Search Documents

By J. K. Horbaczewski

The reclamation of an open dragline pit (Pond A3P-2) at the Gibbons Creek lignite mine in east-central Texas required neutralization of acid mine pit water. At the start of treatment with hydrated lime (Ca(OH)2) on March 28, 2000, the pond had partially filled with 913,000 m3 (740 acre ft) of pH 4.9 water. Another 666,600 m3 (540 acre ft) of pH 3.3 water was pumped in from an adjacent pit (PitA3P- 1). By the end of the project (July 5, 2000), a combined volume of 1,579,000m3(1,280ac-ft or 417milliongal) in PondA3P-2 had been successfully treated to pH 8.2 with 431 t (475 st) of lime. This was two to three times more neutralizer than laboratory trials and detailed chemical titration had predicted. The main reasons for the difference are thought to be the inadequate representation in a laboratory setting of some of the chemical reactions that occurred in the field, including incomplete mixing of reactants, reactions with clay minerals in the pit walls, the kinetics of biologically-mediated reactions and the kinetics of aluminum oxyhydroxide polymerization (aging).

Jan 1, 2002

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By R. Brändle, R. Luis-Fonseca, R. Cornejo, G. Fischer, G. Von Rickenbach, J. Jarufe

Rock damage around underground excavations has been an important hazard in mines and tunnels. Rock dilation generates buckling that needs to be contained before it causes damage to equipment or safety concerns to mine workers. In seismically active mines, rockburst occurrence has been widely recognized as one of the most important hazards in deep mines and tunnels. While there is a wide range of cases where rockburst hazard can be mitigated through dedicated excavation sequences, reentry procedures or exclusion zones, there are still many situations where large unexpected rockbursting may occur, relying only on rock support as the last mitigation measure to prevent production and safety losses. Considering the previous situations, surface support as mesh, plays a major role containing the failed/ejected rock and providing a safe working environment to the underground operations. While there have been considerable achievements in improving mesh resistance, with more than 26Kj/m2 of energy dissipation capacity, there is still a lack of research in the overlapping mechanism and load transfer between contiguous mesh elements. This paper presents the state of the art in static and dynamic analysis of welded and rolled mesh overlaps, based on experimentation carried on by Geobrugg in their Research Center, leaving clearly established that the difference in meshes is not only in levels of energy absorption, but also concluding that in the case of high resistance rolled meshes overlapping is not necessary and the transmission of stresses can be fully guaranteed by using suitable connecting elements. All these characteristics, supported by operational advantages as light weight and mechanized mesh installation, provides a considerable improvement in safety and productivity, improving the economic value of the project

Apr 26, 2022

Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering the seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois, and Kentucky, and by others in Wyoming and New Mexico, have shown the presence of such a gamma background (Nelson, 1989). Natural gamma coal thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company in Pennsylvania and west Virginia (Nelson and Bessinger, 1988).

