Search Documents

By Yong Pan, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate gas dilution situation when the source is located in the extraction drifts.

May 12, 2022

By G. Southam

Bacterial populations play an active role in mineral weathering in subsurface and near-surface environments e.g., supergene enrichment of Cu at Morenci, AZ. An in vitro bacterial biofilm model was used to examine the interaction between Sporosarcina ureae and ionic gold (which is toxic) or amino acid-gold complexes in gold mobility. The immobilization of ionic gold was between 80-90% for 1 week but as the available, cellular reactive sites became saturated immobilization decreased to 14% within 2 weeks. In the asparagine-gold system, gold immobilization occurred at a high rate (80-90%) throughout the experiment with limited toxicity towards Sporosarcina ureae.

Jan 1, 1999

By F. Stanley, A. Noble, G. Luttrell

"The supply chain for coal-fired power stations involve a multi-stage network of mining units, preparation plants, blending facilities and transportation systems. Attempts to optimize the supply chain have historically been difficult due to the lack of communication/coordination between the various groups involved in coal production, transportation and utilization. In light of this issue, a new approach for globally optimizing the coal supply chain called Micro-Price Optimization has been developed to simplify the optimization problem and to provide coal producers with fundamental insight needed to improve the profitability of their operations. This fundamental concept assigns unit values to each particles (or groups of particles) passing through production units. Optimization occurs whenever the maximum tonnage of positive value particles are recovered and passed to market, while the minimum tonnage of negative value particles are recovered. Elements considered by the concept include factors such as target boiler cost/efficiency, waste disposal costs, coal quality parameters, emission penalties, transportation charges, or other quantifiable impact factors. This article reviews the basis for the micro-price concept and provides a detailed industrial case study involving the determination of optimum coal qualities that need to be supplied by mine operators to feed a coal-fired power station. INTRODUCTION The performance of coal preparation plants have long been known to play an important role in determining the overall profitability of mining operations. This significance is due to the fact that the misplacement of just 1 ton/hr of clean coal to reject resulting from poor plant performance can represent nearly $300,000 per year in lost revenues for a mine producing a steam market coal (i.e., 1 ton/hr x $50/ton x 6,000 hr/yr = $300,000/yr). This loss can be even more pronounced, occasionally approaching $1 million per year for each 1 ton/hr of misplaced clean coal, for operations producing high-quality coking coal products sold into the premium metallurgical market (i.e., 1 ton/hr x $150/ton x 6,000 hr/yr = $900,000/yr). Detailed economic studies indicate that improvements in plant yield resulting from increases in organic efficiency have one of the largest overall impacts on mine revenue when compared to other cost centers within the mining operation. One of the first studies to show this important financial impact was reported by Norton-Hambleton Consultants (Norton, 1979). Their study indicated that an unfavorable change in plant efficiency was second only to coal transportation in terms of its impact on profitability, while an unfavorable change in the cost of underground mining was a distance third. This longstanding realization has continued to provide a strong financial incentive for coal producers to optimize the separation efficiency of their coal processing and blending operations."

Jan 1, 2015

By T. Gonzales

Magma Metals Company operates an Outokumpu Flash Furnace, four Peirce-Smith Converters and two Anode Casting Wheels supported by six Anode Vessels. Process gasses from the Flash Furnace and Converters are treated in a two train/double contact sulfuric acid plant. Sulfur capture for the smelter is +98%. The new flash furnace was commissioned on July 7, 1988 and has processed over three million tons of sulfide concentrate without a major rebuild. Magma has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. This paper describes all the procedures, operation control parameters and operating philosophy that has allowed Magma to achieve superior performance.

