Search Documents

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By Ali Behrad Vakylabad, Esmaeel Darezereshki, Babak Koohestani

As a by-product of the steelmaking industry rich in iron and zinc, electric arc furnace dust (EAFD) landfill disposal is restricted in many countries due to the metal lixiviation risks. Several approaches have been examined to recycle or reuse EAFD. Hydrometallurgical methods mainly include the preparation of pregnant acid leached solution (PLS) using inorganic acids followed by selective metal recovery using different methods. We herein proposed a hydrometallurgical process initiated by acid leaching and finalized by thermal treatment to produce nano-ZnO from EAFD. At the condition of this study, only 67% of zinc was leached by sulfuric acid from EAFD into PLS while 98% of surplus leached iron was removed through precipitation by sodium hydroxide. Additional purification of iron removed PLS was accomplished using di-2 ethylhexyl phosphoric acid to extract Zn+2. The addition of ammonium hydroxide to purified PLS provided (Zn(OH)2)3(ZnSO4)(H2O)5 as the final precursor for nano-ZnO that ultimately transformed to nano-ZnO (60 ± 6 nm particle size) at 850 °C. The achieved results were scrutinized through various tests and analyses including TEM, XRD, SEM, EDS, FTIR, and TGA.

Mar 10, 2021

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By C. I. Basilio

The mechanisms involved in the adsorption of modified thiol-type collectors on sulfide minerals have been investigated in the present work. These collectors belong to the broad classes of thionocarbamates, thioureas, thiophosphates and thiophosphinates. They differ significantly from the traditionally used thiol-type collectors, such as xanthates and dithiophosphates, in terms of structural features that involve either the introduction of an additional oxygen donor or the alteration of electron densities on donor atoms. Electrochemical studies suggest that the adsorption of these classes of collectors is probably the result of a coupled reaction of the EC-type, involving an initial electron transfer step (E), followed immediately by a chemical reaction (C). Thus, the overall adsorption process is controlled by both the E, and pK of the system. The role of structural features in changing the interaction of the donor atoms with sulfide minerals is also discussed.

Jan 1, 1991

By W. J. Douglas

The mine manager in today's environment is faced with a wide variety of problems and challenges which must be addressed if efficient and profitable operations are to be achieved. Expansion of operations has, in many instances, resulted in inexperienced work crews, face supervisors, and superintendents. The complexities of a mining system preclude rapid movement through the learning curve for moat personnel. The management of production suffers both from this inexperience and the lack of standard procedures and methods for planning, schedul ing and analyzing production systems. The lack of visibility of information, as well as of the operations themselves, due to their remoteness, adds to the problem of production management.

Jan 1, 1980

By S. C. Gaillard

Tailings are made of ground rock that is left over from removing valuable minerals. The tailings are usually fine particles that cause environmental issues for storage and disposal. Disposal of tailings is a growing concern, as more tailings are produced from the increasing demand for mined material (ITRC, 2008). This project proposes a way to convert the mine waste to a useful product. Tailings were selected from a South Carolina crushed stone quarry, the products of which are used for road beds, sidewalks, asphalt and driveways. These tailings were processed to generate synthetic aggregates for construction applications. The synthetic aggregate creates a product that could be used for many purposes, including aggregate for sidewalks, driveways, roads and building materials. Testing methods followed the North Carolina Department of Transportation (NCDOT) guidelines for physical testing of coarse natural aggregate, which are sieve analysis, Los Angeles abrasion, absorption, specific gravity and soundness test. The synthetic aggregate produced passed all tests for NCDOT and, in some instances, rated better than a natural aggregate. Using the tailings from the crushed stone and mining industry would convert the waste into a valuable, marketable product.

Jan 1, 2013

By J. F. Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch mine in West Virginia, where 29 miners lost their lives. The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Feb 23, 2014

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

By A. Anttila, S. Persson

The grinding mill is probably the most common unit operation in mineral processing. There is, however, much that can still be done in the way of optimization. This paper discusses the results of a well-controlled pilot-scale test in which the performance of a tumbling mill equipped with a conventional rubber lining and lifter bars was compared to a tumbling mill equipped with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14% more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case, grinding with a -20-mm ball charge required 26% less grinding energy than grinding with a -30-mm ball charge. The energy savings can, in most cases, be converted to an increase in capacity. The wear of the grinding media is difficult to assess over a short test period, but the results suggest that the wear is somewhat less when a smooth lining is used. A determination of the wear of the linings was not included in this study, but it is generally accepted that the use of magnetic linings reduces the lining costs dramatically. Computer simulation using the Millsoft code developed by Mishra et al. confirms and explains the increased effectiveness of comminution when a smooth lining and smaller grinding balls are used.