Jan 1, 1990

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The integrated grouting method, as developed in the USSR, can be applied to multi-purpose operations that in¬clude the construction of shafts, drifts, and tunnels. In the USSR it has been used extensively for primary and final grouting of underground excavations in mining engineering and civil engineering projects. It has been applied in projects where the primary objective was waste contain¬ment. It has also been used to control subsidence beneath buildings located over mined out openings and to eliminate the flow of ground water beneath and around dams. This chapter considers several industrial applications in the form of case histories. The word integrated means that grouting activities were integrated with other activities. 9.1 CASE HISTORIES OF GROUTING FRACTURED ROCK WHEN SINKING VERTICAL SHAFTS The integrated grouting method has been applied most widely in the sinking of vertical shafts in fractured, satu¬rated rock. As explained previously herein, grouting oper¬ations preferably are carried out from the ground surface where they are integrated into the schedule of the setting up of the shaft excavation and construction equipment. Such integration reduces significantly the length of time required for preparation of shaft construction and the time required to sink the shaft. The increased efficiency is achieved by the elimination of cementing operations from the working face upon the penetration of each aquifer. Concomitantly, labor and energy consumption during shaft sinking are minimized because the more complicated and labor-intensive work is carried out at the surface section. Table 9.1 presents the essential parameters for the pri¬mary grouting of saturated fractured rock carried out by the integrated method when sinking vertical shafts. 9.1.1 NAGOL'CHANSK MINE NO. 1-2, VENTILATION SHAFT NO. 1 The integrated method of grouting saturated fractured rock through holes drilled from the surface was employed for the first time during the sinking of vertical shaft No. 1 at the Nagol'chansk mine No. 1-2 in the Don Basin. The shaft had an inside diameter of 6 m. The grouting operations commenced by using cement grout with a density of 1.7 to 1.8 g/cm3. Clay-based grout with cement and other addi¬tives was used only for grouting the aquifers where cement grout proved to be ineffective. By the time of the grouting of ventilation shaft No. 1, hydrodynamic analytical methods were well in hand and a preliminary method for designing isolation curtains had been developed. A method for designing and drilling ori¬ented directional drillholes whose natural curvature re¬flected the characteristics of the fracturing had been devel¬oped. The majority of the necessary equipment had been developed. Clay-based grouts were considered ready for the first industrial application. The hydrogeologic environment at the Nagol'chansk mine No. 1-2 contained many prolific aquifers. According to monitored drillhole data, the total expected inflow into ventilation shaft No. 1 without grouting was 425 m3/hr. This large ground water inflow rate was supported by in¬formation obtained during the sinking of the main shaft and from the auxiliary shaft of the "Nagol'chansk" mine No. 1-2. The construction contractor at the site began sinking ventilation shaft No. 1 to a depth of 217 m by cement grouting from the working face of the shaft. As a result of the cement grouting operations, the inflow of water was reduced from 105.4 to 40 m3/hr over this 217 m interval. However the residual inflow rate caused the shaft to become functional at the depth of 217 m. At this point all grouting operations were transferred to SPETSTAMPONAZHGEOLOGIA (STG) in an effort to improve the operation. In order to carry out preliminary grouting from the sur¬face, seven drillholes were installed and designed for re¬ceiving grout. Drilling was implemented by the ZIF-1200A rig to the design depth of the shaft. The geometry of the principal fracture system that would be encountered by the shaft was estimated while breaking ground using informa¬tion from other shafts. The drillholes were arranged so that they cut through the aquifers uniformly around the shaft. Some preference was given to intercepting the aquifers that were located along the rock dip above the shaft bottom because it was established that the ground water in the aqui¬fers flowed downward along the dip into the cone of de¬pression of the shaft. Investigations in the drillholes using the DAU-3M flowmeter described in Chapter 3 showed that all of the nine aquifers were penetrated by the time a depth of 690 m had been reached. The flowmetric information showed that aquifer numbers [1 and 2], [4, 5, and 6], and [7 and 8] had practically identical hydrogeologic characteristics; so it was decided to connect them into combined stopes and inject the grout using five stopes instead of nine. Table 9.2 shows the results of the grout injection into the aquifers. The volume of grout pumped into the separate intervals through single holes varied from 204 to 15 m3. The trend of grout consumption showed a reduction of grout consump

Jan 1, 1993

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By Jürg Künzle

Underground construction is a matter of dealing with the inherent uncertainty of subsurface geology. If the encountered conditions are less favorable than the expected ones, the execution of excavation, support, ground treatment or lining works is likely to require more or different efforts than anticipated, thereby delaying the works and increasing the costs. The 2019 first edition of the FIDIC Emerald Book model contract (FEB) addresses many of the issues to which underground works give rise, including those related to differing site conditions (DSC). This paper examines how under the FEB disputes arising from or in connection with DSC could or should be avoided.

