Search Documents

By D. E. Scheck

A computer-aided blast design consultant system has been developed. The software consists of two modules: one uses theoretical and empirical formulae and procedures to design a blast based on user supplied geological and mechanical data, while the other is an expert system that analyzes blast vibration problems and recommends remedial action using knowledge based rules. The system is currently undergoing field evaluation.

Jan 1, 1987

By G. M. Bentel, G. E. Blight

The environmentally acceptable disposal of fine-particled mining and industrial wastes by the formation of hydraulic- fill slimes dams is becoming an increasingly important aspect of the total mining endeavour. Relatively little is known of the behaviour of waste slurries during deposition. This paper describes and analyses the following aspects of slurry behaviour: (i) the relationship between viscosity, shear strength, and water content, (ii) the slope assumed by a thickened slurry, (iii) particle-size sorting on a hydraulicfill beach, (iv) gradients of hydraulic-fill beaches, and (v) internal erosion during the deposition of slurry. v083n04p073.pdf

Jan 1, 1983

By H. E. Cross

Metallurgical considerations in the automation of gold-recovery plants By H. E. CROSS. Pr. Eng., B.Sc. (Eng.) Hons. (Fellow) The advantages of the automation of gold-recovery plants are examined. The various sections of a gold-recovery plant are analysed, and the extent to which instrumentation can usefully be employed is described. INTRODUCTION The scope of this paper is restricted to the ore-treatment and recovery plants on Witwatersrand gold mines. To extend the field to plants that process base metals and industrial minerals would result in a paper that would be too lengthy. However, the subject matter of this paper is applicable to most mineraldressing and recovery plants and will, it is hoped, be a foundation on which to build somewhat more sophisticated control systems required in the base-metals field.

By S. Budavari

On the one-hundredth anniversary of the founding of the South African School of Mines, this paper presents a historical review of the tertiary mining education carried out by the School of Mines in Kimberley and the subsequent institutions in Johannesburg. In addition to recording and evaluating a century of mining education, it describes the current activities of the Department of Mining Engineering at the University of the Witwatersrand, which is believed to be the natural successor to the School of Mines. The comparison of earlier and contemporary academic mining activities reflects a gradual transition from the educational philosophy and objectives of a school of mines to those of a modem university department. In the conclusions, some aspects of the educational effort expended during the past hundred years are briefly highlighted.

Jan 1, 1996

By R F. Sandenbergh, Y Wei

The flotation separation of the Rosh Pinah ore into lead and zinc concentrates are based on the selective flotation of the lead containing minerals followed by the activation and recovery of the zinc sulfides. In the present work the influence of the composition of the water on the selective flotation of the lead containing minerals is reviewed and the results given of the laboratory investigation of the influence of activating species such as silver, lead and copper, on the selective recovery of lead minerals from the Rosh Pinah ore. It was found that it was difficult to prevent the activation of the sphalerite by the metal species in solution in the absence of cyanide, and that colloidal precipitates most probably also serves as a significant carrier of these activators in the flotation circuit. Removal of heavy metal species from the solution by means of an adsorbent is possible, but most probably not practical.

Jan 1, 2007

By C. L. Workman-Davies

Noise is a form of pollution arising mainly from the activities of man. One such activity is mining, in which man, as in many of his other activities, uses machinery of various kinds to achieve safe, healthy, and economic production. Trackless mining makes use of an advanced state of technology over that required In traditional mining methods. One of the advantages of the former, as distinct from any disadvantages it may have, is a reduction in noise levels, the number of people exposed to noise, and the duration of their exposure to noise. This paper briefly examines why noise is a problem and what various countries are doing about it in terms of standards, codes of practice, and regulations. It also investigates the extent to which noise is a problem in mining and how trackless mining alleviates this problem. The question is then posed as to whether South Africa is not setting too high a standard at this stage of its national development by comparison with what is being done by other, more-advanced countries.

Jan 1, 1989

By P. M. Swash

A mineralogical investigation of the main causes of refractoriness of some metalurgicaly complex gold ores in South Africa is reported. It is shown that this refractoriness is related to the presence of submicroscopic gold, carbonaceous material, pyrhotite, and base-metal sulphides. Gold ores can be classified according to their content of these components. Electron-microprobe analysis shows that gold occurs in arsenopyrite and pyrite, the gold contents of which can be up to 2700 gft. The gold and arsenic contents of these minerals are closely corelated. Furthermore, within zoned arsenopyrite grains, the concentration of gold closely folows that of arsenic. Mossbauer spectroscopy caried out on samples of concentrate from the Barberton area indicates that the submicroscopic gold within the sulphides is in a non-metalic form. The mineralogical examination of beneficiation products is important, since it sheds light on some fundamental aspects of the behaviour of the ore and gangue components during milling and flotation. Such basic information will lead ultimately to a better understanding of the problems in the beneficiation of these ores. Investigations have shown that the overmiling of the auriferous arsenopyrite and the disseminated nature of the sulphide mineralization are the main problems during beneficiation.

