Search Documents

By A. K. Haines

The status of the South African research and development programme on continuous ion exchange, which was aimed at the technical and economic assessment of that process for the recovery of uranium, is reviewed. The first phase of this programme, which has now been completed, involved development investigations on various pilot plants and culminated in the successful operation of a large-scale demonstration plant and the incorporation of the system in a number of new South African uranium plants. This account highlights the engineering aspects and the design fo the system, its adaptation to process flowsheets, and plans for future development.

Jan 1, 1978

By J. L. Taylor, E. N. Lawson, Hulse. G. A.

It is generally recognized that a large proportion of the gold remaining in the residues from metallurgical plants on the Witwatersrand is occluded in pyrite. The conventional flotation-roasting process typically recovers approximately 40 per cent of this gold. The process described here is an unconventional route involving bacterial oxidation, which can achieve a gold recovery of approximately80 per cent. The paper describes tests carried out in the laboratory, as well as on a slimes dam. The results show that recovery of gold can be noticeably enhanced through the use of bacteria under conditions of controlled pH, moisture, and aeration. Biological oxidation of the pyrite releases the occluded gold, which then becomes amenable cyanidation.

Jan 1, 1990

By J. J. van Vuuren

Pipe-stick support in deep-level gold mines is first described and illustrated, a pipe-stick being a mine pole trimmed to the required size and sleeved by a pipe. An account is then given of an investigation into this form of support that involved load-compression tests in a 1000-ton press, tests in a rapid loading machine simulating rock-burst conditions, a study of the load-compression behaviour of pipesticks installed underground, and a cost evaluation. Pipe-stick support was found to be very effective on the face and to cost less than conventional matpacks.

Jan 1, 1979

By S. A. C. Liedberg, M. H. Fricker

The conference was divided into a total of 12 different sessions. Apart from the keynote addresses, the papers covered many aspects of open-pit mining, from mine design and blasting techniques to mining operations and equipment, as well as water management and rehabilitation. A number of case studies were also presented. Most of the 68 papers originated from Australia; however, presentations were also made by representatives from Chile, Indonesia, Papua New Guinea, and South Africa. The keynote papers dealt with subjects such as the economics of open pits, project planning of a new large copper deposit, management principles, and rehabilitation strategies.

Jan 1, 1993

By P. Geldenhuys, D. J. C. Taylor, D. C. Page

This paper gives a technical review of the history, occurrence, mining, and metallurgy of iron in South Africa. The reserves of iron ore worldwide and in South Africa are reviewed, and potential new developments In the iron-and-steel industry in South Africa are examined. The paper concludes that the exploitation of lower-grade iron deposits will probably supplement the reserves of high-grade hematite ore in the distant future, and that, accepting this scenario. South Africa will be well placed to provide iron ore for its expected internal steel requirements, as well as supplying quality Iron ore for the export market.

Jan 1, 1988

By A. M. Starfield

SYNOPSIS A description is given of a new computer programme that has been developed for the rapid computation of the changes in temperature and humidity of air passing through mine airways. The programme enables the ventilation engineer to calculate air temperature increases along airways with an ease that is comparable with that of looking up a set of graphs or tables in an engineering hand-book. The pertinent information for a particular airway can be fed to the computer either on a standard punched card, or by typing directly into the computer at a remote terminal teletype unit.

By I. M. W. Preston

A new shaft system was required to replace stope face for the North Section of Harmony Mine and to allow for systematic opening up of the North Eastern Section. Owing to the economic circumstances at the time the project started, it became vital to alter the original planning and to sink the service shaft first. The MATLA coal-sinking headgear, a novel presinking arrangement, allowed sinking to continue to 108 m concurrently with the erection of the permanent sinking headgear and sinking winders. It is estimated that this arrangement resulted in a saving of two months on the overall project.

