Search Documents

By G. Y. Zhou

During Zijinshan copper heap bioleaching, pyrite was leached in plenty resulting in high ferric concentration in solution. It has affected bioleaching and extraction processing greatly. It results much acid and iron in solution and bad effect to extraction processing. The paper studied the influence factors in the course of pyrite leaching and ferric ion chemical oxidation, especially studied the redox potential for copper bioleaching so as to find key factors affecting the dissolution difference between chalcocite and pyrite. The results show that the redox potential is important factor. Copper and pyrite leaching rates are 95% and 11% respectively and there is great dissolution difference between them at redox potential 700 mV (SHE). During pyrite bioleaching, the indirect action of bacteria gives priority to bioleaching cooperating with the direct attack of microbial cells attached to the mineral surface. Redox potential is determined by ratio of ferric and ferrous, ferric in solution was supplied by the way of oxidation of T. f bacteria, sufficient bacteria concentration and active character were two vial factors of controlling redox potential. It is indicated that copper can be selectively bioleached during copper bioleaching by controlling redox potential of bioleaching. The conclusion will provide theoretic foundation on balance of acid and iron during bioleaching for copper of higher S/Cu ratio. The experinment proved that bacteria activation was decreased on condition of both low pH value and intermittent aeratation during bioleaching. It resulted that the oxidation velocity of ferrous ion was decreased and redox potential was controlled. The dissolution of pyrite was depressed. It would be possible to actualize selective leaching of secondary sulfide copper ore during bioleaching process.

Jan 1, 2014

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By Ghislain Bournival, Cagri Emer, Seher Ata

"It is well known among flotation practitioners that the contact angle can be correlated with the amount of material recovered from feed by flotation. The contact angle of solids can easily be modified by the addition of a collector. However, some collectors also have frothing properties thus altering the solid and bubble surface properties simultaneously. To avoid this problem, a technique has previously been used in which silanol groups are attached to the surfaces of the particles, but this method has its own problems. In this work, silica particles with various surface hydrophobicities were prepared using an esterification process. By using alcohols with different hydrocarbon chain lengths, from 4 to 12 carbon atoms, surfaces with a wide range of contact angles could be prepared. The technique was used in the modification of silica particles that were tested in a fluidized bed flotation column, and a laboratory mechanical flotation cell. In parallel experiments, dodecylamine (DDA) was used as a collector. It was found that irrespective of the type of flotation machine and surface preparation method, there was a close correspondence between flotation recovery and the contact angle of the particles. The silanation process has known drawbacks relating to the presence of moisture during the reaction, and the stability of the silane coating after it is been prepared. Esterification does not suffer from these disadvantages. This work has shown that the esterification technique is a robust alternative method for preparing hydrophobic quartz surfaces."

Jan 1, 2014

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By Y. G. Zhu, G. B. Zheng, Z. B. Qian, X. R. Zhang, A. J. Ren

"Based on PMA polymer, two kinds of novel macromolecular depressants, PMTA and PMA-PDTC, were designed and synthesized. PMTA was used for desilication in hematite reverse flotation. PMA-PDTC was used in the separation of Cu-Pb concentrate as galena depressant. The micro-flotation results showed that PMTA exhibited a good depression performance compared to starch. We found that 98.29% of hematite was depressed with a grade of 65.24% at pH 11 with 12 mg/L dosage. The flotation separation results of Cu-Pb concentrate demonstrated that PMA-PDTC was an effective depressant for galena in separating galena from chalcopyrite. When IPETC was used as collector, at pH 8.5, the flotation separation tests demonstrated that Cu concentrate was obtained with a grade of 28.89% containing 12.12% Pb.INTRODUCTIONThe role of depressants is crucial in the separation of oxide or sulfide minerals, for example, the desilication in hematite concentrate and the separation of Cu-Pb concentrate.It is well known that, in current reverse flotation processing of hematite, starch is a traditional depressant for hematite. Most research focus on the modification of starch [1-3]. Although its depressing ability is enhanced in some extent, its own shortcomings is still existed. So, it is important to develop a new hematite depressant instead of starch.In the separation of chalcopyrite and galena, because of their extremely similar floatability, it is difficult to realize the separation of these two minerals. Traditionally, there are two methods widely used in the separation of Cu-Pb concentrate by depressing chalcopyrite with cyanide [4] or depressing galena with dichromate [5] in most cases. However, these two inorganic depressants are toxic and hazardous. Their use could cause heavy pollution problems and a large loss of precious metals. In order to adapt to the requirements of sustainable economic development and environmental protection, the research and development of green and environmental depressant has gained more and more significance."

