Search Documents

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By D. Weijie, S. Kai, Y. Hu, X. Ning, M. Shiyi, W. Junpeng, Z. Guihong, L. Xianjie

Flotation is one of the most important processes in the copper production industry. The copper grade in the concentrate is a pivotal indicator of the flotation process performance. However, it is difficult to achieve real-time measurement through hardware sensors. Based on the production data provided by an industrial operation, a novel soft sensor based on multi-layer perceptron (MLP) is proposed for effective monitoring of this pivotal indicator. The proposed soft sensor uses the nonnegative garrote (NNG) to perform global variable selection for MLP, while a local search (LS) approach is incorporated to improve the model presented by NNG. Simulation results show that the proposed algorithm has higher prediction accuracy and better model simplicity than other algorithms. Furthermore, the variables selected are consistent with the field experience, and the developed model can provide reference of feedback control for the optimisation of the process. Keywords: Flotation process of copper ore, nonnegative garrote, local search, soft sensor, multi-layer perceptron

Jan 1, 2020

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

By Xiaoxu Sun, Jianchao Yao, Qiheng Zhu, Dubo Wang, Jiancheng He, Shijie Lu

Tower mill is considered to have a better regrinding and fine grinding effect compared with ball mill, and its application is much broader. The spiral agitator of the tower mill is driven by the motor. Media inside the mill is under the combined actions of the spiral mechanism, the cylinder, and media nearby, and these parameters are key factors affecting the grinding effect. However, it is not possible to obtain detailed information of kinematic law of media based only on traditional laboratory experiments, let alone the relationship between parameters of kinematic law of media and grinding effect. Experimentation is the only way to develop industrial equipment. However, this is time-consuming and costly, which hampers the further research of the tower mill’s grinding mechanism. The paper selects two structural parameters (gap between the edge of the spiral agitator and the cylinder wall, ratio between the diameter of cylinder and that of the spiral shaft.) and three operating parameters (diameter of media, filling ratio, the speed at the edge of the spiral agitator) as variables to do an orthogonal designed experiment of five factors, four levels, and thereby obtaining change law of grinding indicators of different parameters. Experimental equipment may be simplified to enable an applicable simulation strategy. Simulation based on a discrete element method is conducted to obtain the change law of the speed of media, collision frequency, normal force, and radial force. The relational curve between parameters of kinematic law of media and energy consumption of grinding is clarified, and key factors affecting grinding efficiency are determined. Those factors will be used for optimising the design and operating process. The research result of this paper obtained from laboratory experiments and computer simulation provides data support and theoretical bases, and has directive meaning and applicable value for tower mill’s optimisation and large-sized design. Keywords: Tower mill, discrete element method, kinematic law of media, energy consumption of grinding

Jan 1, 2020

By A. J. H. Newell, K. Doherty

A copper-gold project has required a number of trade-off studies underpinned by test work to settle on pragmatic flowsheets and throughputs to support a pre-feasibility study that provides a compelling financial case. The primary trade-off studies were based on the mine schedule, ore type feed-grade recovery relationships, likely concentrate grades and typical marketing terms as well as the estimated capital and operating costs for a range of throughputs and mining strategies. Secondary trade-off studies were conducted for specific circuits and additional processing options. Although the details of these studies are not presented, the technical options and subsequent flowsheets are discussed. While the flowsheets will be optimised during the feasibility study stage, the basis is now fixed for the four ore types that would be mined from the copper-gold orebody. The ore types, resulting from a strong weathering profile, exhibit a wide range of copper mineralisation and gold associations, as well as gangue types. They display a range of characteristics that necessitated a nuanced approach to flowsheet development. The primary separation techniques that have been employed include gravity, classification, flotation and leaching while a range of comminution methods have been selected to suit the properties of the ore types. While technical issues are important factors in terms of maximising the quality of separations, recoveries and revenues, attention to material handling, equipment characteristics, the mine schedule, and capital and operating costs are equally important considerations for settling upon a suitable and robust flowsheet. Keywords: Flowsheet, testwork, studies, saprolite gold, native copper, chalcocite, chalcopyrite

Jan 1, 2020

By F. W. Petersen

The Conference Minerals & Materials '96 was held in Somerset West, South Africa, from 31st July to 2nd August, 1996. It was organized by the Universities of Stellenbosch and Cape Town, the Cape Technikon, and the Western Cape Branch of The South African institute of Mining and Metallurgy (SAIMM). The three-day Conference was attended by 180 delegates, representing countries such as Australia, South Africa, United Kingdom, Finland, Sweden, Germany, Poland, Zambia, and Zimbabwe. The programme and associated exhibition were well organized, and each of the delegates received two volumes of proceedings containing the 77 papers presented at the Conference.

