Search Documents

By H. E. Peterson

This report revises an earlier publication by the Bureau of Mines on tungsten analytical procedures and expands the coverage by including appropriate procedures for the critical impurity elements that commonly occur in tungsten ores and concentrates (13).3 The basic methods described are not original, but many of the modifications to improve reliability and sensitivity were developed by the Bureau. Gravimetric and colorimetric methods currently used for the determination of tungsten in ores, mill tailings, and concentrates are described. Colorimetric procedures are preferred for low concentrations of tungsten, whereas either procedure is satisfactory for moderate concentrations. Conversely, a gravimetric method is preferred for the determination of tungsten in concentrates.

Jan 1, 1963

Illinois has the largest reported bituminous coal resources of any state and is one of largest coal-producing states in the nation. Coal-bearing rocks underlie about 65 percent of Illinois, including all or part of 86 of its 102 counties. An estimated 18 1 billion tons of coal resources are still in the ground. Using present mining methods, more than 30 billion tons of coal are classified as recoverable. This represents almost one-eighth of the total recoverable reserves of all types of coal in the United States. The state's surface mining regulatory program was conditionally approved June 1,1982. It received full approval October 25,1988. The Abandoned Mine Land Program was approved June 1, 1982, and the AML emergency authority June 11, 1984.

Jan 1, 1992

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By William P. Diamond

Ventilation has long been the primary means of controlling methane emissions in underground coal mines. However, as mining has progressed into gassier areas of U.S. coal basins, supplemental means of methane control have become of interest, if not a necessity, for continued safe and productive mining operations. This paper describes the history and technology of methane drainage in the United States and other countries. The methane drainage technology developed in European countries is a valuable resource since their longer history of mining has already forced mine operators to deal with methane emission problems only now being experienced in the United States. Methods for assessing the need for methane drainage and the data required for planning and implementing an appropriate system are reviewed. The effectiveness of the various technologies for reducing methane emissions underground and/or the in-place gas content of individual coalbeds is illustrated with case studies. In addition to the safety and productivity gains to be realized from methane drainage systems, the potential for commercialization of coalbed methane is discussed.

Jan 1, 1994

By Joan C. Biordi

In this research by the Bureau of Mines, slightly lean CH4-O2-Ar flames at 0.042 atm with and without small amounts of the inhibitor CF3Br were probed using molecular beam and mass spectrometric techniques. Ratios of product concentrations to reactant concentrations were formed and compared with the equilibrium constant for seven reactions--(l) H+O2 = OH+O, (2) O+H2 = OH+H, (3) OH+H2 = H2O+H, (4) OH+OH = H2O+O, (5) CO+OH = CO2+H, (6) Br+HBr = Br2+H, and (7) H+HBr =H2+Br--to determine to what extent they may be considered balanced in various regions of the flame. With the possible exception of reaction 4, none of the reactions are completely balanced until maximum flame temperature is reached. Once the reactions become equilibrated, their balance is maintained as the temperature and radical concentrations falloff in the secondary reaction zone. Reaction 7, in inhibited flames, is balanced at relatively low temperatures, comparable to reaction 4. Reaction 6 was found not to balance in either the secondary or primary reaction zones. Radical decay in the secondary reaction zone was analyzed using the pool-decay concept. The important recombination reactions were judged to be H+OH+M~H2O+M, and H+O2+M?HO2+M. A rate coefficient of 2x1016 cm6 mole-2 sec-1 is calculated for M = the burnt gas mixture of Ar, HaO, CO2, and 5x1015 cm6 mole-a sec-1 is calculated for M = Ar (both for T = 1,750±150 K).