Jan 1, 2018

By D. Z. Wang

A red copper plate, discovered in the ruins of Dachengshan in Hebei province, was recognized as a forged one rather than a cast one, which means it was probably made from natural copper during the Longshan Culture period (2200~2208 BC) in the Chinese history. The copperware, found in the Niangniang Tai relics in Wuwei city, Gansu province, contains 99.6% copper and 0.4% Sn, Pb, Sb and Ni, which was guessed to be made during the Qijia Culture about 2000~ 1900 BC in the Chinese history in the late Neolithic before Shang dynasty. This shows that Chinese ancestors were able to distinguish, sort and use some native metals and minerals more than 4000 years ago.

Jan 1, 2014

By S. K. Pan

The process flow-sheet adopted in treating hematite iron ore in India through wet circuit generates not only 15-25% slime of Run-of-Mine (ROM), but also results in loss of very high quality fine iron ore particles along with it. As the reserves of hematite iron ore is depleting, it is necessary to explore the possibility of upgrading other types of low grade iron ore and slime for recovery of iron minerals; extensive research in this field is being carried out. While beneficiation of low grade ore is yet to be established, slime beneficiation has been quite successful and many installations of slime treatment plant are underway. In SAIL mines, the slime is mainly the discarded particles from Classifiers, which are less than 0.2 mm sizes. R& D initiative has been focussed on the beneficiation of the slimes (49-60% Fe, 3-10% Al2O3 & 4-10% SiO2) of Dalli mines to generate concentrates assaying 62-64% Fe, 2-3% Al2O3, 3-4% SiO2 and a few innovative facilities for the same has been introduced at this mines of Bhilai Steel Plant (BSP). At Dalli mines, the slime is of very poor quality. A typical slime analysis assays 48.54% Fe, 15.1% SiO2, 8.5% Al2O3 and consists nearly 60% (by wt.) particles less than 38 micron. Slime analysis revealed substantial quantity of very high density mineral particles, those causes jamming of Thickener due to faster settling. A novel technique has been implemented to classify the concentrate ore particles from the gangue mineral particles by processing through Fluidized Bed Classifier (FBC) system, which is a gravity concentrator, to treat 50% of the slime generated and the rest is treated through de-sliming hydro-cyclone followed by Medium Intensity Magnetic Separator (MIMS). A special self-vibrating launder has been designed and introduced into the system to recover tiny iron ore particles, which could not get captured by the permanent Neodymium rare earth magnet in MIMS. The classified iron mineral particles from FBC are further treated in a battery of hydro-cyclones followed by modified Slow Speed Spiral Classifier (SSSC) unit. Multiple feed entry system to the SSSC unit is unique and use of particular feed entry point depends on the desired quality of the product and thus converted to a beneficiation equipment rather than mere de-watering unit. By processing slime in FBC system, the valuable iron ore particles with 62.5% Fe, 5.2% SiO2, 2.23% Al2O3 has been recovered from the slime at a material yield of 30%. And very high valued concentrate particles with more than 65% Fe has been sorted out through the magnetic separation route. The overall extra production of beneficiated slime concentrate is 40-45 tph with 63-64% Fe from a slime feed of 120-130 tph solid. This paper outlines few new approaches in iron ore slime beneficiation at Dalli mines for maximum recovery of valuable minerals. Keywords: fluidized bed classifier (fbc), iron ore slime of dalli mines, medium intensity magnetic separator, slow speed spiral classifier (sssc)

Sep 1, 2012

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By M. L. Liu

This work reports the results about the determination of mean activity coefficients and relative partial molar free energies for copper sulfide mineral bioleaching solutions by potentiometric method at 25ºC. The experimental potentiometric data were obtained by combining a solid state membrane-cupric ion selective electrode (Cu2+ ISE), containing a KNO3 filling solution, and an Ag/AgCl electrode. The measurements were performed in different series of copper sulfide mineral bioleaching solutions. The non-ideal behavior of the system was described on the base of the Pitzer ion-interaction model for mixed salts. Meanwhile, the relative partial molar free energies of bioleaching solution were investigated. The determination of the thermodynamic properties offers a basic data for the study of copper sulfide mineral bioleaching solutions.

Jan 1, 2014

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

The energy dispersion X-ray fluorescence (EDXRF) analysis technique is a rapid and accurate method for describing sample?s element component and percentage composition. On the base of profound research for the national and international development and research condition, the author researched the EDXRF analyze technique and the EDXRF analyzer?s principle in depth, the difficulties and the key points for research and development of EDXRF analyzer; gave a scheme for re-search of bench EDXRF analyzer; researched some algorithms used in energy spectrum analysis; developed the energy spectrum analysis software based on the Visual C++ 6.0; together with the energy spectrum analysis software, the author designed and processed the structural of the bench XRF analyzer and integrated the import X-ray tube, thermoelectrically cooled Si-PIN photodiode X-ray detector and pulse amplitude analyzer as a model machine. The result shows: The model machine can be used in multi-element analysis at the same time for different types of dry mineral samples, with fast analysis speed, accurate model and high stability.