Jan 1, 2000

By John A. Meech

In many multiple-sulphide ore flotation processes, it is desirable to concentrate each of the various valuable minerals into separate products. Although there are a variety of techniques and chemicals which can be employed to produce efficient separation, two basic types of flotation circuits are used: The Differential Flotation Circuit and the Bulk/Selective Flotation Circuit. Figure I depicts these two circuits in their most simplified form for the production of two concentrates and one tailing product. If three or more valuable minerals are present in an ore, a variety of combinations or extensions of these two basic flowsheets may be used. There are many examples of the successful application of both circuit types with ores containing similar minerals. Each ore must be tested individually to decide on which circuit is best. However, the following general statements can be made: 1) The differential circuit will have higher capital and operating costs than will the bulk/selective circuit due to higher rougher capacity requirement. 2) The differential circuit will achieve better separation than will the bulk/selective circuit since it is usually easier to reactivate a depressed mineral than it is to depress an already active mineral. If the deactivation problem with the bulk/selective circuit . . in can be overcome, there is a clear economic argument for its use

Jan 1, 1977

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998

By J. L. Fuller

Mine ventilation surveys were conducted by Technical Support engineers during June 1987 and September 1989 at the Dutch Creek Hine. The mine is located near Redstone, Colorado and is operated by Mid-Continent Resources, Inc. Following completion of the initial survey, several recommended improvements were incorporated into the ventilation system by mine personnel. The second survey permitted documentation of the effects of those changes on the ventilation system performance. This paper describes the processes involved in the implementation of the recommended changes. The substantial improvements in system efficiency and reduced operating costs are also described.

Jan 1, 1991

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

By G. S. Austin

New Mexico produced 83% of domestic potash and 27% of domestic consumption in 1992. The potash industry of New Mexico produces sylvite (KCI), langbeinite (K2SO4-2Mg(SO4)2), and artificial K2SO4. Average sylvite grade in New Mexico today is about 14%. The average grade of langbeinite is 8-10% Kp. Commercial potash occurs in the middle or McNutt Member of the Salado Formation (Upper Permian Ochoan Series). The 120-m-thick McNutt Member dips about 1° east and contains 11 of 12 potential ore zones in the Salado. The mineralogy and proportion of clay minerals, up to 7% of the ore, influence optimum milling procedures and ore grade cutoff.

Jan 1, 1994

By J. Drelich

The flotation limit of fine particles has been re-examined based on the effect of bubble size on contact angle, and a new surface chemistry-limited relationship describing the minimum particle size which can be floated is proposed. In this analysis the critical value of bubble-solid contact radius (re) for which there is no effective attachment between particle and bubble has to be determined. The values of re determined by extrapolation of our experimental data for contact angle versus bubble-solid contact diameter permit the prediction of the flotation limit of methylated quartz particles, with fraction-al coverage of trimethylsilyl groups from 0.07 to 0.51. The limit of fine particle flotation as determined by this theoretical approach agrees well with experimental data reported in the literature.

Jan 1, 1994

By K. S. Fraser, R. Frischmuth

High temperature pressure oxidation (>190°C) is a wellrecognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulfide ores and concentrates. The pressure oxidation of refractory gold ores was first commercially applied in 1985, at Homestake Mining Company’s McLaughlin mine in the United States. Since that time numerous refractory gold and other high temperature pressure oxidation facilities have been built throughout the world. The design of each facility was met with unique challenges and opportunities which have led to an array of plant configurations, pressure oxidation autoclave sizes, and sulfide oxidation capacities. This paper presents a historical review of high temperature pressure oxidation operations and current projects in execution with a focus on the autoclave vessel design, circuit configuration, and unit sulfide oxidation capacity as a basis for characterization and comparison.

Mar 2, 2022

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985