Search Documents

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003

By A. P. Chaves, D. Jose Neto, M. G. Bergerman, E. S. Mano

"More complex ore comminution and concentration operations have found increasing application in the mining industry due to lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. They allow removing a significant mass of material with little or no content of the relevant mineral before the ore is fed into the processing plant, with the consequent reduction in the mass to be processed in downstream operations. Significant benefits arise out of the use of pre-concentration, such as higher contained metal output without the need to increase the grinding or flotation capacity, and longer mine life. The grade of marginal ores could be enhanced to a level that would make their exploration economically feasible, which would result in increasing exploitable reserves. Nevertheless, few studies to date have assessed the resulting impacts on ore grinding energy consumption and wear after the gangue is removed through pre-concentration operations. This study evaluated the energy consumption and wear of grinding circuits in Brazilian mining operations in which the feed has gone through a pre-concentration stage. Such assessment was based on different samples of sulfide and oxide ores. Laboratory tests were carried out to investigate the power consumption and wear of grinding circuits with and without a pre-concentration stage. Laboratory test results were used to simulate industrial grinding circuits based on both alternatives and illustrate the environmental and economic benefits of each one.INTRODUCTION Increasingly complex ore concentration operations in several stages have found broadening application in recent years in view of lower grades and higher complexity of the available ores. An alternative to coping with the higher capital and operating costs of ore processing plants is the use of pre-concentration stages. Different ore processing technologies can be used for that purpose, such as magnetic separation, density segregation, and separation methods based on high-tech sensors (ore sorting). Currently, the most common methods are gravimetric processes, in view of their low cost, particularly jigging and dense medium separation methods, such as the drum and cone separators manufactured by Western Machinery Company, Teska, Drewboy, Norwalt, Dynawhirlpool and Tri-flo, and dense medium cyclones (CAMPOS; LUZ; BRAGA, 2010). The use of dry ore sorters has also grown significantly in recent years (Jose Neto et al. 2017). The selection of the separator type depends essentially on the ore particle size, required flows, and operating density ranges. All these methods may even be used after preferential blasting in mining (Grigg & Delemontex, 2015)."

Jan 1, 2018

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"A gold has been leached with ammonium thiosulfate solution and several leaching conditions have been studied. The leached solution has been recovered by solvent extraction and the optimum conditions have been investigated.SUMMARYIn this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 – 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 – 3.0x103 mol/m3 NH4OH, 0.4 – 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration."

Jan 1, 2003

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

By M. Barsky, E. Barsky

A study was conducted to elucidate the relationship between the hovering velocity and the particle settling velocity. The experiments were carried out in a water medium on five materials ranging in density from 1.070 to 4.000 kg/m3. Analysis of the results with allowance for the distribution of stream velocities over the cross section of the pipe revealed that the final settling velocity of the particles was equal to their local hovering velocity (on the stream axis), and not to the average velocity of vertical flow as is generally believed. It therefore follows that the kinetic structure of the stream must be taken into account when constructing theoretical models of the process for purposes of computation. In addition, the optimal stream velocity is not always equal to the hovering velocity and in fact is governed by other factors as well. Illustration is provided by the results of a study conducted in a vertical cascade classifier comprising eleven identical stages. The feed material was introduced at each stage successively beginning with the topmost (i* = 1 ) and ending with the lowermost (i* = 11). First, the stream velocity that yields optimum separation conditions at each stage of the cascade (i.e. k=50%, k being the yield of a given size class in the fines for a single stage) was sought. Subsequently the conditions of optimal separation for the instrument as a whole were determined (i.e. F(x) = 50%, F(x) being the yield of a given size class for the entire instrument). The results of the study are presented in the table.

Jan 1, 2003

By Jing Zhou

2-hydroxy-3-naphthoy hydroxamic acid code name F203 is a good collector of cassiterite, 1-hydroxy-2-naphthoy hydroxamic acid code name ZJ-3. F203 and ZJ-3 are similar series of isomers. They have similar naphthye, and similar series of functional OH and ?CONHOH, but the seat of OH and ?CONHOH group are different, on the F203 is 2.3; on the ZJ-3 is 1.2, ortho position too. According to Isomeric principle ZJ-3 is a good collector of cassiterite slime too. Using ZJ-3 as collector flotation -10µm occupies 90%, grade 1.16% Sn cassiterite slime of Da Chang Chehe concentration plant, pass one coursing flotation, two cleaning and one scarenging flotation, and obtains grand 18.26% Sn, recovery 92.68% cassiterite concentrate. The result proves the Isomeric principle of flotation reagents is correct again. This principle may supply to synthetize new flotation reagents reference. Keywords: F2O3, ZJ-3, cassiterite flotation, Isomeric principle, Isomeric principle of flotation reagents

