Search Documents

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By William C. Larson

This Bureau of Mines report discusses uranium in situ leach mining in the United States to acquaint the public with an overview of this emerging mining technology. This report is not intended to be a technical discussion of the subject matter, but rather should be used as a reference source for information on in situ leaching. A list of in situ leaching publications is included as well as engineering data tables for almost all of the active pilot-scale and commercial uranium in situ leaching operators. These tables represent a first attempt at consolidating operational data in one source, on a regional basis. Additional information is given that discusses the current Bureau of Mines uranium in situ leaching research program. Also included is a listing of various State and Federal permitting agencies, and a summary of the current uranium in situ leaching operators. Finally, a glossary of terms has been added, listing some of the more common terms used in uranium in situ leach mining.

Jan 1, 1978

By A. L. Engel

This publication describes further research by the Federal Bureau of Mines in beneficiating domestic manganese ores. The ores selected for treatment were typical of many manganese deposits in California and Nevada in that they have not been economical to mine because they are low grade or contaminated with siliceous minerals and are not amenable to physical concentration.3 4/ It would be desirable to develop a simple treatment method resulting in nearly complete extraction of manganese from these ores and applicable to small-scale operations. Sulfation reduction appeared to be such a method. The studies reported in this publication were directed toward sawdust or lignin-sulfonates as reducing agents. Sawdust, as waste from lumbering, and lignin-sulfonates, byproducts of woodpulp papermaking, are comparatively cheap and may be available in areas where manganese ores are found. Sugar, oils, and coal were also tried as reducing agents.

Jan 1, 1960

By R. W. Stahl

Increasing use of continuous miners, especially the boring type, has focused attention on the inadequacy of face ventilation in coal mines. The bulk of the machine, the rapid advance of working faces, and the increased liberation of methane from the larger expanse of freshly exposed coal surfaces have created ventilation problems that were unknown with conventional mining equipment. Ignition of gas, especially that caused by machine bits striking hard rock or pyritic inclusions, have increased at an alarming rate. As the mines penetrate beds under thicker cover at an ever-increasing rate of face advance, this problem will probably increase unless face ventilation is improved. A previous survey, described in Bureau of Mines Report of Investigations 5414, Auxiliary Ventilation of Continuous Miner Places, disclosed that auxiliary fans with tubing generally improved circulation of air and removal of gas at the face. The study here reported attempts to examine, face ventilation at various mines and to note any plan or innovation of. air coursing that industry might adopt to reduce the danger of gas ignition. ACKNOWLEDGMENT The mines visited were very cooperative in the study-and-generously supplied any data requested.

Jan 1, 1960

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By Donald R. Corson

The Bureau of Mines is conducting research on the effects of various established and potential soil-stabilization additives to hydraulic backfill. This initial phase is an evaluation of the effect of inclusion of varying amounts of Portland cement and combinations of cement and a dispersant on the bearing strength of backfill. Results of unconfined compression tests are given for over 200 sample cylinders incorporating a fill material with cement or cement and dispersant. Inclusion of a minor amount of dispersant (0.2 percent by weight) is found to yield a significant increase in strength for 20-to-1 and leaner sand-cement mixes. An apparent optimum concentration of dispersant exists beyond which no further increase in strength is achieved. A dispersant-cement ratio of l.8- to-1 yielded a strength increase of 515 percent over the strength of untreated 40-to-l sand-cement mixes.

Jan 1, 1966

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Roger L. King

The Bureau of Mines has developed probes to be used in emergency mine rescue operations by being lowered through a borehole drilled into an underground mine. Various probes can provide two-way voice communication with trapped miners, continuous mine atmosphere monitoring, temperature indication, and television searching capability. At present, an infrared imaging probe is being developed for "seeing" through coal smoke.

Jan 1, 1976

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959

By E. H. Denny

"IntroductionOn May 27, 1927, a coal-dust explosion occurred at the Palagua No. 5 mine of the Victor American Fuel Company, Delagua, Colorado, resulting in the loss of even lives and in and in considerable damage to the main slope and to several overcasts the explosion did not extend into the mine working where 125 additional men were employed but escaped uninjured. It is believed that the saving of these 125 men and the evidence of large property loss were due in a large measure to coal-dusting and of other sanity measures taken by the coal company management. A number of features connected with the explosion and mine safety practice seem worth the attention of the mining public and grateful acknowledgment is made to the Victor American Fuel Company for its aid in assembling the data herein contained."

Nov 1, 1927

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980

By Leonard Obert

A triaxial procedure is described for measuring the modulus of elasticity and Possion's ratio of stress relief cores , that is , the concentric hole cores obtained by the overcoring technique . The elastic constant determinations can be made at stress levels comparable with those encountered in underground mining . The results from tests on an aluminum alloy calibration specimen and four rock specimens are included .

Jan 1, 1964

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By Howard C. Turnage, Dana T. Updyke, Wayne C. Muhler

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leaky feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 6, 1980