Search Documents

By Clarke E. Schuetze

This project had as its objective the experimental investigation of water capsule production utilizing the Southwest Research Institute's submerged nozzle encapsulation apparatus (U.S. Patent 3,389,194). Initial efforts on this project involved nozzle configuration and shell formulation optimization. The shell formulation developed on a prior program was modified during the course of the project to obtain the best balance of capsule breakage resistance and water retention. Subsequent effort centered on determining operating conditions which would produce the best quality capsules for each candidate shell formulation as determined by laboratory tests. Some preliminary work was done to increase the production capacity of the encapsulation equipment. The program was extended with major emphasis concerned with scale-up studies of capsule production capacity and the treatment of problems associated with grouting cartridge fabrication. During the course of the program, water-containing capsules were produced which have good long-term water retention, block resistance and adequate strength. Using a single-nozzle design, a production capacity of 15.9kg (35 pounds) per hour was demonstrated to give acceptable capsules based on initial results.

Jan 1, 1978

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By P. C. McWilliams

Theoreticians in soil mechanics have been pursuing a probabilistic approach to the factor of safety of an embankment or darn for the past 10 years. The motivation for this work is in contrast to the current practice of deterministically computing a factor of safety and treating it as an absolute with no regard to its inherent statistical variability. Basic to the probabilistic approach is the selection of an appropriate statistical model to represent the histogram or probability density function (PDF) of the factor of safety values, Rather than simply assuming which PDF is appropriate, the Bureau of Mines collected data at two waste disposal embankments for consideration, This report addresses three candidate models, using the techniques of nonlinear curve fitting, and identifies the "best" model. A propagation of error formula for estimating the variability of Fellenius? factor of safety is also discussed.

Jan 1, 1983

By James L. Elder, J. P. Capp, James J. Dowd

The Bureau of Mines and the Alabama Power Co., jointly, conducted the first experiment undertaken in the United States in underground gasification of coal in place, at Gorgas, Ala. Milton H. Fies, manager of coal operations, Alabama Power Co., proposed the cooperative investigation to Arno C. Fieldner, chief, Fuels and Explosives Branch, Bureau of Mines; and assisted in supervising the experiment. The objectives of the experiment were to determine whether coal in place could be burned successfully and whether the burning could be controlled; the effect of the fire on the coal bed and the overlying strata; and the yield and quality of gas that could be obtained.

Aug 1, 1947

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the past 12 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development, of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By G. R. Hopkins

The average gravity of the total crude petroleum produced in the United States during; the year 1927 was 32.2° A. P. I., or 0.864 in terms of specific gravity. A similar study, made by the U. S. Geological Survey in 1921, gave the average gravity at that time as 32.0.° To one who is accustomed to thinking of crude petroleum in terms of Oklahoma-Kansas and North Texas trades it may be surprising that the average gravity for the entire country is no higher than 32.20. The chief reason for this apparent discrepancy lies mainly in California production, which in 1927 amounted to over 25 per cent of the total, but which had an average gravity of only 24.10. A factor of less importance was Arkansas, which, though on the decline as a producing State, exerted a material effect by reason of its average gravity of 21.6°, the lowest for any State. In view of the heavy production of light crude in the Seminole area of Oklahoma during 1927, it would appear that the average gravity should have shown more than a 0.2 per cent gain over 1921. That this did not occur was due to the fact that in the interim between 1921 and 1927 important heavy oil discoveries were redo, notably the Smackover field of Arkansas.

Jan 1, 1929

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By Melford H. Salsbury

The maximum net return from the sale of ores and concentrates of gold, silver, copper, lead, and zinc accrues to the producer when these mine products are marketed to the best advantage. Data are presented that the producer, especially the small mine operator, can use to survey available markets and make a preliminary estimate of the net return to be expected from an ore, on the basis of typical mill, smelter, and freight schedules. A review of the industry is presented by States in which recent production statistics are given, marketing facilities are discussed, and locations of principal mining districts, custom mills, and smelters are shown. Explanations of treatment processes, ore types, treatment charges, payments for metals, and deductions are given. Published rail and truck freight rates for mine products, based on marketing patterns developed over many years, are listed and explained.

Jan 1, 1964

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By J. P. Powell

The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Mid continent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also. The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County, Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that could not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 1.36 million barrels of water had been injected.

Jan 1, 1953

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/ lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978