Search Documents

By Bryant Fitch

This paper will review thickening theory, from the ( ) of the practicing engineer, with particular emphasis on ( ) uncertainty or disagreement. It will attempt to outline broadly what we know and what we don't know. This should serve two purpose First, it will warn the process engineer where he might get into trouble. At least it will alert him to the risk involved in uncritically accepting any of the recommended design procedures. Second, it will identify for researchers some areas in which further work might be fruitful. Not too many years ago there would have been little to write on such a subject. We had been designing thickeners for decades, using the classic Coe and Clevenger procedure. As far as we were generally aware, they all turned out to be about the right size. And so if there was anything we didn't know, It certainly wasn't hurting us much. Today we know better. While it is true that in most cases units designed by the Coe and Clevenger procedure (1) will perform satisfactorily, we now know of cases in which they don't. And during the past few years there have been many developments and advances in basic thickening theory. So there is now a lot more room for disagreement, and a whole lot more to be uncertain about. What is "thickening" "Thickening" means different things to different people. For this paper we define it to mean sedimentation behavior characterized by line settling. Solids subside with a clear line of demarcation between settling solids and supernatant. Although the supernatant will usually be clear, in some cases it may be turbid. Line settling must entail that all particles just below the pulp-supernatant interface have the same subsidence rate, so that

Jan 1, 1971

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By C. G. Anderson

Extraction of valuable resources from complex orebodies will become more common. This is obvious for two reasons. First, the cleaner and more readily processed ores have continually been depleted through centuries of mining. Second, new technologies have evolved for effectively handling complex ores. One of these new processes has been in place at Sunshine since 1984. Based on sulfuric acid oxygen pressure leaching with nitric acid as an oxidizer, this patented technology allows silver and copper to be efficiently recovered from a complex sulfide concentrate. As efficient as it is, this process represents novel technology found nowhere else on an industrial scale. As such, a research program was undertaken in 1989 to optimize this leach process and to better understand it. From this study, several potential plant improvements were found and recommended. As a result, two of these options, nitric acid replacement by sodium nitrite and concentrate regrind are now used in day to day operation at Sunshine. Patenting of these changes was recently accomplished (1). Thus, the development, perceived mechanisms, plant integration and potential applicability of this technology will be covered in this paper.

Jan 1, 1994

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

A group of geologists is located in a remote area of North America, without telephone lines, electricity or even running water. They have spent days accumulating data for a mining company that is eager to receive any information about the dig. But the team does not have access to a wired communications infrastructure. So the geologists must wait until they get to the nearest town to transmit their data. TMI Communications has a mobile satellite communication system that allows geologists in the field to transmit their data from remote locations. The company's satellite is the heart of its North American mobile communications network. This satellite turns all of North America, including Canada, Mexico and the Caribbean into a single digital communications cell. Traditional terrestrial communications systems, such as dedicated phone lines or cellular systems, cannot handle a remote geological exploration camp's extensive communications needs. Cellular technology, where available, has high costs and limited applications. For geologists in the isolated areas of North America, accessible and reliable phone service is vital to success. For those who have established temporary camps, TMI Communications' satellite phone service has improved the speed and accuracy of their communications with home base. This wireless network is suited to meet the needs of existing data applications and the challenges of new ones. It can support any one- or two-way, fixed or mobile data transfer. TMI's network enables geologists to transmit exploration results, spreadsheet information and location co- ordinates to anywhere in the world, at any time. This is important if a team needs to relay vital data back to its headquarters to support immediate decision making on a prospect site or a find.

Jan 1, 1999

By İsmail İnce

The purpose of this study is to investigate the index-mechanical properties of igneous rocks by using the electrical resistivity method. Electrical resistivity, index (P-wave velocity, dry density, and porosity), and uniaxial compressive strength values of 48 different igneous rock samples were measured in the laboratory. Simple regression analysis was performed between index-mechanical properties and electrical resistivity values. Strong exponential and logarithmic correlations were found between electrical resistivity and the index-mechanical properties of the igneous rock samples.

