Search Documents

By John Babcock, Gregory Poole, Ron Hudson

In January 2007, Fultondale Alabama opened a new elementary school. Site work at the old school location included blasting activities and the old school building was scheduled for demolition. With help from Apache Construction, blasting was scheduled to be performed in close proximity to the old school building prior to the demolition. Arrangements were made to perform extensive monitoring on the old school building during the blasting activities. The monitoring plan for the project included: • Pre and post blast inspections were performed on the structure; • Conventional crack monitors were installed at 22 locations throughout the structure; • Digital displacement monitors were installed at 6 locations on the structure; and • Seismographs were used to monitor structure vibration at 6 locations and ground vibrations at 9 locations. Blasting activities were allowed to produce vibration levels well above the safe levels established by the U.S. Bureau of Mines (USBM). Vibration levels up to 7.44 in/sec were recorded with no damage noted. Permanent deformation was recorded on vibration levels of 9.68 and above. Not only did this project reinforce previous studies which indicate that concrete block walls can withstand vibration levels well above 2.0 in/sec, this study was also a good example of employing new technology to help determine if/when damage occurs on a specific structure.

Jan 1, 2009

By Gregg A. Scott, Gordon F. Revey

"The Folsom Dam is a 340-foot-high concrete gravity dam with embankment wing dams located on the American River about 20 miles northeast of Sacramento, California. Folsom Dam is operated andmaintained by the U. S. Bureau of Reclamation (Reclamation). As part of the Central Valley Project,Folsom Dam is a multipurpose facility providing water supply storage, flood control, power generation, and recreational opportunities."

Jan 1, 1999

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By Tom Snyder, John Brulia

Part I is the first of a series of articles by the authors on hazardous materials (HM) transportation safety and compliance for shippers and carriers who offer and transport commercial explosives in commerce on public highways in the U.S.

Jan 1, 2014

By John Brulia

It has been said that the only thing that remains constant is change. After more than 33 years in the explosives industry, I do not take any exception to that adage. I have seen changes in people, changes in ownership of companies-both small and large, domestic and international; changes in products; changes in the way we use products; changes in the way we handle products; changes in regulations; and last, but not least, changes in our perceptions of threats to our industry.

Jan 1, 2008

By Mark Abernathy

When most people think of a motor vehicle accident, the direct costs resulting from that accident, such as vehicle repair or towing charges, are generally easy to quantify. However, the indirect costs associated with an accident are often overlooked. These indirect costs can take a tremendous toll on a company in more ways than you might think.

Jan 1, 2006

By Kwang-Tae Kim, Yong-Kun Choi, Jeong-Soo Chong, Yun-Jae Lee

An annex building at the former Agency for National Security Planning(NSP) complex located in downtown Seoul was demolished by progressive collapse method. This work was done as a part of efforts to restore the landscape of Namsan Mountain which lies in the Center of Seoul. The five-story reinforced concrete structure was razed in 5.5 seconds by the 29kg of high powered explosives which were placed in some 320 holes in the building with floor area of 2,577 m². The asbetos and all the other finishing materials in the building were removed before the demolition and the specially coated wrap minimized the spread of blasting dust. Seismic and air overpressure waves were monitored at 8 points, which were below safety limits and the continuous communication with neighborhood prevented any complaint.

Jan 1, 1998

By Tristan Worsey, Nathan Rouse

Florida legislature allocated funding for the Florida State Fire Marshal to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains.

Jan 1, 2019

By ATF Publications

The following is a summary of the changes that were incorporated into the new Federal Explosives Regulations, 27 CFR Part 55, dated 9/2000. However, in light of the recent events of September 2001, additional changes in the Federal Explosives Laws and Regulations may be forthcoming. The nature and extent of any such potential changes are impossible to gauge at this time. However, this synopsis of the changes contained in the September 2000 Orange Book, ATF P 5400.7 was current at the time of this writing. Any questions regarding this paper should be directed to the Public Safety Branch in ATF Headquarters in Washington, D.C.

Jan 1, 2002

By Robert B. Hopler

Reefs, exposed rocks, and fast currents made the Hell Gate section of New York's East River a treacherous passage ever since man attempted to sail through the area. As the harbor's importance grew, attempts to improve the channel were made, starting in 1851. This paper discusses the first major organized effort to clear the area, which began in 1869 and culminated in a single large blast in September 1876.

Jan 1, 1981

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By Douglas A. Anderson

The simplest method used to predict ground vibration from blasting is scaled distance -the distance from a blast divided by the square root of the Pounds per delay. Pounds per delay is defined as the number of pounds of explosive detonated within an 8 millisecond (ms) interval. Based upon this definition, regression plots of peak particle velocity vs. scaled distance have been used to determine likely values of peak particle velocity.

Jan 1, 1989

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

By Ethan Steward, Kyle Perry

Underground coal mines have several dangers, one the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. These seals must be designed to withstand different pressure levels based on the potential of the atmosphere behind the seal to become explosive, either 50 psi (345 kPa) for inert atmospheres, 120 psi (827 kPa) for non-inert, and over 120 psi (827 kPa) for special cases. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at a high velocity causing them to impact and damage the mine seals. Seals damaged in this manner may no longer hold the pressure they were originally rated for and may fail during subsequent explosions or leak explosive gasses into active workings. To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals. The velocity of each projectile is measured by an infrared chronometer which can later be used to determine its impact energy. Impact effects on the seals are measured using strain gauges, LIDAR scans before and after impact, high speed cameras, and visual inspection. The focus of this paper is on the projectile generator design and initial testing.

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By Jeff Dean

As the Society celebrates its 35th year as an explosives industry association, it is clear that we are part of an industry that covers many sectors of economic activity. We are the voice of those who use, transport, store, manufacture, and dispose of commercial explosives products and others that serve the end user of explosives products. Along with other associations in this industry, we have a combined membership of hundreds of companies and tens of thousands of individuals in the U.S. and around the globe.

Jan 1, 2010

By Bill Williamson, Doug Richmond, Kerri Kuntz, Gus Gilman, Larry Heywood

This was a description by the poet of what occurred over two centuries earlier to Hannibal’s troops as he passed through the Alps. Interestingly, the pass that many feel is the route that Hannibal chose, Col de la Traversette, is the sight of possibly the earliest avalanche mitigation known. Monastery records describe a tunnel built in 1470, near the top of the pass designed to protect pilgrims from the upper slopes. For the next several centuries, avoidance and reinforced structures were the primary tactics to defend from avalanches

Jan 1, 2009

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Kagan Ozdemir

In the condition that drilling and blasting technique is inevitable depending on the rock mass and material characteristics on mining activities, the fragmentation rate and particle size distribution of the muckpile after blasting has important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc. and the total costs of that mine. Drilling and blasting is an important step in this process chain and it's results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. There is an increasing body of blasting research indicating significant impacts in these downstream processes.

Jan 1, 2007

By R J. Johnson

The development of "SANFO" has provided the Mining Industry with a LOW COST HIGH GAS VOLUME, VARIABLE DENSITY, Blasting Agent which can be blended "On Site" in a simple Agitator mixing and charging system by mine site employees.

Jan 1, 1996