Jan 1, 1977

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993

By W. R. Reed

Drilling with water has the potential to significantly reduce the respirable dust concentrations generated from small-diameter rotary drills when drilling blastholes on surface mining operations. However, water adverseky affects tri- cone drill bits commonly used in surface drilling operations, causing excessive wear and premature replacement. Consequently, dry drilling with a dust collector system has the most widespread use in the industry. Tests have been conducted by the National Institute of Occupational Safety and Health (NOSH), Pittsburgh Research Laboratory (PRL) on a newly designed device for smaller diameter drills that separates the water from the bailing air before it reaches the bit and thus provides the cost benefit of dry drilling while providing the benefit of wet drilling for dust suppression. The water that is delivered to the hole with the bailing air is separated from the air by a proprietary mechanical device that is encased in a drill sub (short section of drill rod/pipe) located immediately behind the cutting bit. A cascade cyclone and a real-time dust monitor were used to sample dust emissions from the holes. Dust concentrations and silica content were measured when drilling dry versus drilling wet. The tests show that drilling with this water separating sub can reduce both measured dust emissions from the boreholes and visible dust around the drill rig.

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

By Stuart Lipoff, John E. Trombly, Paul Brien, O&apos

System objectives and design criteria for an in-mine ULF radio paging system are discussed. Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

By Frank G. Schwartz

The Bureau of Mines developed a rapid test method for predicting the stability of motor gasoline during long-term storage. The amounts of gum and inorganic residue formed in 13 gasolines during a l6-hour oven test at 200° F were compared with the amounts formed in the same gasolines stored at 110° F, and analyzed following 8-, 16-, 32-, 44-, and 52-week storage periods. Satisfactory methods were developed for predicting gum and inorganic residue formation during fuel storage periods as long as 32 weeks at 110° F, the approximate equivalent of 5.7 years at 80° F. The only data required to apply the methods are the amount of gum and inorganic residue formed, and the amount of oxygen that reacted, during a l6-hour oven test. A direct relationship existed between inorganic residue formed during the oven test and during 110° F storage. Statistical treatment of the data showed predicted values were as reliable as determined values. By use of a modified Arrhenius equation, the 110° F storage time can be extrapolated to equivalent time at any temperature below 110° F. Thus by combining the stability prediction method with the mathematical extrapolation, the storage performance of motor gasoline for extended periods can be estimated at any temperature up to 110° F.

Jan 1, 1968

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

By Larry A. Haas

The U.S. Bureau of Mines investigated the use of organic binders as substitutes for bentonite in agglomerating iron ore concentrate. Over 30 organic binders were evaluated at several dosage levels in laboratory tests. The binder groups producing the greatest green pellet strengths were natural gums (guars carboxyl methyl celluloses) and gelled starches. The nongelled and alkalized starches, starch acrylic copolymers) wood-related products, and dairy products were less effective but better than bentonite. The highest wet pellet drop numbers were obtained with binders that had a medium plate water absorption value (>500 and <10)000) in distilled water and a high slurry viscosity (>75 cP) at 6 pet solids. The highest dry compressive strengths were obtained with binders that gave the highest adhesive tensile strength (>4 kg/ cm2) on iron oxide lap-joint substrates. Pellets with 0.1 pct organic binder had lower compressive strengths and reduction disintegration indices than those with 1 pct bentonite, but higher reduction rates. Pellets with carboxyl methyl cellulose and gelled starch had higher softening temperatures than those with bentonite. Overall, the most promising binder is gelled starch. Its price makes it more cost effective than carboxyl methyl cellulose, and its pellets have metallurgical properties superior to those of bentonite pellets.

Jan 1, 1989

By W. E. Miller, W. P. Yant, G. W. Jones, R. E. Kennedy

"The determinations of the limits of inflamability of diethyl ether and ethylene in air described in this report were made primarily for comparison with similar determination of other compounds in the same apparatus and by the same laboratory technic. The experimental procedure and the results obtained differ somewhat from those of other investigations. The work also included determinations of the limits of inflamability of these combustibles in oxygen The investigation,was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines in cooperation with Merck & Co., Inc. LIMITS OF IMFLAMIABILITY OF DIETHYL ETHER-AIR MIXTURESThe limits of inflamability if diethyl ether in air were determined for upward propagation of flame in an upright, closed 8-liter, cylindrical iron bomb 10.2 cm in inside diameter and 96.5 cm in length. This bomb been described in a previous publication. 6Two brands of diethyl ether were used, one a C. P. sulphuric ether manufactured by Baker & Adamson, and,the other Merck & Co. product manufactured for anaesthesia and containing about 3.5 percent of ether alcohol."

Jul 1, 1935