Jan 21, 2022

By Y. J. Zhang

This paper presents the results of a recent study on the development of an in-situ testing method for determining the coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using the penetrometer. It is a hydraulically powered device that uses an indenter to press the surface of the borehole until the load reaches the failure point of coal. The pressure and the penetration of the loading pin are recorded by the data acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of pillar strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1995

By Aldin Ardian, Mustafa Kumral, Jagjit Singh

Risk assessment of mining projects is a requirement in the mineral industries. In this process, many risk variables are timedependent, and the only available data are historical time series. Moreover, in the case of a multivariate scenario, conventional forecasting methods fail to capture conditional dependency across the variables, which is important when there is an underlying causal relationship that needs to be modeled for accurate project evaluation. Thus, we investigated the use of copulas to capture the conditional distribution of the factors involved in a mine risk assessment study. We employed a multivariate copula-based time-series approach to model several uncertain variables. The Autoregressive Fractionally Integrated Moving Average - Generalized Autoregressive Conditional Heteroscedasticity (ARFIMA-GARCH) model was used for the conditional mean and copulas were used to model the error distribution, thus capturing the collective variation and dependence pattern across the variables. The method was implemented to model gold prices, copper prices, and the 10-year US Treasury bond yields and to determine the project’s net present value and probability of being economically feasible. The proposed approach can be used for cases where simulation of multivariate time-series is conducted.

Apr 13, 2021

International Technology for the Nonferrous Smelting Industry, by T. K. Corwin et al., Noyes Data Corp., Mill Road at Grand Ave., Park Ridge, NJ 07656, 413 pp., cloth, $36-Describes current and new production processes, and pollution control technology, in the primary nonferrous smelting industry in the US and abroad. The methods described are intended to reduce costs, increase production, and lower pollution levels. Techniques used in copper, lead, and zinc smelting are emphasized and, whenever possible, the authors describe pollution control practices.

Jan 7, 1982

By Joern Katzer

It is vitally important to any tunnel project to have an accurate and reliable survey control network inside the tunnel for layouts, as-built surveys, and to provide guidance to the tunnel boring machine (TBM). However, the concepts and methodology to provide such a survey network are sometimes not well understood. For example, the first anticipated survey task that takes place during the bidding process is often ignored, which is to provide a comprehensive survey network preanalysis for the surface network and tunnel traverse based on survey statistics that will be used to make informed decisions on the survey requirements and methodology. Instead, these steps are often only vaguely based on previous results and prior tunneling experience. But each tunnel is different, and a solution that worked for one tunnel project might be unsuitable for another. The purpose of this paper is to provide tunnel project engineers, managers and surveyors with the general concepts for tunnel survey methodologies and examines several statistical tools for a basic horizontal and vertical tunnel survey preanalysis. These survey statistics tools provide useful estimates of the expected lateral and vertical tunnel traverse accuracies, but are not a replacement for a comprehensive tunnel network preanalysis. The proposed formulas do not take centering errors into account, are using average distances for each traverse leg, and assume that the survey data is free of outliers in the measurements. It is very important that the estimated instrument accuracy is based on true values that are reflective of measurement precisions that are actually achievable inside the tunnel to provide accurate results.

Dec 1, 2022

By J. L. Kearns

The importance of optimizing equipment replacement decisions becomes more critical each year due to the rising costs of buying new equipment versus maintaining old equipment. Replacing equipment when it is physically worn out, or replacing it too soon or too late relative to its Economic Life (when it is economically worn out), is very costly. After extensive literature review and research, Kennecott has developed its Equipment Replacement Guide (ERG) system which identifies, evaluates, and justifies the replacement of uneconomical equipment. The system considers such critical factors as inflation, decreasing work capability, increasing maintenance/repair and operating costs, taxes, time value of money, return on investment, salvage value, and investment tax credit. These factors are used in a system of equations which balance the costs of new equipment against the total operating costs of old equipment. The solution of the equations determines the Economic Life of equipment. Replacement of equipment at the determined Economic Life will earn the specified, required return on investment that is used in the calculation of the Economic Life.

