Search Documents

By Bryan Papillon, Karl Christopherson

In order to improve vibrations from quarry blasting, a new technique and timing pattern was established and applied to the particular geology. By shooting a single representative borehole one full second ahead of the production blast, a signature waveform can be isolated and analyzed. Multiple productionsignature blasts were performed. Encroaching residences require quarries to adjust their blasting techniques to reduce vibrations and raise frequencies. A signature hole inherently poses problems to quarries. Blasting one single hole from a production bench poses safety issues to wall stability; vibration issues to close neighbors; and budget issues to the quarry operator. Results showed that the new timing pattern reduced vibrations through timing optimization without a loss in quarry production. Therefore, this technique of vibration analysis employing a production-signature hole is successful in creating a timing pattern that meets the quarry’s goals.

Jan 1, 2008

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

By Cathy Aimone-Martin, Frank Achuff

The New Mexico Department of Transportation (NMDOT) and the Federal Highway Administration (FHWA) have let a contract to Sierra Blanca Constructors for a design / build contract along 38 miles US 70 in Lincoln County, New Mexico. The project will improve safety of travel along the corridor and facilitate the adopted economic development goals of the state. Proposed improvements include widening the existing highway from two lanes to four lanes, providing left turn lane options at selected locations, improving access for businesses and residences, aesthetically enhancing retaining walls, improving storm drainage and replacing the existing pavement with a 30 year mechanistic imperialistic perpetual pavement design. The US 70 Hondo Valley highway project is situated in a narrow valley with steep limestone walls, passes along a Scenic Byway and numerous historic ranching communities with structures that date back three centuries. The scope of work included requirements to monitor and mitigate blasting, noise, and vibrations. The contract was very presumptive with regard to blasting design and procedures. These included visual impact mitigation to treat and stabilize slope cuts, the Migratory Bird Treaty Act protecting roosting and nesting birds from airblast, and the protection of historic and cultural features such as acequias, wells, and structures. Public involvement affecting the rock blasting design has come from citizen task forces and committees concerned with highwall aesthetics and preserving the scenic byway and cultural resources. Constraints placed on the blasting program from agencies and the communities are often at odds. For instance, blasting must produce stable yet natural-looking walls to preserve aesthetics. Restrictions have been placed on pre-splitting and smooth-wall blasting yet safe slope are of the highest priority. This paper presents details of the design/build process undertaken by the contractors to conduct blast rock in an environmentally sensitive region. Blast designs consistent with good construction practices and used to comply with the many federal and state highway stipulations are described.

Jan 1, 2004

By Blair Jackson, Tjaart Louw

Martha Mine, owned by Newmont Mining, Australia appointed Macmahon Contractors (NZ) Ltd as the mining contractor to drill, blast, and crush and convey ore for processing, followed by construction of a tails dam facility from the waste material. The open pit is located 140km(90miles) south east of Auckland, New Zealand in the middle of the township of Waihi (the main street of the town with a population of 3,500 is 90m from the perimeter of the open pit mine). Mining must proceed at 325,000m3 (of which involves blasting approximately 11,000 holes per month, in order to ensure continued ore supply.

Jan 1, 2003

By Robin L. Simmons

Mining in the Genesis open pit has been conducted above the active haulage and ventilation declines of the Deep Star underground mine. Production has continued in both mines. The Deep Star haulage and ventilation declines, the primary and secondary egresses respectively, had to remain open and safe for travel until the new haulage and ventilation accesses were completed. Eventually, the upper 350 feet in each decline will be removed. The declines are in relatively competent calc-silicate hornfels with several high-angle, northeast-striking, clay-filled or open-spaced fault zones that create localized areas of poor ground requiring steel sets. To maintain the integrity of the declines, blast-induced vibration levels and damage were monitored in both declines after each surface blast. Seven geophones were installed in the declines to monitor peak particle velocity and peak vibration frequency. These data helped design subsequent blasts and predict expected vibration and damage levels. Blast design modifications included reducing the pattern size, reducing the powder factor and limiting blasthole detonations per delay. While limiting blast-induced vibration, these blast design modifications had to allow effective surface mining to continue. Linear regression analysis of peak particle velocity and scaled distance was used to determine the scaled distance necessary to keep the peak particle velocity under 2 inches per second. To date, the new ventilation raise, which is also the secondary escapeway, has been established and safe conditions were maintained in the original ventilation decline. Data collection and conscientious blasting procedures continue above the haulage decline.

Jan 1, 1998

By Curtis G. Kremer, Jeffrey L. Brummert

Blue Circle Cement's Ravena, New York quarry mines approximately 6.7 million tons of limestone per year. Blasting occurs approximately twice a week on three separate benches. Shots average 60,000 tons but can range up to 140,000 tons. Ongoing scrutiny of the drilling and blasting program allows for maximum blast efficiency which results in lower overall mining and crushing costs. Close cooperation between management and explosives supplier assures Blue Circle Cement's objective, "To develop, implement, and continuously improve a measurable drilling and blasting system that will optimize the total mining and crushing costs while ensuring compliance to safety and maintaining or reducing the environmental impacts of blasting".