Jun 13, 2021

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

OBJECTIVES OF RADIATION MONITORING Monitoring is a tool used in the practice of radiation protection. The primary reasons for monitoring are to reduce radiation exposures to levels that are as low as reasonably achievable and to assure that no individual receives a dose exceeding the maximum individual dose limit. The documentation of radiation doses for legal, medical, or epidemiological reasons is a subordinate function of any monitoring program. The investment in radiation monitoring programs should be guided by four criteria: (1) the detection and avoidance of unnecessary exposures, (2) the magnitude of potential health risks, (3) the determination of combined doses and risks with adequate confidence, and (4) the verification of compliance with established limits. FIRST CRITERION: DOSE REDUCTION - DETECT AND CORRECT UNNECESSARY EXPOSURES The system of dose limitation advocated by the International Commission on Radiological Protection (ICRP, 1977), and subscribed to in a broad sense by various regulatory agencies, is comprised of three essential ingredients: (1) [justification] of any practice that produces radiation doses by some commensurate net benefit, (2) [optimization] of radiation control measures by reducing doses to levels that are as low as reasonably achievable, and (3) [limitation] of individual doses to preclude inequities and [moldistribution] of risks. All too often, only the third criterion - the limitation of individual doses to prescribed regulatory limits - is explicitly addressed in everyday radiation protection programs. The emphasis of most exposure control and monitoring efforts appears to be directed toward limiting and documenting individual doses that might approach the legal limit. The first two criteria, i.e. justification and optimization, should contribute to a rationale for allocating monitoring efforts. When applied to individuals, these criteria mean the detection and elimination of unnecessary exposures. This should be a high priority of any monitoring program. Measurements should be directed toward detecting inoperative or ineffective control measures, whether or not there is a risk of exceeding the individual dose limits. The ICRP recommends a procedure that can be used effectively to reduce unnecessary exposures. A n investigation level should be established at an exposure rate substantially lower than the regulatory limit, e.g. 30% of the limit (ICRP 26, 1977, p.33). Measurements obtained during routine monitoring that exceed the investigation level are evaluated with respect to cause and potential reduction. To be effective, the evaluation results should be formally recorded and conveyed both to management and to the workers involved. Although the investigation level recommended by the ICRP is based on a fixed exposure rate or derived air concentration, an equally effective evaluation program may be based on the investigation of a percentage of all measurements. For example, one might investigate the highest 5% or a random selection of all measurements. In any case, the objective is to detect and correct situations that are producing unnecessary exposures. SECOND CRITERION: MONITOR IN PROPORTION TO THE MAGNITUDE OF RISK The ICRP criteria apply generally to all radiation exposures. However, a second priority for monitoring programs should be established on the basis of the nature of the exposures and the magnitude of the health risks involved. Current practices in radiation protection are based on dose limits to specific organs and assessment of individual exposure pathways, with little consideration of the combined doses from various pathways. Although the intent of the ICRP recommendations was to limit the total dose to each critical organ, combined doses from external and internal sources are rarely determined. The recent recommendations of the ICRP (Publ. 26, 1977) are based on the limitation of total health risk from occupational radiation exposures. Implementation of this concept would necessarily require the measurement, calculation and summation of doses and concomitant risks to all organs of the body from all exposure pathways. The U.S. Environmental Protection Agency has taken the first step toward translating the ICRP recommendations into regulations. The proposed recommendations for Federal Radiation Protection Guidance for Occupational Exposures (USEPA, 1981) include provisions for summing the risk-weighted organ doses to determine compliance with an effective whole-body dose equivalent limit. Whether or not the proposed guidance is modified before final adoption, it seems clear that some version of dose summation and combined risk limitation will be included in future regulations. With this

Jan 1, 1981

By Miguel Reyes, Mathew Girman, Chenming Zhou

Modern smart mining increasingly depends on sophisticated electrical and electronic systems for improved safety and productivity. With more electronic systems being introduced underground, the mining industry faces electromagnetic compatibility (EMC) issues caused by electromagnetic energy emitted by one device adversely impacting the normal function of another. This paper provides an overview of EMC and electromagnetic interference (EMI) research for underground mining, including a review of EMI in other industries applicable to mining, published EMI research pertaining to mining applications, representative EMI incidences, related EMI legislation in mining, and mitigation strategies.

Jan 3, 2022

By Richard E. Gray

Virtually all structures show some signs of distress due to deterioration of the building components, to changed loads, or to changed support conditions. Changed support conditions result from ground movements. In mining regions many cases of structural distress are attributed to mining without considering alternative causes. This is particularly true of coal mining since it occurs under extensive areas. Coal mining is estimated to have already undermined more than eight million acres and may eventually undermine 40 million acres in the United States (HRB Singer, Inc., 1977). Other nonmetal and metal underground mines impact much smaller areas. Although it is sometimes difficult, even with careful study, to identify the actual cause of damage, persons responsible for underground coal mining should at least be aware of possible causes of building stress other than mine subsidence. This paper presents information on distress to structures and briefly reviews a number of causes of ground movements other than subsidence: Mass movements, dissolution, erosion, frost action, shrinking and swelling, yield into excavations and compressibility

Jan 1, 1986

By R. J. Hickson

The giant El Abra copper mine project under development in Northern Chile will come on stream in early 1997 at a production rate of 500 million pounds of cathode copper annually. Ownership is 51 % Cyprus Amax and 49% Codelco. Cyprus Amax has construction responsibility. Total project cost is $1050 million. El Abra will incorporate latest operational technology with labor efficient practices to achieve world class productivity levels and low initial cash costs of about US $0.35/lb copper. Development procedures for the almost 800 million ton oxide deposit, as well as the hydrometallurgical processes selected for recovery of the copper values are discussed. Construction costs and pertinent technical data are shown.