Jan 1, 2014

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By Hermann Wotruba, Günther Petzold, Fabian Riedel

"Increased mechanisation in underground stoping operations results in higher waste percentages in the run of mine. A new method of reducing waste is optical sorting. Optical sorters have low maintenance costs and can be installed underground. Rejected waste can be backfilled directly without having to be hoisted, therefore increasing the shaft capacity for a more valuable product.Pre-Concentration by Optical SortingA series of tests with an optical sorter at the laboratories of the Mineral Processing Department of the RWTH Aachen have shown that it is technically possible to sort almost any kind of ROM which has even slight differences in colour (Platinum Reef, Gold Reef, Kimberlites, Industrial Minerals, Aggregates, Coal, etc.).By employing optical sorters prior to conventional sorting plants, it is possible to reduce the amount of waste to be processed. Figure one shows test results of ore which is quite similar in colour to the waste (grey). With increasing waste in the feed, the recovery decreases according to the graph. In figure two, the colour ratio parameter of the sorter was changed with a similar waste percentage in the feed. With increasing loss of ore, a cleaner product can be achieved. Before designing a sorting plant, throughput tests are carried out. Throughputs vary depending on the size range. Sorters have a limit of about 250mm top size. In this upper size range, throughputs of 150t/h can be achieved."

Jan 1, 2003

By O. A. Bascur

It is difficult to analyse the economics without an integrated view of mine transactions, stockpile inventories, process flows and assays. The lack of integration of mining and metallurgical information with sufficient detail to analyse and act is a problem. However, to take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods use process models to identify inconsistent information in the case of corrupt actionable information. This paper presents new strategies that transform the data into business information for continuous improvement and optimization. This technical presentation will review recent implementations enabling large metallurgical complexes to improve their data quality for overall production and energy management. A competence center emerges as an enabler for implementing operational intelligence. The evolution of Web services to troubleshoot plant information and to collaborate at the enterprise level is presented.

Jan 1, 2014

By A. Tolentino, J. Bravo, M. A. Corona-Arroyo, C. Quintero, R. Zarate, A. Lynch, L. Carillo

"This paper presents the performance of the flotation circuit of Minera Fresnillo PLC, Mexico. A plant survey was carried out on the lead banks and a size-by-size assay on the samples was conducted. The results indicate that the plant is treating fine particles in the flotation circuit. At least 30% of the particles in the feed are finer than 8 microns and that high amounts of Pb, Au, Ag and insolubles are in this particle size. It was also found that higher percentage of insolubles in the -8 micron particles are recovered in the final concentrate rather than being rejected in the tails. The presence of high amounts of insolubles in the concentrate is an issue of the company. The result of the plant survey provided valuable information for effective reduction of the insolubles in the concentrate and for plant optimization. The work conducted is part of the training of the students involved in a mine placement in the Alban Lynch Student Venture. INTRODUCTION Minera Fresnillo is one of the operating mines and the main contributor to the silver production of Fresnillo PLC group, the world’s leading producer of silver from ore. It is located in the mining district of Zacatecaz, Mexico, approximately 650 kilometers from Mexico City. The major minerals that make up the ore are galena, sphalerite, tetrahedrite, pyrargyrite, proustite, polybasite, pyrite and pyrrhotite. Minera Fresnillo has a capacity to treat 8300 tonnes of ore per day. The plant consists of semi-autogenous mill - ball mill – hydrocyclone circuit for primary grinding followed by silver-lead flotation then zinc flotation circuits. This paper reports the plant audit conducted in the silver-lead flotation circuit (Figure 1) of Minera Fresnillo. The circuit includes rougher, scavenger and two stages of cleaning. The tails from the scavenger goes to the zinc flotation circuit while the second cleaner yields the final silver-lead concentrate. The feed to the circuit has a particle size of 90% finer than 75 microns and generates a concentrate with grade of about 35% Pb, 5700 g/ton Ag, 16 g/ton Au and recoveries of 90% Pb, 90% Ag, 64% Au, respectively. Although the plant achieves their target concentrate grade and recovery, the concentrate also contains significant amount of insoluble materials which is about 18%. These insoluble materials consist of gangue minerals. The plant audit was conducted primarily to determine the possibility of further reducing the amount of insoluble materials present in the silver-lead concentrate."

Jan 1, 2018