Jan 1, 1979

By S. Chatterjee, A. K. Gorai, Sahendra Ram, Kapil Kumar, J. Anil

Extraction of underground coal or mineral by the caving methods leads to surface deformations and the accurate measurement of this deformation is becoming a demanding task. Thus, the study demonstrates a Persistent Scatterer Interferometric Synthetic Aperture Radar (PS-InSAR) technique for surface subsidence measurement. The method was applied to measure the subsidence level over three mechanized depillaring panels with caving at GDK-11 Incline mine, India. The study was conducted using C-band data of Sentinel 1A/B sensors, which captured the data in the descending path from October 25, 2017 to March 07, 2020. The deformation level was measured based on the identified PS points in the specified region. In this case, 12 zones were identified (4 for each panel), based on the observation of permanent scatterer (PS) points. The maximum subsidence level and deformation rate range in 12 zones are −43.12 to −65 mm and −73.8 to 100 mm/year, respectively. The deformation level obtained through the PS-InSAR technique showed a good agreement with those of the field measurement. Thus, the PS-InSAR technique can detect and monitor the subsidence level over the goaved-out panel(s) of an underground mine using C-band SAR data of the Sentinal-1A/B sensor.

Mar 14, 2023

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By R. E. Doerr

The successful technical demonstration of coarse coal slurry transportation at Consolidation Coal Company's Loveridge Mine in West Virginia suggests that it is now appropriate to seriously consider this technology in other applications, especially the transport of ' coal in surface mining. Early examination indicates that coarse coal slurry transport may be highly competitive with existing haulage systems, depending on a number of factors. These factors are not yet completely defined, but certainly will include production rates, coal physical and chemical properties, terrain, soil conditions, climate, water availability and quality, availability of skilled labor and other economic considerations impacting the existing haulage systems.

Jan 1, 1983

By Biswajit Samanta, Pranjal Pathak

This article presents a customized genetic algorithms (GA) with new crossover and mutation operators to solve the short-term production scheduling problem of multi-mine mineral value chains (MVC). The preceding problem consists of determining the extraction sequence and destination allocation of blocks from all the mines collaboratively while closely meeting the quality and quantity requirements of the processing units subject to relevant technical and operational constraints. The short-term production scheduling is carried out at shorter scales wherein the operations are modeled in a great detail with large number of constraints. This makes the industry-scale instances of the problem computationally intractable for standard mixed-integer programming (MIP) solvers. Thus, a GA-based heuristic approach is developed to obtain nearoptimal solutions to the large-scale instances of the problem in a reasonable amount of computational time. Computational experiments show that the developed GA-based method is a promising way to handle industry-scale instances of the problem. Moreover, the sensitivity analysis on various parameter combinations of crossover and mutation operators indicates that the customized global mutation operator, when used in combination with the customized crossover operators, took on average 12.5% less time than the customized local mutation operator to converge to a solution.

May 21, 2022

By S. S. Wang

Dialkyldithiophosphinates are a new class of flotation collectors for base metal sulfide ores. Structurally, they are quite different from the conventional collectors such as mercaptans, xanthates, thionocarbamates and dithiophosphates. Collectors Structures [Mercaptans R-SHS Xanthates R-OCS-M+ Thionocarbamates R-OCNH-R Dithiophosphates 2 R-CCNH-R' Dithiophosphinates (R) 2-PS-M+ ] In the above structural formula, R and R' stand for a hydrocarbon radical, and M+ is an alkali metal or ammonium cation.

Jan 1, 1982

By J. Stachurski

Flotation tests were carried out on 6 coal samples of different rank as well as their oxidized samples. A mixture of diesel oil and alcohols was used in these tests. Surface oxidation caused a distinct decrease of the flotation recovery with some improvement in the grade The reduction in the recovery increased with increasing the concentration of the oxidizing agent. The floatability of low rank coals was affected by oxidation to a higher degree than medium and high rank coals. The recovery size curves of oxidized samples mere similar in shape to that of non-oxidized coals.