Jan 1, 1983

By T. Copland

"The decreasing availability of resources amenable to surface operations has led to increasing numbers of underground mines, with trends indicating this will continue into the future. As a result, there is a need for additional optimization processes and techniques for underground mines, with many analogous methods having already been developed for surface mining. Current methods for design and optimization of stope boundary selection and scheduling mainly involve heuristic methods which focus on a single lever. Individual optimality may be approached, but globally optimal results can be obtained only by an integrated, rigorous approach. In this paper we review previous methodologies for stope boundary selection and medium- to long-term scheduling and highlight the need for an integrated approach. Previous integrated approaches are reviewed and an improved modelling system proposed for shorter solution times and greater applicability to mining situations. Randomly generated data-sets for gold-copper mineralization are used to investigate the model performance, describing solution time as a function of data complexity.IntroductionThe increasing need for mineral resources is driving an increase in underground mines. Lower grade mineralization with larger amounts of overburden is becoming economically viable due to technological advances; however, the software and tools available for strategic underground mine planning are not well developed. Advances in the methods used to determine underground layouts and scheduling must occur to ensure underground mining is as optimized as open pit operations, as underground mining involves many more technical restrictions.The process of determining stope boundaries and scheduling is an example of an aspect of underground mining amenable to optimization (Topal and Sens, 2010). The current industry standard for medium- and long-term planning for sublevel stoping (SLS) is to exclusively determine stope outlines and then determine an appropriate sequence and schedule accordingly. This process violates the concept of optimality as integrating the constraints imposed by pre-determining stope outlines does not allow for considerations in scheduling to influence boundary planning (Ataee-Pour, 2005). An integrated planning process that combines both stope outlines and scheduling would approach the optimal solution and hence generate more value for operations. This investigation specifically deals with the underground sublevel stoping (SLS). Other underground mining methods such as block caving, sublevel caving, and room and pillar mining have unique characteristics and therefore require specific stope boundary/production scheduling considerations."

Jan 1, 2016

By D. M. C. Valbom

The introduction of new diamond sorting technologies as well as additional manufacturers I vendors, has increased the equipment selection and combinations available for recovery flowsheet design. This paper describes the methodology used and the benefits realized in the design of recovery plants by ensuring a fundamental understanding of the advantages and limitations of the technology embodied in the equipment, a comprehensive knowledge of the ore body characteristics, and the effective matching of this information in combination with operational commercial requirements.

Jan 1, 2010

By A. W. de Villiers

This paper explores the behaviour of methane in the goaf during longwall mining, together with some methods for the control of methane emissions into the goaf, the working face, and the ventilation system. Experimental work done at Twistdraai Colliery, Sasol Coal, is referred to, as well as the gas-drainage system being practised at West Cliff Colliery in New South Wales, Australia. Gas drainage is discussed briefly, and certain suggestions are made in regard to coal mining in South Africa.

Jan 1, 1989

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By D. F. Malan, W. J. Theron

Practical mining aspects should be considered when conducting pillar designs for bord-and-pillar layouts. The current methodology for pillar design will result in increasing pillar sizes with depth. This affects the extraction ratio and will result in onerous ventilation requirements when cutting large pillars. A holistic approach, including all mining engineering requirements, is required to ensure that the rock engineering designs are optimized to ensure efficient mining operations and sustainable production. Bord widths should not only be a function of the rock mass ratings, but should also be selected to fit the specifications of the mechanized equipment. The use of a ‘squat pillar’ formula for hard rock is discussed in the paper and the formula based on the exponents of the Hedley and Grant pillar formula, is explored. The effect of abutments and geological losses on average pillar stress is also explored. These factors must be considered when designing layouts at increasing depths.

Nov 27, 2024

By W. A. Hustrulid

CONTENTS PART I The theory of percussive rockdrill operation. Blow frequency Piston impact velocity and blow energy Thrust requirements Prediction of penetration rate Drillsteel life Bit wear PART II Measurements of percussive rockdrill performance Thrust-penetration rate measurements Blow frequency Piston impact velocity and blow energy Prediction of penetration rates The effects of hole diameter Thrusts applied by men Bit wear Appendix I Experimental procedure and rockdrill and drill steel specifications Appendix II Piston impact velocities and energies PART III Practical implications. Provisions of adequate thrust Conclusions INTRODUCTION In South African gold mines some 100 million tons of rock are broken each year by drilling and blasting. Only minor improvements to this method of rockbreaking have been made since the general introduction of pneumatic rockdrills for stoping 50 years ago and, more recently, of drillsteels tipped with tungsten carbide. The combined total cost of drilling and blasting amounts to almost R0,50 per ton of rock broken, which is just short of one quarter of the direct cost of stoping or development. Rockdrilling accounts for about R0,25 of the total cost of rockbreaking, of which RO,12 represents labour costs and R0,13 the cost of drillsteels, rockdrill spares and power. Mine air compressors use over 7 X 108 kWh of electric energy a year, amounting to 7 percent of the total electric power used by the gold mining industry. The efficiency of percussive rockdrilling is, therefore, of considerable significance to mining costs. Over the past four years the Mining Research Laboratory of the Chamber of Mines of S.A. has been engaged in experimental studies of percussive drilling. These experiments were conducted at test sites on Robinson Deep Gold Mine and Vlakfontein Gold Mine, made available by Gold Fields of South Africa, Limited. Three rockdrills, designated types A, Band C, of different manufacture, were used in the experiments which involved the measurement of the following operating characteristics: 1. Throttle air pressure 2. Applied thrust 3. Penetration rate 4. Air consumption 5. Blows per minute 6. Drill steel revolutions per minute. The results of these investigations are presented in three parts. Part I, "The theory of percussive rockdrill operation" which provides a concise, mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions and operating conditions, and an analysis of the bit and gauge wear of drillsteels. Part II, "Measurements of percussive rockdrill performance" in which the experimental results are presented in terms of thrust-penetration rate curves at different throttle air pressures and throttle pressure-air consumption curves, which are shown to agree well with the predictions of theory. In addition, data relating gauge wear on the drillsteel and penetration rate to the distance drilled are discussed. Part III, "Practical implications" in which an analysis of the status of thrusting devices is made and the benefits that would derive from using uptimum thrusts are discussed.

