Search Documents

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By Xavier B. Starnes

"INTRODUCTION The Krausse Estate property was the site of the first lead silver mining in western Kentucky, which began with the sinking of the Andrew Jackson shaft in 1835 3/. The earliest miners considered fluorspar of no value and threw it upon the waste dump, but Crittenden County later became an important part of the western Kentucky and southern Illinois fluorspar district 4/, which has produced about 90 percent of the fluorspar mined in the United States. By 1945, approximately 35,000 tons of fluordpar ore had been produced from the Estate property.This property can be reached by traveling west from Marion on Highway 60 from 2.5 miles, than northward 3 miles. The road from the paved highway to the mines is very rough but not impassable even in bad weather. Ore is hauled 5 1/2 miles by truck to custom mills at Marion, a town of 2, 000 population, where the Illinois Central Railway was a freight station.Hurricane Creek runs through the eastern part of the property. The surface slopes steeply upward to west from the creek, and the topography is rough. The top of the hill is about 150 feet above the creek.The climate permits working throughout the year, but spring rains cause surface water to enter mine and water apparently drains southward along the fractured fault zones, so that when no water is being pumped at properties north of the Krausse Estate a heavy flow comes on the Krausse."

Sep 1, 1946

By N. Kumar Kittusamy

A field study was conducted to evaluate seat designs on shuttle cars. Eight operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers also measured the levels of vehicle jarring/jolting. Four basic seat designs were compared on low and mid-coal seam shuttle cars during production operations at two underground coal mines. Two seats were currently used on the shuttle cars and another two were NIOSH designs. Objective data were collected using accelerometers with pre-amplifiers and filters connected to a data recorder; whereas subjective data were gathered with a visual analog scale (VAS) and a questionnaire. Results from measured levels of jarring/jolting showed that the NIOSH Seat L2A smoothed out bumps better than any other seats. Using the VAS, mid-seam and low-seam shuttle car operators rated the levels of jarring/jolting and discomfort lower with the NIOSH seat than the other seats. Questionnaire responses indicated that operators rated NIOSH seat designs as more comfortable. This research will provide the industry with better seat designs for isolating jarring/jolting in vehicles. Furthermore, researchers plan to improve the NIOSH seats using information gathered in this study.

Jan 1, 2003

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By JOE SIERAKOSKI, W. R. Hardwick

This paper , which describes mining methods and practices at the Johnson Camp copper -zinc mine , Coronado Copper & Zinc Co. , Cochise County , Ariz . , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . Johnson Camp is in the eastern foothills of the Little Dragoon Mountains in secs . 23 , 24 , 25 , and 26 , T. 15 S. , R. 22 E. ( fig . 1 ) . The mining property is in the low, rolling foothills at an altitude of slightly over 5,000 feet above sea level ( fig . 2 ) . The area is covered with scattered grass and small desert shrubs . The climate is mild , with hot summers and mild winters . The average annual precipitation is about 12 inches . The nearest surface water is the San Pedro River , some 12 miles west of the mine . The property is owned by the Coronado Copper & Zinc Co. , Los Angeles , Calif . This report gives a brief history of the property , describes the general geology of the area and of the ore deposits , outlines the methods of prospecting and exploration , and gives the methods of sampling and of estimating ore reserves . Development and stoping methods are explained . Underground transportation , ventilation , mine drainage , and safety measures also are described . The last section gives a brief description of the milling practice .

Jun 1, 1957

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972

By Paul M. Tyler

The outstanding trend in the graphite market is the fast-growing demand for cheaper qualities of graphite and the declining consumption of the more expensive varieties. The manufacture of graphite, crucibles for melting metals was one of the earliest applications of the-mineral and for many years constituted by far the leading source of demand. In later, years, however; and more especially since the Great War, the increasing demand for high-grade steel ingots and castings instead of enlarging crucible sales has permanently curtailed the domestic demand for crucibles because it has hastened the introduction of electric, oil or gas fired furnaces to replace the older types requiring pots to hold the metal during melting. While there has been a substantial increase in the use of graphite for miscellaneous refractories the total consumption for such purposes is too small to offset the shrinkage in demand for crucible making, and though it consumes the better and hence more expensive grades of crystalline flake graphite, it does not call so insistently for the still costlier Ceylon grades.