Jan 1, 1996

By M. Kumral, S. Li, M. Balci, Z. Shao

Main haulage roads play an important role in the performance of underground mines because of the cost of transportation of the extracted ore, equipment, and workers. During mine development, these roads are designed through manual tools or CAD-based software. However, the optimisation of these roads is still a complex problem due to some constraints such as minimum turning radius and maximum gradient. By utilising Dubins path theory, three elevation cases; namely low, medium and high are defined, considering gradient constraint as well as the minimum turning radius in a three-dimensional space. The shortest path between two points can then be found by the three-dimensional Dubins path algorithm with elevation constraint. As a further step, a three-dimensional Dubins path algorithm with elevation constraint for multiple points is also developed for multi-point cases. The effectiveness of these algorithms is tested through case studies in order to determine the optimal path between different points.

Sep 1, 2021

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By K. Barani, F. Moradpouri, M. Godarzi

A sampling campaign carried out on the lead flotation circuit at Lakan lead-zinc processing plant demonstrated that the Pb recovery was only about 68-69%. Characterization of the Pb flotation tailing showed that 61.4% of the Pb is in the –37 μm size fraction, which is difficult to recover by flotation. Batch flotation experiments were carried out on a plant sample of the lead flotation feed and high-intensity conditioning (HIC) was used to improve flotation recovery. The results showed that increasing the collector conditioning time from 1 to 3 minutes significantly increases the Pb recovery from 42.5% to 57.3%. Further increases in conditioning time to 5 to 7 minutes decreased the Pb recovery. With a collector conditioning time of more than 3 minutes, due to the surface cleaning effect, increasing collector and frother dosage improved the flotation selectivity and recovery, even at higher collector dosages. The Pb recovery increased from 69.1% to 79.8% with increasing impeller speed from 600 to 1250 r/min. HIC increases the flotation kinetics and greatly improves the flotation recovery and concentrate grade.

Apr 2, 2022

By B. T. McKenna, H. Nirschl, P. Morsch, B. Fränkle

Generally, filter media used in filter presses have a limited operational life. Besides mechanical damage, there is a growing deposition of fine particles with increasing filtration cycles, the so-called blinding, inside the filter cloth. The resulting decreasing pore diameters not only affect the efficiency of the filtration process itself by increasing the filter medium resistance, but also make it more difficult to regenerate the filter press between the individual cycles, e.g. leading to an insufficient cake discharge. Since tailings filtration requires handling of large process flows containing a significant fraction of particles in the lower micrometer range, an investigation into media rejuvenation is of interest. Keywords: Tailings filtration, filter fabric resistance, filter media regeneration, filter cleaning, intraweave contamination

Jan 1, 2020

By E. Öğretici, S. Kahraman

The indirect estimation of intact rock properties is particularly useful for preliminary investigations in engineering projects. In this paper we examine the usability of electrical resistivity, a nondestructive measurement, for the prediction of physical and mechanical rock characteristics. Physico-mechanical tests (uniaxial compression, Brazilian tensile, density, and porosity tests) and electrical resistivity measurements were performed on specimens of 36 rock types. Before the resistivity tests, the specimens were completely saturated with saline solution. Evaluation of the test results showed that there are medium or strong correlations between resistivity and rock properties. There are also strong or stronger correlations between the two parameters for the rock classes. The regression equations developed were statistically tested, and their validity was confirmed. The results were also compared with previous studies. The conclusion is that electrical resistivity measurement can be used for reliably estimating physical and mechanical rock characteristics.

Aug 8, 2024

By M. Stachowiak, M. Nowicki, K. Walas, A. Skoczylas, P. Stefaniak

In this paper the authors present a walking robot dedicated to the inspection of a belt conveyor’s transportation system in an underground mine. The developed robot can independently diagnose all of the key rotating elements of the belt conveyor (pulleys, bearings, drums, gears, engines) based on vibration and acoustic signals as well as typical RGB (red, green, blue) and thermal images. The article presents key diagnostic procedures applied to real industrial data obtained during robot testing.The work was developed as part of the ‘THING–subTerranean Haptic INvestiGator’ project. The authors presented the main assumptions of the research methodology developed for the needs of technical diagnostics of conveyor elements typical of inspection work performed by mining staff. Based on industrial data, the use of algorithms for elements such as rollers, drive stations, and the conveyor belt were shown. The main assumption of the research is to develop a robot adapted to the conditions of a deep mine, capable of carrying out an autonomous inspection of mining infrastructure. The conducted tests and the developed fault detection algorithms were aimed at preparing the robot for underground tests in the operating conditions of the mine.

