Search Documents

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is

Jan 1, 1980

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By J. A. Taylor, H. F. Yancey

"INTRODUCTION Froth flotation as applied to coal is a process for separating desirable carbonaceous material from undesirable inorganic matter. In general, the feed must be finer than one eighth inch in size. The principal use of the process in the preparation of coal appears to be in the treatment of the fine sizes produced by breakage during mining and preparation.The Bureau of Vines in Information Circular 6714 has published general information on coal flotation, summarized investigative studies of the process, and described operating plants throughout the world with their tonnage, reagent consumption and operating costs.4ACKNOWLEDGMENTSThe present study of means for depressing pyrite and reducing ash ty froth flotation was conducted at the Northwest Experiment Station of the United States Bureau of Wines in cooperation with the College of vines. University of Washington, under the general direction of A. C. Fieldner, chief engineer, Experiment Stations Division, Bureau of Wines. Grateful acknowledgment is made for suggestions and criticisms received from W. H. Coghill, supervising engineer, U.S. Bureau of Mines Mississippi Valley Experiment Station, Rolla, Mo.; J. B. Morrow, and R. E. Zimmerman, of the Pittsburgh Coal Co.; and Dean Milnor Roberts and Prof. Joseph Daniels, of the College of Mines, University of Washington.FLOTATION AND DEPRESSIONA substance will tend to float if its surface attracts a gas film more strongly than it does a liquid film when both air and liquid are competing for this attraction. On the other hand, a substance will not float if its surface attracts a liquid film more strongly than it does a gas film. All theories of depression depend upon this fact. A wetted particle of floatable size most likely will be found in the tailings after the flotation process has been completed.The crux of flotation is the selective wetting of the undesirable material that tends to float. Two general methods 5, 6, 7 of depression are in use: One combines a chemical substance with the surface to form a wettable compound, and the other employs some colloidal or ionic substance which the surface selectively adsorbs, thereby forming a wettable surface."

Jan 1, 1935

By F. D. Everett

The Burgin shaft of Bear Creek Mining Co. near Eureka, Utah, was sunk during 1956 and 1957 as part of an exploratory program, searching for lead, zinc, copper, silver, and gold ore bodies hidden from the surface by several hundred feet of volcanic rocks. This paper describes the sinking methods and operating practices of Centennial Development Co., contracting firm for Bear Creek Mining Co., in sinking a 3-compartment vertical shaft 1,100 feet. The operation featured the Cryderman positive-action, clam-type shaft mucker. The shaft was completed in 142 days by a shaft crew of 10 men and a top force of 10 men, including supervision.

Jan 1, 1959

By John F. Wiggert

The first signal system used in the Homestake mine between the cagemen and hoisting engineers was a mechanical one. It consisted of small cables or jointed steel rods hung in the cage compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' positions by means of bell cranks and steel wires. At the various stations the bell lines were also fitted with bell cranks and connected levers, so that the cagemen could operate the bells from the stations when they were handling rock or other material and not riding on the cages. Such a system was inherited from the days before extensive electrical development. It served quite well for shallow shafts, but for depths of a thousand feet or more it was very slow and cumbersome. It required consider-able muscular effort to operate it quickly, because of the inertis of its great weight and also because of frictional resistance. The maintenance cost was quite high because of the many wearing parts.

Jan 1, 1937

By Harold Bailie

The purpose of this Bureau of Mines report is to furnish information on mining practices applied to flat-bedded fluorspar deposits in southern Illinois. It presents new and improved operating procedures and specialized techniques applicable to deposits of this type. All of the operating mines of the Ozark-Mahoning Co. in this area have been opened by vertical shafts which connect with levels consisting of haul-age ways, stopes, and loading stations. The stoping practice used locally called room and pillar, is open stoping with pillars left at different distances and diameters. To facilitate haulage and drainage, the mines are worked from openings turned off the main haulage drift on a grade to conform with the dip of the ore beds. The ore is predominantly fluorspar with smaller amounts of galena and sphalerite that contain traces of cadmium and germanium. The principal gangue minerals are limestone, calcite, shale, barite, and sandstone. The rock hardness ranges from relatively soft shale to hard, abrasive sandstone.

Jan 1, 1960

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference Index with abstracts of all pertinent literature. A particular strawman system design analysis is Included for the Helvetia Coal Co. Lucerne #8 mine In the Upper Freeport seam.

Jan 1, 1979

By D. J. Parker, D. Harrington, L. H. Harrison

"INTRODUCTION The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of life and damage to property, with special application to the mining industry.The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment, through improved types of lightning arresters, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures.LIGHTNING PHENOMENAIn 1751, Franklin proved that, lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:"

Apr 1, 1948

By John C. Cook

This was a study to identify and evaluate known technologies employing electromagnetic resonance phenomena in solid minerals for their identification and assaying, particularly assay logging of exploratory boreholes. A comprehensive literature search and study revealed some little known NMR (nuclear magnetic resonance) techniques developed by Professor G. J. Béné's group at the University of Geneva, Switzerland. These are suitable for use in weak, inhomogeneous magnetic fields. Laboratory NMR tests of numerous U.S. ore minerals showed good identifying signals from phosphates, fluorspar, bauxite, oil shale, and spodumene (lithium) ores, but not from the copper, lead, antimony or manganese ores tested. Use of EPR "signatures" for such ores is suggested. A conceptual design for an NMR assay logging system is proposed.