Jan 1, 1988

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMC's (now BHP Billiton's) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

By R. Tinsley

Project-finance risk assessment is mature and approached systematically. Mining industry due diligence remains fragmented with specialists addressing different aspects of the project such as reserves/JORC, environmental impact, commodity market, even financial analysis/ modelling. Each professional has a natural tendency to believe that the risk factors they have examined are the key ones necessary to be reviewed, as if their review will stand in isolation from others in the way a project materialises. By first laying out the project risk categories and risk matrices, this paper examines the due diligence process with a keen eye to the risk assessment and overlap/interaction. Some cross fertilisation of due diligence techniques from other industry sectors is placed into the mining context. Six case studies are then presented with regards to due diligence features in each project's feasibility review or financial information/ offering memorandum. A power case first shows the differences between the due diligence expectations of banks versus bond financings. Then some Australian and Indonesian mining development cases are analysed to see the due diligence learning points. Some of these were project/due diligence failures. The conclusion focuses on the value of a systematic risk assessment for project evaluation, all from the project-finance perspective.

Jan 1, 2007

By L. A. Vermeulen, D. D. Howat

Extensive work was done previously on the wear of grinding media and on the comminution processes operative in bal milling based on the determination of the number-size and mass-size distributions of samples of balls taken from bal mils by a specially designed device. Proof that a sample is as nearly representative as possible of the whole mass of material from which it is drawn is usually extremely difficult. This paper reports a special case in which a direct comparison was made between the number-size and mass-size distributions obtained from a sample drawn from a mil and those from the whole bal charge emptied from the mil. Exposure of the internal defects of the grinding balls caused them to develop irregular shapes after wear had reduced their diameters by about 50 per cent. As a result of the marked change in the morphology of the grinding components, an anomaly was observed between the proportion of small components collected by the sampler and that determined in the total charge. Except for this anomaly, a marked similarity was found in the data relating to the larger components in the sample and the total charge, indicating that the sample obtained by the procedure outlined is representative of the mass of the grinding charge in a mill.

Jan 1, 1989

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 19th August, 1981. Dr P. R. Jochens (President) was in the chair and declared the meeting open at 4.05 p.m. This account of the proceedings includes only those matters that are not reported under the heading `Annual report and accounts' elsewhere in this issue. Confirmation of the Minutes The minutes of the last Annual General Meeting, which was held on 27th August, 1980, were confirmed as pub¬lished in the September issue of the Journal. Welcome President: I extend a sincere welcome to you all, especially to the following distinguished guests: Mr L. W. P. van den Bosch, President of the Chamber of Mines, and Mrs van den Bosch; Mr J. G. Kirchner, Government Mining Engineer, and Mrs Kirchner; Dr William Ble¬loch; Dr L. Alberts, President of the National Institute for Metallurgy, and Mrs Alberts; Dr C. F. Habis, Presi¬dent of the CSIR, and Mrs Habis; Dr P. J. Hugo, Chief Director of the Minerals Bureau, and Mrs Hugo; Mr D. N. Stuart, General Manager of the Chamber of Mines, and Mrs. Stuart; the Presidents and representatives of other Institutes and their wives; and Honorary Life Fellows of our Institute and their wives.

Jan 1, 1981

By M. S. Janssen, J. L. Taylor, M. A. Ford, E. B. Viljoen, H. A. Simonsen

The Stilfontein and Buffelsfontein Gold Mines, near Klerksdorp in the Transvaal, had accumulated a large amount of uranium-containing residue and, when the price of uranium rose in the 1970s, consideration was given to the possible recovery of this uranium. Preliminary tests showed that concentration of the uranium prior to leaching would not be economic. However, the pyrite in the residue could be concentrated by flotation, and the flotation concentrate could be roasted to pro¬vide both enough acid for leaching the uranium and a calcine from which the gold could be recovered. The feasibility study showed that a uranium operation of 270 kt per month would be most economically attrac¬tive, and a plant of that size was accordingly designed and built. In the first six years of its existence, the plant treated over 20 Mt of residue and produced about 3,5 kt of uranium oxide. During that time, the plant was con¬tinually being improved to make it more reliable and cost-efficient. This paper analyses the operation of the plant during its first six years from the viewpoints of its mechanical, process, and economic performance. The criteria on which the selection of the process was based are reviewed and compared with the actual performance of the plant, emphasis being placed on the leaching, solid-liquid separation, recovery, and purification stages.