Sep 1, 2021

By X. Chen, G. Wang, D. Wan

Computational fluid dynamics have been applied for detailed modelling of particle-bubble collisions. The most accurate approach in the previous work is using the point particle method to treat particles and bubbles. Nevertheless, the sizes of particles and bubbles are generally bigger than the Kolmogorov scale in the high turbulence of the flotation environment, which makes the point particle method inappropriate. This paper describes particle-resolved direct numerical simulation on the collisions between particles (denoted as heavy particles) and bubbles (denoted as light particles) in a homogeneous isotropic turbulent flow field, and a comparison with the point particle method.. A largescale stochastic forcing scheme was implemented within the mesoscopic multiple-relaxation-time LBM approach to maintain turbulence intensity at targetted levels. Both kinematic and dynamic collision kernels were evaluated to study the correlation of total collision events and turbulent kinetic energy (TKE) dissipation rate. The results show that collisions between particles increase with the TKE dissipation rate as radial relative velocities between particles increase with it. In the particle-resolved simulations, the dynamic collision kernels were found to not match with the kinematic collision kernels as in the point particle method. Quantitatively, they were approximately 4 to 10 times smaller than the corresponding dynamic collision kernels. Therefore, it is not reasonable to estimate the kinematic collision kernel in particle-resolved simulations as its rationales are not valid. However, the collision behaviour can still be accounted for by means of the dynamic collision kernel since it is obtained from the direct statistical analysis of the collision events. Keywords: Lattice Boltzmann Method; particle-resolved simulation; multiphase flow; collisions

Jan 1, 2020

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

By Z. Zhang, J. Niu, H. Wang, Y. Xu, J. Shi

Tribo-electrostatic separation is a promising method for effectively utiliing low-grade magnesite resources by removing quartz and improving the grade of magnesite. To determine the chargeto- mass ratios of pure magnesite and quartz, a triboelectric measurement system was employed, and a laboratory tribo-electrostatic separation system was used to separate low-grade magnesite. The results showed that the maximum difference in charge-to-mass ratio between pure magnesite and quartz particles was observed after friction with polyvinyl chloride. The grade and recovery of magnesite increased with temperature and initially increased with increasing voltage, feed rate, and air flowrate before gradually decreasing. The optimal conditions resulted in a concentrate with 46.91% MgO content and 77.36% recovery, while the quartz content decreased from 7.02% to 1.95%. These experimental results demonstrate the effectiveness and potential of tribo-electrostatic separation in removing quartz and upgrading magnesite.

Apr 14, 2024

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

Council and Standing Committees - 1983/84 President: Prof. R.P. King Vice Presidents: J.D. Austin and H.E. James Honorary Treasurer: Prof. D.G. Krige Immediate Past President: Prof A.N. Brown Members of Council: B.C. Alberts, Prof. S. Budavari, N.J. Devine, Dr C.J. Fauconnier, P.T. Fewell, C. E. Fivaz, J. S. Freer, Prof. G.G. Garrett, J.J. Geldenhuys, Dr A.K. Haines, Dr B.K. Loveday, G. Pienaar, B.E. Protheroe, Dr O.K.H. Steffen, G.C. Thompson, Dr H. Wagner, Dr P.T. Wedepohl Chairman, Witbank/Middelburg Branch: H.C. van Zyl Chairman, Orange Free State/Klerksdorp Branch: D.A. Parfitt Past Presidents Serving on Council: Dr M.G. Atmore, Dr J.P. Hugo, Dr P.R. Jochens, Prof. R.P. Plewman, G.Y. Nisbet, Dr R.E. Robinson, Prof. M.D.G. Salamon, P.W.J. van Rensburg, D.A. Viljoen, P.A. von Wielligh Standing Committee Chairmen: Adjudication, Prof. A.N. Brown; Awards, Prof. A.N. Brown; Banquets, J.S. Freer; Constitution, Rules and Policy, Prof. A.N. Brown; Excur¬sions, J.S. Freer; Journal, H.E. James; Membership, H.E. James; Phoenix National Committee, Dr M.G. Atmore; SAIMM School - Extractive Metallurgy, Dr A. K. Haines; SAIMM School - Mining, Dr H. Wagner; Special Publica¬tions, J.D. Austin; Technical Programme - Extractive Metallurgy, Dr B.K. Loveday; Technical Programme - Mining, G. C. Thompson; Technical Programme -Physical Metallurgy, G. Pienaar; Training, Career Guidance and Education, Dr M.G. Atmore; World Mining Congress - National Committee, Prof. R.P. Plewman; Working Group Physical Metallurgy, Prof. G.G. Garrett

