportation. Because of the high speed with which data can be digested and manipulated by computers, preliminary information from any stage of investigation can be analyzed to assist in further guidance of that stage. By use of preliminary mine feasibility studies, financial forecasts and sensitivity analysis, even information from a far-removed phase such as marine transportation of the product, can help guide the exploration phase to a realistic target.

Jan 1, 1973

By Kostas Fytas, Pierre Bousquet, Bill Evanelou

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidise to produce low pH water. This acid effluent has the potential to mobilise any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pynte is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidises a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2000

By Dipl. -Ing. H. -J. Sager

The ‘Westerschelde Tunnel’ underpasses the estuary of the Schelde in the Netherlands. The tunnel will consist of two tubes which are driven by two hydroshields (slurry shields). The tunnels will each have a length of approx. 6.6km and a bore-diameter of 11.33 m. Demanding ground conditions had to be considered during the design of the shield machines. Loose sands, extensive clay formations and high ground water pressures of up to 6.5 bar will be encountered during the tunnel drive. The tunnelling activities will start in the middle of 1999 and are scheduled to end by the end of 2001.

Jan 1, 1999

By Paul F. Ph. D. Ziemkiewicz, Courtney D. Black

According to the American Coal Ash Association, 105 million tons of coal combustion products (CCP) were produced by the power generating utilities in 1997. Of that total, 1.68 million tons were used in mining applications (ACAA, 1997). Results have ranged from the environmentally beneficial to neutral and, in some cases, detrimental. Twenty years ago coal ashes: bottom and fly ashes constituted nearly all CCPs. With the shift to new emission control technologies at power plants, however, large volumes of new products are being generated. Many do not lend themselves to traditional ash applications such as cement formulation. Many CCP disposal sites are not documented with reliable pre and post application monitoring. In this report we discuss types of CCP, their relevant characteristics and the mining environment. We have attempted to identify a range of documented applications and to draw conclusions about their environmental effects including benefits and adverse impacts.

Jan 1, 2000

By William I. Weisman

The annual consumption of fluorspar in the United States, in the last 10 years has doubled. In 1971, when 1,344,742 tons were consumed, almost 45 percent of this amount was used in the production of steel and nearly 50 percent was consumed in the manufacture of hydrofluoric acid. Of the hydrofluoric acid produced, about one-third was used in the manufacture of aluminum electrolytes for production of primary aluminum metal and the balance was consumed in the manufacture of a variety of fluorocarbons and other chemicals. A small amount of fluorspar, constituting less than five percent of total consumption, was used in the foundry industry, and in the manufacture of glass, enamel, cement and other products. It is apparent that a continuing supply of fluorspar will be required to meet the demands for these vital metals and chemicals in our expanding industrial society. Domestic fluorspar production meets only approximately 20 percent of our needs. Hence, it is essential that the United States maintain a healthy domestic fluorspar industry in order to have adequate domestic reserves available at times of emergency and to protect this country from becoming solely dependent on foreign sources for this strategic commodity.

Jan 1, 1973

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

"Above ground, elevated belt conveyors that span more than 200 m (656 ft) between support points can cross valleys, rivers, forests and buildings with a minimal footprint. The cable bridge conveyor (CBC) is a new type of suspension bridge based belt conveyor system that has long spans between support points. It combines a typical belt conveyor and an improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The CBC’s compatibility with current belt conveyors allows versatility in application.A belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground-based or elevated conveyors (Zhang, 2014). The ground-based conveyor has the lowest structural cost when the conveyor is placed on an existing road. Maintenance access is easy and straightforward. Compared to the groundbased conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has a smaller footprint and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss-type structures, with a typical span of 15 to 25 m (50 to 82 ft) between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of a triangular truss-supported conveyor is around 30 to 40 m (100 to 130 ft), while the weight is about 10 percent less than conventional box truss with a shorter span (Jennings, 2013).Long-span elevated structures based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100 to 400 m (330 to 1,312 ft) and beyond. The wide distance between the support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long-span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2014

By Karin Bäppler

Hydropower produces almost two-thirds of the world’s renewable electricity generation and delivers a major contribution on the ambition of the Paris Agreement and Sustainable Development Goals (SDG) with a range of benefits to society and environment. These include clean and flexible generation and storage in addition to reduced dependence on fossil fuels and avoidance of pollutants. The Limberg III PSP is one of the European projects that addresses the implementation of the UN SDGs. The challenge of the project is the construction of a 770 m long pressure shaft to be excavated with a TBM at an inclination of 42°.

Jun 13, 2023

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By Yu-ren Jiang

Novel compounds of hydroxycarbamoyl carboxylic acids, including 2-hydroxycarbamoyl -3-methlcyclohexane carboxylic acid (HCMC), 2-hydroxycarbamoylmethyl decylen-4-yl carboxylic acid (HCDC) and 2-hydroxycar-bamoylmethyl tridecylen-4-yl carboxylic acid (HCTC) were synthesized. The flotation behaviors of diaspore, kaolinite and illite using these compounds as collectors were investigated. The flotation results revealed that the floatability of the minerals was, in descending order, diaspore and kaolinite, followed by illite, and the ability to collect the minerals was, in ascending order, HCMC and HCDC, followed by HCTC. At a dosage of 2×10-4 mol/L, both HCDC and HCTC show a strong ability to collect diaspore and a weak ability to float kaolinite and illite. The flotation recovery of diaspore is over 90% and that of kaolinite and illite less than 30%. Moreover, Fourier transform infrared spectroscopy (FTIR) spectrum and zeta potential, as well as the adsorption amount, indicated that the adsorption interaction between HCTC and diaspore was primarily a kind of chemisorption in the form of chelate rings, while the interaction between the collector and aluminosilicate mineral was dominated by physisorption. It was concluded that the novel hydroxycarbamoyl carboxylic acid compounds are highly selective collectors for the flotation of diaspore vs. aluminosilicate minerals.

Jan 1, 2011

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993

By W. Zhang

"The adsorption of collector on bornite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is very similar to the one obtained with chalcocite/xanthate system. However, the result also clearly shows that the adsorption of xanthate on bornite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The obtained AFM images also showed that the adsorption increases with increasing the collector’s concentration. When Cytec Aerofloat 238, a dialkyl dithiophosphate collector, is used, it adsorb on bornite mainly in the form of an oily substance, which can be rinsed off mineral surface by flushing with ethanol alcohol. AFM images also show that the adsorption of Cytec Aerofloat 238 increases with increasing the adsorption time. INTRODUCTION The adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) Compared to other copper minerals such as chalcopyrite and chalcocite, much less work has been done to study the adsorption collector on bornite. Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of bornite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on bornite was cuprous alkyl xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Buckley et al. (1984) investigated the surface oxidation of bornite by linear potential sweep voltammetry and X-ray Photoelectron Spectroscopy and proposed the adsorption products on bornite depended on the solution potential. Zachwieja et al. (1987) studied the electrochemical flotation of the bornite-ethylxanthate system and reported that KEX reacted with bornite through an electrochemical oxidation reaction forming cuprous xanthate between -0.4 and -0.2v (SCE). Hangone et al. (2005) studied the flotation of a bornite-rich copper sulfide ore using thio collectors and their mixtures and reported that the highest copper recoveries were obtained with the diethyl dithiophosphate (di C2-DTP)."

Jan 1, 2016