Jan 1, 1987

By J. D. Austin

Currency fluctuations affect the rand revenues of all exports of mineral commodities, as well as influencing their price on local markets. Of the more than 50 mineral commodities produced by South Africa, about 75 per cent derive 40 to 100 per cent of their revenues from exports. . Although supply and demand are largely beyond its control, management can maximize its revenues despite fluctuating overseas prices and exchange rates by using the right market at the right time. Management can operate in the futures markets, which involve a specific commitment to deliver a specific quantity of a standardized commodity at a set time in the future and at a price that is determined on a futures exchange in open auction; or management can use the options market, in which a producer can insure against the risk of a falling price by taking out a put-option, which gives the holder the right (but not the obligation) to sell the commodity at a stated price at an agreed time in the future. In the forward markets, management has three available tools; forward currency transactions, trading of currency options, and money market hedges. Revenues, currencies of exchange earnings, purchasing power of the rand, and world price trends are shown in over 40 diagrams and tables for the main mineral commodities produced in South Africa.

Jan 1, 1984

By Alastair S. Macfarlane

The Mineral Resource that a mining company has access to, represents the majority of the embedded value that exists within the company, as well as the competitive advantage that the company has over its peers. However the real value is only realised once effective mining plans have been put in place, which optimise the extraction of the Resource, and add measurable value to the Company. The concept of Mineral Resource Management has been developed in South Africa, to ensure this optimisation happens in an integrated and quantifiable manner, such that value is added and risk is reduced, resulting in bottom line improvement for the stakeholders of the business. This paper describes the process of Mineral Resource Management, and draws on successes and failures of various companies, to illustrate how it should be implemented, and what measures should be put in place to ensure its success. This requires a fundamental re-appraisal of the way in which mining companies plan and execute their businesses, and focuses attention on real value adding activities and behaviour through the use of Economic Value Added as an appropriate metric by which to measure real value and risk. Specifically, the paper focuses on these aspects as applied to planning models and processes, exploration activity and risk management, to ensure operational and project success.

Jan 1, 2007

British Mining Fields, by J. E. Metcalf. Published by the Institution of Mining and Metallurgy, London, 1969. Price 50s. (Students, 30s.). A 100 years or so ago Britain's mining industry led the world in the production of coal and base metals. Although she still maintains a sizeable-and, under the circumstances, remarkably progressive-coal mining industry, her production of most other base minerals has long since been dwarfed by mining fields in the Americas Africa, Australia and the U.S.S.R. Nevertheless the story of mining in Britain is of wider interest than the present scale of operations there might suggest, if only because the domestic British mining industry has in terms of finance, technology and manpower been the fons et origo of many highly productive mining fields outside Britain, including the Witwatersrand goldfields. British Mining Fields was published by the Institute of Mining and Metallurgy to give delegates attending the Ninth Commonwealth Mining and Metallurgical Conference a succinct account of mining in Britain. The main emphasis is on underground mining of base minerals-treated regionally-with separate chapters on coal and gypsum. The author strikes an admirable balance between historical aspects, geological origin and environment of ore deposits, mining methods and economic factors, and provides a few key references for those who wish to make deeper studies. This is exactly the sort of booklet one often wishes were available on South African mining.

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By Dr Peter Laxen

Dr Peter Laxen, the Mintek Consultant on gold and uranium, has won the 1982 award of the Percy Fox Foundation. The presentation was made by the Minster of Finance, Mr Owen Horwood, at a banquet on 6 March.

Jan 1, 1982

By D. R. Hardman

South Africa is the third-largest supplier of coal on the world's export markets after Australia and the USA, and the second-largest supplier of bituminous steam coal following Australia. There are many Similarities between the coal industries of South Africa and those of Australia and the USA, in contrast to the coal industries in Europe. For South Africa to maintain a competitive position on the export markets, it must continue to compete against these two countries. It is therefore important that the performance of the loca1 coal industry should against that of the Australian and US coal industries. Although financial performance is the major criterion, financial information is not easily obtained, and the paper therefore uses employee productivity in the form of tonnes per man year as a means of comparison. The paper reviews recent trends in the level of production and numbers of employees prior to review1ng the productivity. The influence on productivity of some mining methods is highlighted. It is realized that published information (information available within the public domain) can contain anomalies, but every effort is made to compare data of a similar type. Notwithstanding possible inaccuracies, it is shown that South African coal-De productivity lags far behind that of Australia and the USA. The significance of the difference is that the South African coal industry is able to apply overseas practices and procedures that have been shown to give improved performance, and that the increased use of more productive extraction techniques has limited application.

Jan 1, 1996

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.