Jan 1, 1978

By L. H. McGuire, L. B. Berger

"During the period October 31 to November 4, 1944, tests were conducted by the Bureau of Mines in the Cascade Tunnel of the Great Northern Railway Cc. to determine the effects upon the tunnel atmosphere of the use of a Diesel freight locomotive through the tunnel. These tests were conducted at the request of the company to ascertain whether undesirable conditions might be caused by the discharge of Diesel engine exhaust gas in the tunnel, which was constructed for an electric haulage system and is not provided with equipment for mechanical ventilation. The use of Diesel locomotives on the division that includes the Cascade Tunnel was under consideration as a means of augmenting haulage facilities for the abnormal freight tonnage that must be handled during wartime.As the Bureau of Mines has received requests for information on the extent of contamination of the air of railroad tunnels by Diesel locomotives, this report was prepared to make available for general information the data obtained during the tests in the Cascade Tunnel. As the test locomotive is of a type used on other railroads, and as the bore and grade of the tunnel and the tonnages moved are comparable to such factors on other roads, the data should be sufficiently representative to be of general interest. The exceptional length of the Cascade Tunnel made it an excellent location for obtaining information on the composition of the tunnel air and on the movement of air induced in the tunnel by the passage of trains.The writers are indebted to C. O. Jenks, vice president of the Great Northern Railway Co., who arranged for the tests, and to the following personnel of the railroad who cooperated in the conduct of the tests: I. E. Clary, superintendent, Spokane Division, J. L. Robson, superintendent of motive power, oil and gas equipment, J. F. N. Gaynor, superintendent of electric operations, William Lowney, master mechanic, Spokane Division, and D. F. Marston and Verne Nelson, assistant superintendents of electric operations.The Cascade Tunnel is on the Spokane Division of the Great Northern Railway and pierces the Cascade Mountains some 49 miles west of Wenatchee, Wash. The west end of this division is electrified from Appleyard Station, 2 miles east of Wenatchee, to Skykomish, Wash., a distance of 73 miles. Until the described tests, only electric haulage had been employed through the tunnel since it was first opened to traffic in January 1929.The Cascade is the longest railroad tunnel in the United States - 7.79 miles. The tunnel is single-track, perfectly straight, concrete-lined, and is on an essentially uniform grade of 1.56 percent, ascending from west to east. The cross-sectional area of the tunnel is 314 square feet, the dimensions being shown in figure 1. Elevation of the east portal is 2,880 feet and of the west portal, 2,240 feet."

Jun 1, 1946

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By Ivor Hawkes

This report describes how longitudinal and bending stress waves in' percussive drill rods generate noise. It is shown that in practical drills the largest noise source is the bending waves, which are mainly generated because of imperfections in the piston, chuck, and drill rod alignment. Equations are presented which enable the noise spectra generated by the bending and longitudinal waves to be precisely predicted. Means for reducing the amplitude of the bending waves are discussed.

Jan 1, 1977

By R. H. Lien

The Bureau of Mines investigated a roast-leach process for recovering a marketable lithium product from a montmorillonite-type clay deposit located on the Nevada-Oregon border. The clay sample treated in the investigation contained 0.6 wt pct Li. The lithium recovery process consisted of several unit operations. The lithium silicate compounds in the clay were converted to Li2SO4 by roasting a pelletized mixture of clay, limestone, and gypsum at 900° C in a direct-gas-fired rotary roaster. Water--leaching the calcine at 40 pct solids extracted the Li2SO4. Lithium recovery from the leach solution involved concentrating the solution by evaporation, adding Na2CO3 to the concentrated solution to precipitate Li2CO3 , and filtering the slurry to obtain the product. The product filtrate was recycled to the evaporator following a crystallization step. About 80 pct of the lithium in the clay was recovered as 99-pct-pure Li2CO3. Process operating costs were estimated at $2.12/lb Li2CO3 produced; the current Li2CO3 selling price is $1.48/lb. Raw materials. accounted for 30 pct of the total operating cost.

Jan 1, 1985

By John Nagy

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 181 miscellaneous materials that present an explosion hazard. Data are given also for 50 dusts that present primarily a fire hazard and for 88 dusts that did not present an explosion hazard.

Jan 1, 1968

By W. E. Robinson

Samples of raw oil shale and kerogen concentrates were oxidized by alkaline potassium permanganate, air, nitric acid, oxygen, and ozone to obtain information about the chemical structure of organic kerogen in oil shale. In one test, oil shale and oil-shale products were oxidized exhaustively with alkaline potassium permanganate, and the distribution of the organic carbon in the final oxidation products was determined. Comparing results of this oxidation with those obtained from other carbonaceous materials and known compounds gave information about the structure of kerogen. Alkaline potassium permanganate oxidation also was used partly to degrade kerogen into soluble products for characterization purposes. Structures present in these degradation products were indicative of type structures originally present in the kerogen. Nitric acid, oxygen, and ozone were used also for partly degrading kerogen to soluble oxidation products. Carbon-balance oxidation tests using alkaline potassium permanganate showed that Colorado oil-shale kerogen differs from many other carbonaceous materials such as coal and kerogens from other areas. Composition of the degradation products indicated that Colorado oil-shale kerogen is predominantly cycloparaffinic and saturated heterocyclic structures with some long-chain paraffinic and aromatic structures present. The ring systems may be connected through short carbon chains or bridges containing oxygen, nitrogen, and sulfur.

Jan 1, 1963

By F. J. Cservenyak

The Bureau of Mines Solid Waste Program is directed toward three main areas of research: (1) Extraction of mineral, metal, and energy values from urban refuse; (2) recovery of mineral and metal values from wastes generated in the industrial extraction, processing, and utilization of raw materials and mineral-base products; and (3) upgrading and utilization of automotive scrap. The Bureau also has a contract and grant program which supplements the in-house research and aids in the training of personnel in the proper management of mineral- and metal-based solid wastes.

Jan 1, 1970

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace,4 the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is, although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931