Search Documents

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By H. C. George

This bulletin deals with prime movers, power-transmitting machinery, and the surface equipment and methods used to pump oil wells. It does not discuss geological problems nor the methods and equipment used in drilling or at flowing oil wells. Much of the presentation is by photographs and drawings which are described in the text. Underground equipment and methods for pumping oil wells will be discussed in a later publication of the Bureau of Mines.

Jan 1, 1925

By Lynn Alcorn, Jeffrey Shawn Peterson

Data collected by the Mine Safety and Health Administration (MSHA) has shown that roof bolting machine (RBM) operators are the second most likely type of underground mining machine operator to be are over exposed to noise, per the MSHA Permissible Exposure Limit. In response to this, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has initiated a project to develop engineering noise controls for roof bolting machines. Key to this research is an evaluation of the duty cycle of a typical roof bolting machine operation and this paper presents the results of such an exercise for data collected at two cooperating coalmines. The evaluation entails a time motion study of an operators' shift, logging each activity for time (e.g., tramming the machine, drilling holes, installing the roof bolt, etc.) and the noise levels associated with each task with a Larson Davis Spark 705+ dosimeter. NIOSH post processed the data to determine which tasks the operator devotes the most time to and the noise dosage accumulated during those tasks. These results provide insight into which portion of the operators' duty cycle is the most prominent contributor to noise exposure and thus, where research activities for the development of engineering noise controls should be focused. It was determined that the task of drilling holes is the most significant source of the operators' noise exposure and project research has focused on engineering noise controls to reduce the noise emissions generated during the drilling portion of the machine duty cycle.

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945

This Information Circular describes the Bureau of Mines Minerals Availability System (MAS), presents the Resource Classification Manual used for information input to a computer file, and discusses the methods of collecting and assembling background material' basic to coding the data.

Jan 1, 1974

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983

By W. R. ARGYLE, R. A. SHERMAN, Henry Kreisinger, John Blizard, B. J. CROSS, A. R. Mumford

On entering the World War the United States was confronted with the necessity of building in a short time a large number of ships of tonnage adequate to transport troops and war materials to Europe and to carry food supplies to the allied countries, whose merchant fleets had suffered greatly by submarine warfare. The necessity of building ships quickly led to the formation of the United States Shipping Board, which was charged with the duty of developing an efficient organization for the purpose. Such an organization was developed under the name of the Emergency Fleet Corporation; it was under the control of the Government, but could conduct its business in the most direct way, like a private corporation. In order to build the largest- number of ships possible without drawing too heavily on the steel industry, which was already taxed heavily by the production of munitions, it was decided to build wooden as well as steel ships. These ships were built from a few standard designs to enable a large number of duplicate parts to be fabricated in inland shops and transported by railroad to the shipyards on the seacoast, where they were assembled into ships. In other words, the plan was to manufacture the ships rather than to build them. The shops on the seacoast were reserved to make those parts of the ships' equipment that could not readily be transported. The inland shops made the parts that could be transported to the seacoast by railroad. Among the more important parts of the ships' equipment to be standardized were the boilers. As the Scotch marine boiler in large units is bulky and can not be transported by railroad, and as, for the same capacity,much more steelis needed in its construction than for water-tube boilers, a few simple designs of water-tube boilers were developed that inland shops having ordinary equipment could make in large quantities.

Jan 1, 1924

By Thomas M. Nasiatka

This report briefly describes the present state of the art and the technological highlights of tunneling from its inception to the present. The discussion is concerned primarily with tunnels driven through relatively competent rock for mine development and various civil purposes. In addition to pinpointing the major technological breakthroughs in tunneling, this report indicates their general effect on the speed of tunneling. The tunneling speeds are based upon data from approximately 80 tunnels listed in the appendix. These data include length; cross section shape and dimension; type of rock; tunneling method; method of breaking, loading, and transporting the rock; average linear progress rate; and cost in values during the period of construction. Most of the tunnels described have diameters of 15 to 30 feet.

Jan 1, 1968

By Jos. R. Guiteras

This paper describes the operations of the St. Joe Mining & Milling Co. in Boulder County, Colo., as of June 1936. Later a brief visit was made to the mine in September 1936; information obtained at that time has also been recorded. The company operates a gold mine, the Grand Republic, in the Sugar Loaf mining district; a 100-ton flotation mill in Lefthand Canyon near Gold Hill; and a custom sampling punt, the Boulder Ore Sampling Works, at Boulder, Colo.

Jan 1, 1937

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting & Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. "V. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K Thomson, W. G. Derby, and the assistants of the writer, K. 1V.McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the aid of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate anyone method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By John D. Spencer

Air and water pollution and land reclamation relating to coal mining and utilization continued to be featured in research and technologic work on coal by the Bureau of Mines in 1967. Details of the environmental studies are given in this report, along with accounts of other research relating to the mining and utilization of coal. Other studies that were continued during 1967 included health and safety, mine explosives, coal preparation and transportation, coal utilization processes, chemistry and properties of coal, inspection and analysis, and inter-national activities. Publications issued in 1967 are cited throughout the report and in appendix C. Bureau of Mines research centers and laboratories are listed in appendix A, and organizations contributing to or cooperating in the work, in appendix B.

Jan 1, 1968

By Chas. F. Jackson

This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the United States Bureau of Mines and made possible through the cooperation f many mining companies in the United States and foreign countries. The preparation of this paper follows a field study of top-slice mining during which the author visited and discussed with operating officials a large number of iron mines in the Lake Superior region. During this study special note was made of changes in top-slicing practice during the past decade, prior to which the author had acquired several years experience with the method through active connection with a number of mines employing top slicing.

Jan 1, 1931

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007