Search Documents

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By John R. Bartels

This report discusses an improved method for rerailing underground railcars devised in a joint effort by the Bureau of Mines and Hoesch MFD. This improved method utilizes a lightweight hydraulic ram with hand-pump activation to move a bridge-mounted roller carriage in conjunction with steel-reinforced air-lift bags. This method provides a lightweight portable system in which only two workers are required to perform the mine car rerailing operation. Because of the very narrow confines in underground mines, use of overhead cranes and other surface rail techniques is not possible. This new system is designed for very low profile work, and provides the necessary lifting force from light- weight compressed-air bottles.

Jan 1, 1985

By C. E. Munroe

In order to meet the emergencies of the world wr, tne quantities of explosivea produced in the Unitecl States, and the number of explosives plants were onti:.1.1.:l,lly ncreased so that when the armistice was declared the Government had on hand larg ..mounts oi militazy explosives in excess of existing military needs. Tle stor3.gs of these explosives entailed a liirge expense and their protection neessitatei the employment of m'3.l'lY men who could be better employed otherwise in the military estlish.11ent. Moreover, mar.y ex.ploives, like QJ.l other material, deteriorate on prolonged storage, They lose tht precise definiteness of properties and behavior on which reliance· is placed in military operations, The continued expen3e and d3.nger ttending storage of theae explosives might be diminished by dcst1et1on of the surplus beyond immediate needs, but such·deetniction is danger• ou5 qnd coetly. Hence, the evident solution o! the problem was the salvage d prompt ut111zation of the ru.rplua •

Aug 1, 1922

By Wilber Duvall, Leonard Obert

"INTRODUCTION This report is the first of four to be presented on the microseismic method 4/ of predicting rock failure in underground mining. The application of the microseismic method to one specific case, namely, that of predicting rock bursts in deep mining, has been described in two previous reports. 5/ 6/ Since the publication of these reports 5/ 6/ the method has been extended to other fields of mining, end it is the purpose of this report (Part I) to describe the general microseismic method, giving the empirical facts upon it is based, the different testing procedures, the method of recording and analzing the data, and the interpretations that can be obtained there-from. Part II will describe a series of laboratory experiments that were performed to give information on the origin of microceismims and the microseismic properties of various rocks. Part III will cover application of the method to specific mining problems together with a brief description of a number of investigations performed during, the last three years. Part IV will describe in detail the microseicmic equipment used in the various phases of these investigations."

Feb 1, 1945

By Harold M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since In most fields gas under pressure is the main source of the energy causing the oil to move throug the sands into the wells and thence to the surface, this coincident production of natural gas will contime as long as present day producing methods are used. Generally the use of this gas is restricted, and markets are not readily available Consequently, a large portion of the gas produced at such times is often wasted by being blown into the air.

Dec 1, 1930

By W. H. Young

PRODUCTION of bituminous coal and lignite increased substantially in 1963 compared with 1962 figures. The major items of production, consumption, exports, and productivity increased. However, certain key items declined. For the fourth year there was no upward trend in mechanization; the percentage of total tonnage mechanically loaded remained the same as in the 3 previous years and the percentage of total tonnage mechanically cleaned was smaller than in the previous year. Furthermore, the percentage of total production mined by stripping and by augers increased. Most significant was the continued decline in average value and employment. Production.-The output of bituminous coal and lignite in the United States in 1963--459 million tons-was 9 percent greater than the 422 million tons produced in 1962. Production was greater in 1963, largely because of expanded consumption by the electric utilities and an increase in exports.

