Search Documents

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By A. C. Richardson

During the past two and a half years the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive study of coal preparation in the State of Alabama. Considerable time has been devoted to the study of the washing characteristics of the Mary Lee bed and the various methods used in preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery Of the Republic Steel Corporation, Sayreton, Ala.

Jan 1, 1931

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and. investigations of subbituminous coal and lignite.4/ Appropriations were made in July 19 7, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typical subbituminous coal was selected for an extended series of tests in the standard. Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncoking coal was the first one of its rank that had been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall temperatures ranging from 500°C. to 1,110°C. in 100°C. steps. All products are collected and measured; their physical and chemical properties are then carefully determined to ascertain the gas- and coke-making properties of the coal. During the last 10 years approximately 50 representative American coals have been tested in the Bureau of Mines equipment. The results on the first 30 coals and a complete description of the test procedure are contained in a joint publication of the Bureau of Mines and the American Gas Association.7/ The remaining twenty coals have been reported in Bureau of Mines reports as Technical Papers and Bulletins.

Jan 1, 1939

By W. W. Odell

Engineers interested in the manufactured-gas industry have witnessed p pronounced improvements in gas-generating equipment and marked changes in operating procedure during the past decade. In spite of these changes, however, the trend of development in the near future seems to be doubtful. Uncertainty exists mainly because no one can yet accurately calculate the number of years which will elapse before petroleum products become too expensive for, general use in making gas. Research in this field has been active, and the ultimate results are awaited with interest. Some engineers predict that in the future coking coal will be carbonized on such a large scale that coal gas will be used (straight or modified) for city distribution; others maintain that gas oil will be used in large quantities in the production of base gas; they believe that it will be economical to use oil even at appreciably higher prices. The question involves, among other; factors, consideration of initial and relative costs of equipment, flexibility of operation, salability of coke, cost of distributing different gases, and the relative value of by-products, It is common belief that for many years large quantities of oil will be used in gas-making, particularly in the generation of peak gas or that water gas will be used for the synthetic production of hydrocarbons to enrich additional water gas. In this paper interest centers in a discussion of the practicability of employing synthetic processes in view of reported investigations of the chemistry of the synthetic reactions. For many years it has been known that the chief components of water gas would react chemically under proper conditions to form methane. As long ago as 1903 a patent3 was issued in this country for a gas-making process which included the synthetic production of methane. More recently the studies of numerous investigators here and abroad have shown that besides methane it is possible to produce other paraffins, olefins, and additional, materials adaptable for enriching water gas or for other uses. The question arises: In what manner, if at all, can such processes be incorporated, as a part of the gas-making scheme in a city-gas plant?

Jan 1, 1928

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By R. L. Benner

A compound stability diagram was constructed by the Bureau of Mines for the Zn-Fe-S-O system to show the phases that should be thermodynamically stable at various temperatures, oxygen pressures, and SO2 pressures. The diagram was demonstrated to have good qualitative value for predicting stable phases that may, in turn, be related to the recovery of zinc in the leaching phase of the electrolytic zinc process. The study showed that roasting temperature is the most Significant variable in preventing roaster formation of zinc ferrite, which is directly related to subsequent extraction of zinc in the leaching step.

Jan 1, 1966

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous selective flotation tests of barite-fluorspar ores from two deposits near Marion, Ky., to determine the technical feasibility of recovering commercial grade fluorspar and barite concentrates. The lignin sulfonate-sodium fluoride method of floating the fluorspar successfully produced acid-grade fluorspar concentrates. Flotation of the barite from the fluorspar tailing using petroleum sulfonate collector yielded concentrates suitable for use in compounding oil-well drilling mud. The fluorspar and barite recoveries were about 82 and 85 percent, respectively.

Jan 1, 1963

By Frank E. Cash

The information in this report covers the accident experience of the pebble-phosphate industry of Florida for 1935 and 1936, as well as the 5 years 1930-34, inclusive, statistics of which were published in Information Circular 69174/. The compilation and publication of such accident experience statistics enable the pebble-phosphate industry, as well as other industries, to consider relative hazards and to compare experience and thereby promote accident prevention.

Jan 1, 1937

By S. E. Khalafallo

The Bureau of Mines investigated the kinetics of reduction of wustite and magnetite with carbon monoxide. A mechanism was postulated wherein the interaction between gaseous and absorbed carbon monoxide appears to be the rate-determining process. This mechanism fully accounts for the experimental rate equation JL.h relates th velocity of reduction to the pressure of the reducing gas at constant temperature. It also explains the variability of the heat of activation of the reduction process with the state of aggregation of the oxide material. The integrated rate equation is in perfect agreement with the experimental reduction-time curves.

Jan 1, 1966

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1954 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline. Data also are given for 30 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers I 1954 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 15 producers of aviation jet fuels are represented.

Jan 1, 1955

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010