Jan 1, 1984

By F. Hörtkorn, Y. Narainsamy

Rather quietly, a new generation of European norms dealing with earthworks has been developed over the past few years, in particular a part of EN 16907 pertaining to extractive waste. Whereas the majority of the parts deal with routine geotechnical aspects, one part deals specifically with tailings dams. The standard is currently in draft form but if this becomes a European Standard, members of the European Union are bound to comply with the regulations. As such, the standard has the capacity to influence mining in Europe and potentially in South Africa. In this paper we review the standard and compare it to the South African standard on mine residues and the recently published Global Industry Standard on Tailings Management (GISTM). We conclude found that although the European norm makes great strides towards increasing tailings dam safety, there is room for improvement. The current South African standard has served well since its inception, but can be improved by using concepts from the European and global tailings standards.

Jun 2, 2022

By G. Akdogan, P. Mutimutema, M. Tadie

The South African gold mining industry has a legacy of abundant tailings dams, which have attracted the attention of investors because of their potential as a cheaper secondary gold resource. In this we investigate study gold recovery from a refractory calcine tailings dam. Bulk mineralogy of the tailings silicates and iron oxides to be the most abundant phases. Scanning Electron Microscopy (SEM) showed gold to exist in submicrometre and micrometre sizes, as free gold, and associated with arsenic, sulphur, and silicates e.g. quartz and talc. Gold recovery by direct cyanidation was low at 17.3%. Mechanical (ultra fine grinding P80 -16μm) and chemical (alkaline, NaOH) pre-treatment and microwave roasting and microwave-assisted cyanide leaching were investigated to increase gold recoveries. Ultrafine grinding was the most effective, producing recoveries of 66.5%. NaOH pre-leaching of ultrafine milled material increased recovery to 71.5%. Alkaline pre-leaching overall increased recoveries for non-pretreated material, making this process the most preferred because it is less costly than ultrafine grinding. Microwave roasting and microwave-assisted leaching did not achieve higher recoveries than alkaline pre-treatment or fine grinding. The investigation highlights and confirms that chemical treatment with NaOH is a powerful tool for gold extraction from refractory tailings.

Oct 1, 2022

By J. Sepulveda

"Despite the recognized influence of product fineness on line capacity and downstream process performance, few mineral concentrators today use particle size measurement of the final product in automatic control applications for particle size. ‘Near-line’ particle size instrumentation has existed for decades and is utilized in modern concentrators, but low availability and measurement frequency, due to problems with slurry sampling and transport systems, make these technologies unreliable for use in automatic control. An innovative technology for real-time particle size measurement on individual hydrocyclones, named CYCLONEtrac™ PST (particle size tracking), has been developed by CiDRA Minerals Processing, and proven in commercial installations, demonstrating near 100% availability with minimal maintenance requirements, thus overcoming the limitations of previous technologies. Potential stakeholders require convincing, reliable information regarding the economic value delivered by automatic grind control projects. In this paper we present a methodology for estimating such value with the CYCLONEtrac™ PST technology, and demonstrate unique opportunities to improve process stability and performance. Based on actual plant data accumulated over time, the evaluation approach assesses and highlights the significant potential process improvement that can be expected with the particle size tracking technology. As an extension of previous work, in this paper we present the key operating criteria for optimizing the production of valuable metals and increase mill throughput by identifying the optimal grind size. As this requires operating closer to the process boundaries, accurate real-time particle size measurements, such as those provided by the CYCLONEtrac™ PST system, become essential for achieving the maximum potential value from every operation. For further illustration, data from three different copper plants is compared.Introduction Owners and operators of mineral concentrators constantly search for the most economically attractive way to increase the output of valuable metal. A logical approach is to identify a key parameter that has the greatest impact on the performance of multiple stages of the process and then use a holistic analysis methodology to determine how this key parameter can be controlled to optimize the final output.Particle size is widely recognized as such a key parameter; however, very few concentrators today use real-time particle size measurements for automatic control of the final product size due, to a large extent, to the inherent limitations of existing technologies. ‘Near-line’ particle size measurement instrumentation, which has been used for decades, typically suffers from low availability because the fundamental measurement technologies were developed for other, less demanding industries and then adapted to the harsh environment of the typical mineral concentration process. An outline of the key differences among the available technologies used for particle size measurement in comminution circuits has been completed in previous work, and plant data has proven the benefits of measurements on individual cyclones – something that, until now, has not been possible (Cirulis, 2017)."

Nov 1, 2018