Jan 1, 1964

By William L. Crentz

Floyd County, KY., contains sizable deposits of high volatile bituminous coal. Some of the coals have been blended with higher-rank coals and used in the manufacture of high-quality metallurgical coke. The Upper Elkhorn No. 3, Upper Elkhorn No. 2, and Upper Elkhorn No. 1 beds produce the bulk of the present output in the county and contain the main known reserves of coal. Little information is available concerning the quality and extent of the deposits underlying the Upper Elkhorn No. 1 bed, although small operations in the past have worked a bed that is reported to be; the Lower Elkhorn. Undoubtedly, these lower beds occur in Floyd County, but depth Will preclude their development into a major source of fuel as long as large deposits of more-accessible coal are available. More is known of the occurrence of the beds above the Upper Elkhorn No. 3 owing to sporadic mining ventures in the upper measures. Many of the coal samples from beds above the Upper Elkhown No. 3. were collected in mines that had been abandoned. Almost all of the present production of Floyd County coal is taken from the Upper Elkhorn beds, and it is unlikely that their dominant position as coal producers will be challenged in the near future. Table 1 shows the coal production of the county by beds, during 1950.

Jan 1, 1952

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By Robert W. Geehan

"INTRODUCTION The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Many of the mines were developed.A preliminary examination of the Sultan mine was made in January 1945 by the author, who recommended investigation by drifting and crosscutting. The Bureau conducted a project at the mine from April to June 1946. Claims investigated are in sec. 20, T. 25 S., R. 58E., Mount Diablo base and meridian, in southern Clark County, Nev., about 7 miles southwest of Good-springs.The Sultan mine has been an intermittent producer of zinc-lead-silver ore since 1910. During World War II, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting& Refining Co.'s smelter near Salt Lake City, Utah. Throughout the past year, ore has been milled and the concentrates have been shipped to the smelter."

Sep 1, 1947

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By W. H. Kerns

The Simon & Coles manganese deposit in Sherman Valley, Bedford County, Pa., was investigated by the Bureau of Mines during the fall of 1942. Two churn-drill holes; 65 and 75 feet deep were bored, and 8 channel samples were taken. Manganese occurs at this property in the form of psilomelane and manganiferous iron as replacement of the red sandy shale of the Much Chunk-formation. Two cars of manganese ore had been shipped by the owners in 1940, of which one averaged 10.9 percent manganese and the other 21.3 percent manganese. One car of hand-sorted manganese ore that averaged-45 percent manganese was shipped in 1942.

Jan 1, 1948

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By S. M. Runke

[The coarse-grained granitic pegmatities of the United States have long been a source of many important industrial minerals, because of this, they have been studied intensively by geologists, mining engineers, end metallurgists. These studies have amassed a rather astounding array of published and unpublished information. Correlation of geological studies between individual pegmatites, as well as between major districts, has brought fort come semblance of order to the knowledge of the structure and mineralogical composition of those highly complex and irregular deposits, making it possible to classify certain pegmatites and pegmatitic zones into several grouts of associated minerals, based upon the presence or absence of the minor minerals of beryllium and lithium. This classification or trouping of minerals, with the methods that have been developed for recovering certain of these minerals, possible a systematic approach to the winning of many of the industrially important minerals from pegmatite rock by u single integrated process.]

Jan 1, 1952

By L. W. Kelly

The purpose of this paper is to indicate some of the benefits that have been derived in the Zeigler No. 3 mine by using roof bolts under extremely adverse roof conditions J with the thought that much better results could be obtained in other mines with more normal roof conditions by applying some of the practices that were developed in this mine. Some of the benefits that have been obtained in this mine, which will be shown in this paper, are: 1. Increased tonnage per man-shift at the face when roof bolts are used, as compared to the tonnage under similar conditions when conventional timbering methods were used. 2. Increased efficiency of roof bolting by giving the foremen a definite plan to follow. 3. Reduction in delays caused by failures of the trailing cables of loading, mining, and drilling machines. 4. Reduction in the number of accidents after roof bolting was adopted. Inasmuch as the success that followed roof bolting in this mine was obtained under one of the most treacherous roofs in the Middle West, it is reasonable to suppose that correspondingly better results could be obtained under more favorable roof conditions by using the same procedure.

Jan 1, 1952

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed product, (3) the differences in gradation and particle shape produce- by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the seine tyre of stone. This report deals with relationship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966