Jan 1, 1929

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By F. B. Tough, B. H. Scott

"Petroleum engineering is a comparatively new branch of engineering, with which few people, even petroleum operators and mining engineers, are thoroughly familiar. Petroleum engineers are responsible for the accurate keeping of well logs and all pertinent data upon formations encountered, for the careful analysis of such information, and recommendations as to most suitable places for drilling, for detailed study of methods of drilling, casing, and so on in order to obtain maximum production for a minimum cost.The Bureau of Hines has from time to time carried on work in all branches of petroleum engineering in the various fields of the United States. Such work is also being carried on extensively by the California State Mining Bureau, which has in its employ a number of men who have had, besides their technical training, actual experience in oil field work. This is about the only state at the present time which is carrying on this work in a definite way. It has therefore been the practice of the employees of the Bureau of Mines to go to other states and give such advice and assistance as might prove of value in development work and in prolonging the production of the fields."

Jan 1, 1920

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By Mary F. Koehler

Continuing a program of thermochemical investigation of compounds of to ferroalloy elements, this paper contains ins values of the heats of formation of two sodium molybdates (Na2Mo04 and Na2Mo207) and three sodium tungstates (NO2W4, Na2W207, and NA2W207, and Na2W4013). The experimental method was solution calorimetry. The solution medium was sodium hydroxide solution, except that hydrofluoric acid solution was used for sodium tetratungstate. The heat of formation values are given with reference both to the constit¬uent elements and to the constituent oxides. These data are of prime impor¬tance in the thermodynamic consideration of these substances, as their accumulation includes the most difficult and time-consuming steps toward evaluating the free energies of formation and thus the potential reactivities and thermal stabilities. Except for values for sodium monomolybdate and monotungstate, no previous similar data were contained in literature sources.

Jan 1, 1962

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Floyd County in beds 28 inches or more thick, in thousand tons, is as follows: [ ]

Jan 1, 1958

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By Fredrick L. Johnson

Tungsten is the principal mineral commodity in the Laurel-McGee RARE II area; copper and molybdenum would be recovered as by-products with the tungsten. Indicated and inferred tungsten marginal reserves at the Hard Point Mine (fig. l, no. 10) are 16,000 tons (14,000 t) averaging 1.0 percent tungsten trioxide (W03). The mine is outside the RARE II area, but the geologic structure that it is on extends into the area. Indicated subeconomic zinc, silver, copper, and lead resources at the Lucky Strike Prospect (fig. 1, no. 7) are nearly 6,200 tons (5,600 t) averaging 5.45 percent zinc, 0.5 oz silver per ton (19 g/t), 0.40 percent copper, and 0.32 percent lead. Although tungsten has been produced at the Tiptop Mine (fig. 1, no. 12), resources were not calculated because of the spotty nature of the tungsten mineralization. Additional exploration at the Tiptop and Hard Point Mines could reveal significant resources. The potential for tungsten resources at the Payday Prospect, Tungsten Prospect, and Morhardt Mine is also high. The Pine Creek Mine custom mill, located about 35 mi (56 km) southeast, could process tungsten concentrates from the area. Tungsten production has been recorded from three properties, the Hard Point, Morhardt, ant Tiptop Mines. Output was about 405,000 lb (184,000 kg) of W03, nearly all from the Hard Point.

Jan 1, 1983

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By Lewis M. McNay

The strength characteristics of hydraulic sandfill modified by varying quantities of type III portland cement and two flocculants were investigated by the Bureau of Mines. Three different sand-cement ratios were examined using different percentages of flocculant. Two other experimental variables were curing time and weight-percent solids for hydraulic mixture. Results of unconfined compression tests with strain are discussed. Maximum strength was achieved with 0.5 weight-percent of ferric sulfate per ton of solids when the slurry mixture was 75 weight-percent solids. The bearing capacity of hydraulic sandfill is reduced by increasing the water content and decreasing the amount of cement mixed with sandfill.

Jan 1, 1976