Jan 1, 1992

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By Ronald L. Wiegel

In the 2000 page Handbook of Mineral Dressing by A. F. Taggart, the subject of material or metallurgical balances is covered in only six pages of eve-straining type. Although Taggart's work was compiled before 1945, and there has been significant progress since then in most areas of mineral processing, the practicing metallurgist's approach to metallurgical balances remains exactly the same as described in those six pages. There are several portions of Taggart's text appropriate to introduce the subject of this paper which I would like to quote: "Milling Calculations. Computations of per¬formance in milling are complicated by the fact that it is a continuous rather than a batch operation, that the quantities of solid materials handled are large and usually mixed with water, hence difficult or impos¬sible to weigh. Fortunately it is possible to determine many facts concerning perfor¬mance without knowing weights, if the value of various constituents is known in some common unit, e.g., the content of some par¬ticular metal or mineral, or of water, or some ingredient soluble therein, or of par¬ticles of a particular size or falling within some particular size range, or the like."

Jan 1, 1979

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

By Victor Despointes, Stephane Polycarpe, Kathryn Kelly, Chris Feeney, Brian Hann, Vojtech Ernst Gall

The Pawtucket Tunnel is a 2.2-mi, 30.2-ft diameter CSO storage tunnel in Rhode Island. The primary tunnel is built using a dual-mode open-EPB TBM capable of sealing the face within 120 seconds to manage poor ground and water ingress which is launched from within a SEM starter tunnel. The main tunnel connects to four adits along its alignment, three of which are SEM tunnels and one being a MTBM tunnel. This contribution describes the selection process, potential risks, and requirements for the TBM, as well as the design of the main tunnel, the adits, and the adit-bored tunnel connections.

Jun 13, 2023

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly-mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala Aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil, Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after 21 months of operation. Water quality in 15 specially-drilled monitoring wells has returned to the original quality level of the aquifer, and chloride concen¬trations in the pumping well have dropped to half the maximum level recorded thus far. Project results are very favorable and provide guidelines for initiation of similar undertakings in localities where needed.

Jan 1, 1970

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By J. A. Mejia

The combination of high-resolution X-ray microtomography (HRXMT) image analysis and Lattice-Boltzmann Method (LBM) simulations has demonstrated the ability to describe real multiphase flow problems in fine coal filtration. The single component multiphase flow He-Chen-Zhang LBM model was used to simulate filtration with actual HRXMT images of pore network structures produced in filtration experiments. The analysis performed on coal, silica, and glass bead filter cakes showed that particle shape and wettability are two of the most important factors in the retention of moisture during filtration.

Feb 23, 2014

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By N. O. Lotter

Studies investigating the evaluation errors in laboratory scale flotation tests for platinum-bearing Merensky Reef in the Bushveld Complex, South Africa, have constructed a quality control model to assure a 95% confidence in the attested data. Specialized knowledge of the mineralogy of the platinum-group elements (PGE), together with acquaintance of evaluation models, validate a systematic checking of the sub-processes of the testwork. These include determination of minimum mill feed sample size, assay head reference distribution, mass balance checks, and specialized sample preparation of flotation test products prior to analysis. A flow schematic of this quality control model is proposed, with an example of test data that produce an error in the metal balance of 0,2% after rejection of outlier data.

Jan 1, 1995

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin (1961) were the first to develop a model for bubble-particle interaction in flotation from first principles by considering the surface forces in wetting (or flotation) films. The model predicted that the energy barriers to bubble-particle attachment arise from the ζ-potentials of fine particles, which corroborates well with an earlier work of Fuerstenau (1957) reported for the flotation of quartz using dodecyl ammonium acetate (DAA) as collector. In the present work, a series of surface force measurements have been conducted by accurately monitoring the changes in bubble curvature during bubble-silica surface interactions. The curvature changes are then used to determine the capillary force, which is the sum of the hydrodynamic and surface forces. By subtracting the former that can also be determined from the curvature changes, one obtains the surface forces (or disjoining pressure). The results obtained as functions of pH and collector concentrations show that control of the ζ-potentials of bubbles relative to those of the silica surfaces is critical for maximizing the negative disjoining pressure, which is conducive to promoting bubble-particle attachment in flotation.