Search Documents

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

By James W. Reil, Douglas A. Anderson, Steven L. Burchell

A total of 26 full-scale production blasts at three sites were extensively monitored with sophisticated instrumentation systems to determine the benefits of more accurate detonators. The new and more accurate MS electric Masterdet detonator was tested against conventional detonators to determine any increase in productivity outputs. All blast design parameters between paired blasts were kept as constant as possible with the only difference being the inherent accuracy of both detonator systems.

Jan 1, 1986

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By Rowan A' Murry Karstel

One way to ensure dragline productivity is by Increasing the size of the dragline bucket. In August 1994, Optimum Colliery in conjunction with Van Reenen Steel, Northwest Applied Technology, SSAB of Sweden and Barlows Equipment launched the new lightweight dragline buckets. Optimum built the first prototype bucket that was used for the deslgn for future buckets. After knowledge had been gained from measuring the input force of the bucket Northwest Technologies designed the new bucket with finite element analysis. Together with the knowledge of quenched and tempered steel from SSAB of Sweden and Barlow Equipment, the new Wrightech bucket was born.

Jan 1, 1998

By Catherine T. Aimone-Martin, Meyers Joseph A.

A new strain-based criteria is being adopted for rock blasting in New York City (NYC). This criteria is based on several years of research involving vibration measurements of tall structures during blasting within several feet from buildings designated historic and Landmarked. This research has demonstrated that tall, heavy structures show little upper-structure vibratory response during hard-rock, urban blasting carried out in NYC. The Fire Department of New York City (FDNY) permits rock blasting and regulated limits for ground vibrations using the U.S. Bureau of Mines (USBM) safe blasting criteria. However, these regulations are often superseded by a 0.5 in/s (12.7 mm/s) limit imposed by the New York City Department of Buildings for historic and Landmarked buildings that are adjacent to the majority of blasting projects in the City. This onerous limit is often exceeded resulting in frequent stop work orders that increase the cost and time of rock excavation projects. The

Jan 1, 2019

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By Joshua A. Bennett

"Lawsuits where owners allege their property has been damaged by nearby blasting routinely costblasting companies, explosives engineers, and others in the field both time and money. When ownersfeel the vibration of a blast, they immediately begin to look for damage and usually find cracking thatwas, in fact, present prior to the blasting occurring. When those owners begin to talk to their neighbors and legal counsel, blasting entities suddenly have multiple lawsuits being filed as a result of the same blast."

Jan 1, 2016

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By P D. "Takis" Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of the stemming and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transition. Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1991

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006

By W. J. Birch, D. Leckenby, R. Farnfield

The use of electronic detonators to improve fragmentation is becoming universally accepted. However their use in limiting peak particle vibrations levels is still in its infancy. Most of which is anecdotal, in that few actual scientific studies have been carried and published. This paper details the research work carried out at a limestone quarry in the County of North Yorkshire in Northern England. Here a series of blasts were carried out some used non-electric detonators whilst others used electronic detonators. The majority of blasts were carried out at the same burden, spacing and deck charge weight loadings. Initially, the key variable was the difference in detonator type and then leading on to using the electronic detonators at specific exact different detonator timing intervals. Later the study was extended to include double row as well as single row blasts.

Jan 1, 2007

By Claude Cunningham

Difficulty has always attended the evaluation of rock breaking energy available from explosives, owing to the complexity of the way in which it is released, and the destructive amplitude of the pressures. Many problems have arisen and continue with this difficulty, including the following: I. Formulation of improved compositions to deliver appropriate energy levels to the blasthole walls, or to deliver previous results at improved cost. How appropriate is it to use various ingredients, such as Aluminium, water, salt? 2. Claims over energy issues, resulting in wasted time and expense, over things that sound good in theory but are very difficult to tie down. 3. Purchasers of explosives make decisions based on claimed “Bang per Buck” from different manufacturers, where the estimate of “Bang”comes from simplistic numbers from various, very unequal detonation codes. The above problems are escalating as time progresses. Using the high level IDeX PC 2000 detonation code, we have found a way to portray the differences between formulations in a way which relates to their breaking effect in the field. The basic method is to plot the adiabat from the detonation state to full expansion in units which express the practical implications. Energy alone cannot deliver results, so we use the curve to examine its manifestations: pressure and temperature. Internal energy is plotted with these. The method displaces relative energy numbers, as it portrays the context in which the energy is available. It is used here to compare an ANFO, an emulsion and a doped emulsion, as well as the effect of Aluminium. The effect of the shock pressure regimes and temperature correlate well with what is seen in the field.

Jan 1, 2000

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By Joshua Taylor Drake

This report answers specific questions concerning underwater blasting considerations, and blasting safety. The blasting considerations discussed consist of basic blasting principles, and new variables to be accounted for. Blasting safety will include the safety of personnel and structures. The environmental considerations will also be discussed with mitigation methods. To be most effective, this document requires the reader to be familiar with key fundamentals of explosive engineering. In order for a blasting professional to benefit from this report, the following questions will be asked:

Jan 1, 2015

By Mark A. Williams

"This paper was originally intended to be a presentation of a case study of two surface bituminouscoal mines in the southern Appalachian coal fields located within five miles of each other. These mines were nearly identical in every aspect from geologic setting to equipment application. Althoughrepresentatives from each mine desired to participate in the preparation of this paper through support in providing background information and in review and editing, it was later concluded that, due to the environmental sensitivity associated with each mine, it may not have been a good decision to present this case study in a public forum."

Jan 1, 1994

By Jackson R. Pressley, M L. Hopkins, R E. Danell, N T. Moxon, Andrew Bowman

Efficient and cost effective blasting is achieved by closely matching the explosive energy to the strength of the material in which it is being used. Although there are many empirical relationships wich approximate this situation complete the blast optimization can only be achieved by quantitatively assessing explosive/rock interactions and explosive performance. The performance of an explosive is essentially governed by its velocity of detonation or the rate at which the detonation wave travels through the explosive column.

Jan 1, 1991

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation.

Jan 1, 2001