By M. Tang, X. Tong

"SynopsisSlime coating is one of the most common ways for serpentines to contaminate metallic mineral concentrates during traditional flotation of coarse sulphide particles. This could pose quite a complicated and challenging problem in the case of some types of low-grade and finely disseminated Cu-Ni ores bearing high serpentine contents. This is the case for the copper and nickel sulphides from the Yunnan Mine, China. Previous batch flotation tests of this ore resulted in satisfactory recoveries of 86.92% Cu, 54.92% Ni, and 74.73% Pt+Pd, and concentrate grades of 4.02% Cu, 3.24% Ni, and 76.61 g/t Pt+Pd. However, the MgO content in these concentrates was more than 19%. In the current study, microflotation tests and settling rate tests were introduced to investigate the effects of a combination of strong collectors (a 2:1 weight ratio of butyl xanthate and butyl ammonium dithophosphate) on entrainment of serpentines in metallic mineral concentrate, as well as visual observations of the concentrates in suspension using still photography. All test results indicated the presence of serpentines entrapped in the hydrophobic flocs that resulted from these collectors, even with the use of effective gangue depressants. These strong collectors are used to flocculate the ultra-fine sulphides by forming loose and ‘fluffy’ hydrophobic flocs. However, these hydrophobic flocs may also be able to load or entrap some serpentine slimes into the concentrate, and this entrained serpentine could be harder to remove by using depressants or intensified conditioning than serpentine slime coating on the particle surfaces.IntroductionSerpentine minerals, which have the generalized composition (Mg,Fe)3Si2O5(OH)4, can be easy to crush and grind due to their convoluted and bent layered structures. These serpentines can hinder the enrichment of some metallic minerals and dilute their concentrates by entrainment during flotation. The resulting high pulp viscosities, slime coatings, and high content of dissolved ions adversely affect the flotation recoveries of copper and nickel sulphides, and high levels of MgO entrained in the concentrates lead to heavy penalties from smelters. Since the quality of nickel flotation concentrate depends heavily on its MgO content (generally less than 6–7% for No.1 or 2 grade nickel concentrate according to the standard requirement from National Nonferrous Industry), reducing the entrainment of serpentine during flotation is becoming more and more pressing. Previous research has focused on the collectors and depressants that are commonly used in copper-nickel flotation, as well as their interaction mechanisms."

Jan 1, 2015

By D. Vogt

"Rock has been cut in the process of mining since before the invention of explosives. Today, we seek to return to cutting to reap the benefits of continuous operations for South African underground hard-rock mines, to improve speed of access to the orebody, and to improve the efficiency of mining operations.Development of new technology fits within a framework of engineering knowledge. By understanding the characteristics of the rock, the tools we use to cut it with, and the history of mining and rock cutting, we can see the genesis of the road-header, the longwall, and the continuous miner, all drag bit cutters. They have emerged as the solutions of choice for underground mining of softer materials such as coal and potash. In hard rock, the challenges are the forces required to break the rock, and the wear of the tools caused by the rock’s abrasiveness. Only disc cutters currently handle the challenges, and even then, often not economically. New materials like thermally stable diamond composite will help, as will combinations of mechanical cutters and other methods such as high-pressure water or high temperatures.It is not clear what will emerge as the consensus technique for hardrock cutting. Experience teaches that development is expensive and the market is small. Will mining companies partner with equipment developers to make the technological leap? Or will the solution come from a systems approach, not considered here?IntroductionBlasting is the dominant method of breaking rock for the purposes of mining. When used underground, blasting is part of a batch process. If rock can be cut rather than blasted, mining can become continuous, leading to process and efficiency improvements.Coal produced from underground mines is now predominantly excavated using mechanical means, but underground hard rock is still broken primarily by explosives.This paper traces the history of rock cutting, reviews the main physical processes that are or could be used, and comments on the future. It is written from the perspective of narrow-stope hard-rock mining typical of South African gold and platinum mines."