Jan 1, 1990

By Wang Hongwei, Wu Yongping, Cao Peipei, Jiao Jianqiang

Fully mechanized top caving mining of steeply inclined extra-thick seams with variable angles has complex roof rock movement, failure, caving, and filling mechanisms. Moreover, the variable-angle coal seams make rock–equipment stability control challenging. We analyzed rock deformation and failure mechanisms, overburden bearing structures, and working characteristics of supports through physical simulations, field tests, and theoretical analysis of the no. 120210 working face of Zaoquan Coal Mine. Overburden rock movement has distinct regional characteristics, with a large caving height (to the main roof layer) in the upper area, and lower caving height (to the lower main roof) in the lower area. Support loading is regional and unbalanced along the inclined direction. The critical layer of overlying strata migrates, and bearing structures formed by breaking the critical layer exhibit cross-layer generalization along the inclination. The upper region has a cantilever beam structure in the basic roof rock layer; the lower region has an inclined masonry structure with multistage ladders in the breakage basic roof rock layer. Application of a false-inclined working face layout with the tailgate ahead of the headgate and an arc arrangement (radius 28.65 m, arc length 10–20 m) in variable angle areas, and regional control of support working resistance and top-coal caving amounts, control regional failure overburden. Safe and efficient mining was achieved, with the monthly production and recovery rates reaching 344,900 t and 85.86%, respectively. Our results expand the scope of fully mechanized top caving mining and have important theoretical and technological significance.

Nov 23, 2020

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By P. Gelfi, J. Vanderbeek, J. Enriquez

"The Cerro Verde copper-molybdenum mining complex is located near Arequipa, Peru. A 108,000 t/d copper concentrator (C1 concentrator) commenced operation in late 2006 and was debottlenecked to a 120,000 t/d capacity in 2011. A feasibility study, initiated in May 2010, assessed the potential for expanding the processing rate of the large Cerro Verde sulfide reserve via the installation of a second, stand-alone, concentrator (C2 concentrator) capable of processing a nominal 240,000 t/d ore. The feasibility study was successful and the project advanced through engineering, permitting and construction. Ramp up to nameplate capacity was ahead of schedule. The overall project was completed on schedule and within budget. The details of the project and supporting components are described. The design philosophy and design basis of the concentrator facilities are discussed as are factors that influenced the concentrator layout. Risk mitigation features included in the design are reviewed. The factors that drove the successful and rapid ramp up to nameplate capacity are discussed. Operational experiences in the first year of plant operation and project lessons learned are described. INTRODUCTION/BACKGROUND Sociedad Minera Cerro Verde S.A.A. (SMCV) operates a copper mine near Arequipa in southern Peru. Small scale operations operated intermittently until 1970 when the deposit reverted to the ownership of Minero Perú S.A (Peruvian government). Minero Perú S.A. commenced mining and processing of oxide reserves in 1972 and placed an SX-EW plant into production in 1976. The ownership of the property has changed hands several times over the years. Minero Perú sold Cerro Verde to Cyprus Climax Metals in 1994. Cyprus was acquired by Phelps Dodge in 1999. Freeport-McMoRan (FCX) acquired Phelps Dodge in 2007. Several studies were undertaken during the 1990’s that tried to establish the economic justification to process the large primary sulfide resource that underlies the surface oxide deposit. None of these studies produced an economic conclusion until a feasibility study was completed by Phelps Dodge and SMCV in 2004. This study provided the economic justification for the construction of a 108,000 t/d concentrator during 2005 and 2006. The key to the success of this study was identifying a water source that was sufficient to support processing economies of scale. Concentrator operations commenced in late 2006. The original design production rate of 108,000 t/d was achieved on a 30 day moving average basis on the 266th day after ore was first introduced. During 2009, studies and evaluations were performed that had the objective of addressing observed concentrator bottlenecks to allow a production rate of 120,000 t/d to be achieved. The 120,000 t/d figure represents the sustainable production limits associated with the installed primary crusher and tailing thickeners which would have been prohibitively expensive to upgrade. Debottlenecking activities were implemented during 2010 allowing sustained production rates of 120,000 t/d to be achieved."

Jan 1, 2017