Jan 1, 1996

By R. M. Wilson

Concentrating plants, in common with other types of industrial plants, cannot operate without lectric power. The elctric distribution system and utilization equipment; therefore, must be carefully considered in all phases of plant design. Two important aspects of proper distribution and usage of electric power are the selection of voltage levels and the methods of system grounding. These are not necessarily the most important design considerations, but are perhaps more controversial than other major points, Modern plants demand increasing amounts of power which, since electric power is the product of voltage and current means higher voltages or currents. Higher voltages require more insulation, higher currents more conductor. The equipment designer?s problem is to obtain in his transformer, cable, switchgear, controller, motor, etc a balance of insulation and conductor to obtain a satisfactory design at lowest cost. To provide the most economical system, both in initial and operating costs requires the system designer to select the proper voltage level. Adequate voltage also permits expansion to meet future requirements, and results in better operation of utilization equipment, Relatively little advancement has been made in recent years in improving conductors; however, great progress has been made in improving insulation. Thus modern plants, in general, now find it more economical to use higher voltages than they did previously. For example plants which only a few years ago would have used 2400 volts as a system voltage often find nowdays that 4160 volts is their proper choice. If the plant requires 10,000 kva br more, then an even higher voltage, such as 13,800 volts, will prove economical. However, for the average concentration plant, with less than 10,000 kva demand, the choice of distribution voltages is between 2400 and 4160 volts, and 480 volts will be used for the low voltage utilization system.

Jan 1, 1958

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By Arthur Miller

Most of the production of copper in the United States comes from a few large companies. Often overlooked, however, are the more numerous small mining operations, which collectively produce a significant portion of the nation's copper. The objective of this paper is to describe the operations of a small mining company - Ranchers Exploration and Development Corporation - how it views its place in this industry of giants, how it exploits the advantages offered by its relatively small size, and how it protects itself from the hazards being small introduces. Environment is, of course, a critical factor for such a company because it does not have the resources which help large companies weather periods of financial stress. Ideally, this environment is characterized by a heal thy economy, strong product demand, relatively stable prices , adequate grades and tonnages of ore commensurate with depth and over-burden, ready access to utilities, a dependable labor pool, and suitable technical "know how". When the environment is right, properties which were previously uneconomical to operate attract the attention of companies whose primary interest is a return on investment commensurate with risk over a reasonable period of time. Naturally, the amount of the investment and the duration of operation determines the size of the company which would be interested in such a venture. Such is the case with Ranchers Bluebird Mine at Miami, Arizona - a small property operated by a small company in a favorable economic environment.

Jan 1, 1967

By David Court, Rab Brown

The paper discusses the work in progress on the construction of the extension of the High Speed Rail line from the Channel Tunnel into the centre of London UK known as the “Channel Tunnel Rail Link” (CTRL), and particularly on contract 250 which involves the construction of two 5.3Km tunnels 7.15m diameter constructed with two EPB convertible tunnelling machines underneath the densely populated area of East London. In addition the paper will look at an innovative Alliance that has been formed between the Contractors and the Client’s Engineer involved in the construction of the London Tunnel Contracts

Jan 1, 2003

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By Derek du Preez, Andrew Hall, Timothy M. Pelech

Net Present Value (NPV) derived from Discounted Cash Flow (DCF) analysis remains the dominant metric for evaluating mining projects despite its well-documented inability to capture managerial flexibility under uncertainty. DCF assumes that all risks are perfectly priced by financial markets. This is an unlikely assumption for volatile commodity prices, geological variability, or the array of mining technical and operational risks present on all mine sites. Real Options Analysis (ROA) was developed to remedy this limitation by explicitly valuing the ability of managers to defer, expand, scale, switch, or abandon investments as new information emerges, and to capture upside and mitigate downside risks. While ROA is philosophically correct and routinely shows an uplift in project value compared with DCF, its practical application at industrial scale is severely constrained, ROA faces the reality of a combinatorial explosion in complexity of decision trees, Monte Carlo simulations and other models required when multiple interdependent or sequential options exist across numerous mining zones and time periods. The AMC Hill of Value® (HoV) process adopts the same intellectual foundation as ROA, that flexibility has economic value, but operationalizes it through a far more robust and scalable architecture. It is built on parametric relationships, rapid scheduling, and multi-objective evolutionary optimisation. HoV can evaluate millions of compound, interdependent real options in a single optimisation run, delivering resilient, adaptive strategies that preserve managerial flexibility while simultaneously optimising NPV, mine life, risk exposure, and other corporate objectives. This paper demonstrates that HoV is the practical, industrial-scale embodiment of real options thinking in mining: it discovers, ranks, and translates the most valuable real options into strategic mine plans, overcoming the scalability barriers that have prevented widespread adoption of classical ROA.

Feb 22, 2026