Jan 1, 2016

By M. David

This paper addresses the problem of technological transfer in geostatistics. Expert systems have become popular in certain fields because the needs of the industry are not provided for by traditional concepts and systems of education. The explicit knowledge approach in developing expert systems is presented through two experiments. The first describes a dedicated system written in GOLDEN LISP and the second a shell, using INSIGHT2, which has more general applications. Using expert systems forces on the user a new approach to parameter definition, and as an example an original method for the research of any anisotropy axes is developed which might well be useful in traditional programming. Two examples of application to a coal and a gold deposit are given.

Jan 1, 1987

By R. P. King

A class of gravity separation unit operations in ore-dressing relies for its operation on the production of a stratified bed. Heavier material gravitates downwards, and separation is achieved by splitting the ore horizontally, with the recovery of a dense stream and a lighter stream. The important ore-dressing unit operations that fall in this class are the jig, the Reichert cone and the pinched sluice. A new quantitative model based on Mayer's potential theory is developed here. This model is developed completely for the simple case of binary mono-size particulate materials, but the extension to units operating with feed material distributed over particle size and density is discussed in principle. The model can be used to predict the performance of these units and is very suitable for simulation. The model is tested successfully against experimental data obtained from a batch jig and a Reichert cone.

Jan 1, 1987

By G. D. Schena

The issue of evaluating the economic impact of large mineral projects in developing countries was studied by the use of econometric models. The evaluating system is demonstrated by its application to an example from Namibia. Three-dimensional graphics are used to illustrate the procedures leading to an assessment of the economic effects of the mineral development. The analysis allows the assessment of the overall economic consequences of mineral developments where there is a need to incorporate in the evaluation issues that are broader in scope than the pure financial objectives. Sets of technical coefficients are exploited for the development of input-output models of the productive structure of an economy. The models are refined to incorporate country-specific behaviours. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy wide effects associated with a new project in the mineral sector of a developing country. Synthetic measures of profitability at market and shadow prices are introduced, and the cost/benefit ratio is used to rank mineral projects according to their economic profitability. The cost is the capital mobilized for the development of the project and for increasing the productive capacity of the related satellite industries. The benefits are identified with the economy-wide increase in value added induced by the project. 80th costs and benefits are initially valued at market prices. Their ratio is likely to be an index of economic profitability superior to measures that concentrate exclusively on the benefit side of projects. To allow for market distortions, the concept of shadow prices is introduced, and accordingly project-related costs and benefits are re-evaluated. A new cost/benefit ratio at shadow prices is recalculated, which is more meaningful to the policy-maker than decision-making based on socio-economic issues.

Jan 1, 1993

By Dr. T. L. F. Muller

INTRODUCTION During the past decade a wealth of knowledge has been acquired about the mechanisms and reactions responsible for the physical properties of metals. In the field of steels, in particular, research of a fundamental nature has enabled us to interpret mechanical properties such as hardness, brittleness, creep strength, etc., in terms of atomic interactions. So rapid has been the development of physical metallurgy in some fields that publications are often outdated by the time they appear in print. The development of new steel products has been rather empirical by nature in the past and only during the past few years have new products been "designed" in terms of known physico-metallurgical phenomena. However, although this is a great stride forward it should be added that the development of a commercially successful product is a far more complicated process. In addition to the physico-metallurgical background this requires consideration of factors such as low production cost, market research and probably most valuable of all, an interested end user to co-operate in the development. This paper deals rather briefly with three of the most recent developments in steels in Britain with which the author has had some association. The main purpose of this is to demonstrate how the improved properties of the new product are based upon established physico-metallurgical phenomena. Generally speaking a commercially successful product of the type described here offers similar properties to that of an existing product at lower cost or has improved properties or features such as greater ease of cold forming, at similar cost. ULTRA-FINE GRAIN STRUCTURAL STEELS The development of higher yield strength structural steels dates back over a considerable number of years and has led to a variety of types. The one described below contains niobium as a grain refiner in an otherwise conventional mild steel matrix. By controlled rolling in a strip mill considerably increased yield strengths are obtained. In Fig. 1 are shown somewhat diagrammatically the relative hardening effects of carbon and manganese on ferrite. It will be seen that strength is enhanced by the solid solution hardening effect of manganese and the pearlite content. An obvious limitation of high pearlite content is a lack of cold workability and weldability. Manganese has to be restricted to low levels for the same reasons. The two other mechanisms which are known to impart higher strength are precipitation hardening and grain refinement. Precipitation hardening is impractical in most cases for structural steels and it is therefore clear that only grain refinement remains as a potentially useful strengthening mechanism.