Jan 1, 1994

This is the story of a blast - not a large blast by todays standards as it only involved a total of approximately 50 cubic yards of rock. Nor did this blast involve any new or revolutionary blasting technique or require involved analysis or the applications of rock mechanics theories. Instead, it was a blast that involved the tried-and-true principles of good blasting: precise alignment of blastholes; selection of explosives and detonators designed for the conditions encountered; extreme care in loading and hooking up and the use of several ingenious devices and techniques to achieve the proper loading and firing of the blast

Jan 1, 1976

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025

By Alan R. Cameron, Alastair C. Torrance

An explosives underwater test facility has been established and commissioned in the Hunter Valley, New South Wales, Australia which allows the measurement of the actual shock and gas energies of the explosive

Jan 1, 1990

By Joshua Hoffman, Braden Lusk, David McLane, John Rathbun

The research conducted previously on Shock-Tunnel Waveform Analysis gave a brief insight into the propagation of a shockwave within a shock-tunnel compared to that of an open air arena test. As a refresher, a shock-tunnel is an energy channeling device used to simulate the effects of a large scale detonation with significantly smaller charge weights; having the ability to conduct tests in this fashion can greatly reduce the costs of testing products.

Jan 1, 2012

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By Frank Hirthammer

"Nowadays, security in the lifecycle of explosives is more important than ever. Terror attacks all over theworld pushed the EU to decree a Commission Directive for the identification and traceability of explosives that set a series of requirements for involved manufacturers, distributors and end-users. The challenge was to find and implement a track and trace system for all concerned European companies byApril 5, 2015. Since then, countries worldwide have followed this example and implemented similarregulations."

Jan 1, 2017

By Nicholas Matthews, Vilem Petr

This project will report findings on the establishment of a new surface test site at the Colorado School of Mines Edgar Mine. Concerns over the blast effects on site neighbors prompted the study to be conducted. The current maximum charge weight of 20-lb was studied to ensure that all environmental effects were within the range prescribed by state and federal regulations. Geophone locations were surveyed using GPS and monitored using Instantel Minimate Plus instruments. Distances and orientation of measurement sites to the test site were varied according to the local geography and geology. Weather conditions were also observed and recorded during all tests. Neighbor complaints were recorded and taken into account during analysis. Current results show that the current charge limit results in a safety factor of over 200 for all blasting activities at the site. Data collection is ongoing and a review is to be conducted annually. These results will be presented in the future. Results are presented and discussed in the following paper. Copyright

Jan 1, 2010

By Frank Huber, Ed Fulop, Neil Singh, Ron Elliott, Blair Gohl, Lewis Clarke

This paper covers the successful application of explosive compaction technology for the densification of the foundation soils for the seismic upgrade of the Seymour Falls Dam, Vancouver, BC. The original earthfill embankment constructed during 1958 to 1961 was upgraded in 2004 to 2007 to withstand the effects of a maximum credible earthquake. This paper provides general background information on the theory of the explosive compaction of soils, history of use, geology of the site, project constraints, explosives selection, blast designs, instrumentation used, problems encountered and solutions implemented, and the results achieved.

Jan 1, 2009

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By David E. Siskind

In the period 1989 to 1994, the U.S. Bureau of Mines assisted the Office of Surface Mining, Reclamation and Enforcement (OSM) in studying a high-complaint situation near an active surface coal mine. As part of a review for its project report, the Bureau had to address issues on the adequacy of the safe blasting criteria and analysis procedures in its 1980 report RI 8507, Structure Response and Damage Produced by Ground Vibration From Surface Mine Blasting.

Jan 1, 1996

By J. D. Aubertin

Rock blasting is a complex engineering process that requires in-depth knowledge of operations and geomechanical conditions. Acknowledged design precepts are based on cratering behavior associated with stiff hard rock masses. Other cratering mechanisms may however arise under certain geomechanical conditions such as extremely fractured rock masses, or with soft rocks such as rock salt and potash. The burden dimension also plays an important role in the prevalent cratering mechanisms of a given blasting condition. The present article investigates the variability of cratering profiles and geometrical trends based on characteristic geomechanical differentiation and considering the influence of burden. The differences in observable mechanisms are examined through small and large-scale single hole blast (SHB) tests. SHB tests involve a series of individual shots blasted parallel or sub-parallel to an open face. The burden dimension is varied to obtain burden dependent characteristic trends. The breakout shape is represented by a crater model in the form of a power law equation capable of describing prismatic, concave and convex cratering. The formulation comprises two reference index parameters that can describe the geometrical and geomechanical conditions. SHB test campaigns conducted in rock salt, limestone, massive amphibolite, pinolite, and grout blocks are compiled in quantitative manner to demonstrate the influence of geomechanics on cratering profiles. The observed trends are corroborated through numerical modelling carried on Finite Element Model (FEM) LS Dyna to investigate the prevalence of specific cratering mechanisms. A series of SHB tests at large and small burden values are also used to showcase the influence of geometry on the prevalent cratering mechanism and the resulting crater

Jan 1, 2024

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000

By R. K. Wharton, G. H. Pickering

The paper reviews the explosives products that have been certified by the different Explosives Notified Bodies for sale in European Union countries. The development of harmonised standards for explosives is also discussed as are recent developments relating to certification and a possible forthcoming Directive on pyrotechnic articles.Copyright

Jan 1, 2004

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000