Sep 1, 2012

By Kazimierz St. Sztaba

"Mineral processing – the first technological stage of utilization of mineral – has a very long history. In particular, it revealed and reveals the continuous development and perfection of technological operations and process organization, comprising not only new design solutions and exploitation procedures but also, for example, perfected systems of control and automation as well as methods of process description and result evaluation. During the recent decades the attitude to mineral raw materials was clearly changed, both to the primary ones, i.e. minerals, and to the secondary ones, such as side products and waste, formerly considered useless and at present more commonly used. This results both from the appearance and growth of demand for more and more numerous components of mineral raw materials and also from the necessity of protection of natural resources, constituting the integral part of the system of sustained development of society.These circumstances, and especially the requirements concerning gaining some components which cannot be separated by means of “classical” (used for many years) technological processing operations and aiming at increasing the technological procedures, evoked the necessity of using new technological solutions, applying other basic operations, also the ones characteristic so far for other processing technologies, i.e. chemical, biotechnological and others.These development tendencies, in general commonly perceived, allow us to formulate an opinion that the former state of tasks and processes of mineral processing is being transformed into a qualitatively new form. It can be assumed that this process was signaled by a situation in which, due to the growing role of technological operations based on physicochemical phenomena (flotation and others), magnetic and electrical ones, etc., one should have observed that the former term of “mechanical processing” became inadequate for the real content of the notion determining the discussed stage of mineral utilization, so the adjective “mechanical” disappeared in most languages."

Jan 1, 2003

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Italy is one of the major producers of ceramics in the world. Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and “granitic” sands. These rocks contain other minerals, such as quartz, plagioclase and mafic minerals, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse grind size.This paper reports a study conducted on the separation of K-feldspar from quartz, plagioclase and biotite, from a feed of ground granite. The feasibility of the separation using a dynamic dense medium separation system has been investigated, as an alternative to the traditional flotation technique. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency. Tests were conducted on two samples of crushed granite having size distributions of –3 +1 mm and –1 +0.5 mm.Heavy liquid analysis was performed on the two samples. As the rheological properties of the dense medium interact with the separation efficiency, the stability and viscosity of the dense medium were controlled and kept within an appropriate range; which was achieved with the addition of an artificial contaminant (clay) to the dense medium."

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

By Xie Jiyuan, Hu Yuehua, Yang Songrong, Zhu Zhansheng, Qiu Guanzhou

"By the end of 2000, the first bio-oxidation plant in China that designed by ENFI come successfully into commercial operation in Yantai Gold Smeltery. Its capacity is 50t/d of refractory gold ore concentrate. After the extension, the capacity of bio-oxidation plant reached 80t/d of refractory gold ore concentrate at end of 2001.The refractory gold ore concentrate treated is from different gold mines. After proportionate feeding, the feed typically consists of Au (52.7g/t), S (24.42%), As (3.58%).The bacterial culture used in the bio-oxidation circuit is taken from a mine in south of China, and has been grown over 20 years on a variety of sulfide concentrates in a laboratory of mineral processing, and has shown to be adaptive to growth in a high concentrations of arsenic. It is a mixture of mesophilic microorganisms. The nutrients used in the bio-oxidation process are (NH4)2SO4, KH2PO4, KOH.Before feeding to bio-oxidation circuit, the concentrate would be milled to minus 43µm. The biooxidation product is fed to solid/liquid separation system that consists of a thickener and two press filters, solid from the system is fed to CCD circuit, liquid from the system is fed to neutralization area. The neutralized product is fed to another solid/liquid separation system, and the solid from the system is disposed of on a wasted quarry pit, the liquid from the system is returned to bio-oxidation circuit for reusing."

Jan 1, 2003

By Wayne I. van Drunick

"Energy balance modeling has recently been shown to be a competent tool in the estimation of SAG mill discharge rheology. Work performed by van Drunick and Moys (2001) validated the ability of an energybalance filter to estimate the slurry density from an operating SAG mill. The importance of rheological data is highlighted by several authors who show the effects on load behaviour and thus mill performance. Energy balance models were developed to account for the dynamic energies in the mill discharge sump. The models then made it possible to infer the mill discharge density. A sampling campaign was performed and the errors from the sump energy balance were within tolerable limits.Since the initial results were published, it has been decided to further develop the modeling techniques in order to focus on balancing the energies around the entire mill. The critical measurements for the energy balance will be the temperatures of all the streams entering and leaving the mill, including energy losses to the environment. Metso’s OCS© (Optimising Control System) currently controls the 3 SAG mills at Anglogold’s Mponeng Gold Plant (South Africa). The OCS has built-in Kalman filtering tools to effectively handle variances and noise in the models and the mill circuit data respectively. The new models are therefore constructed in the OCS platform, and will be run in parallel with Metso’s current modeling and filtering systems. The work is a collaborative effort between Anglogold, the University of the Witwatersrand and Metso. The benefits of energy modeling, compared to mass modeling, are that energy data are more accurately measurable than mass data. The inferred mill parameters can therefore be improved provided that a competent set of models is produced to process the (accurate) thermal measurements."

Jan 1, 2003

By Kauko T. Ingerttilä, Jouko O. Kallioinen, Jaakko O. Leppinen, Alexander V. Lashkul, Vladimir E. Nenno

"Separation in Froth (SIF) is a process for the separation of mineral particles during their descent downwards through a moving froth layer, generated on the surface of water or some other liquid media by means of a bubble generator and frother. Due to the special operation principles of SIF it is possible to separate mineral particles that are about 10 times coarser than the optimal particle size for conventional flotation. In this paper the performance of the SIF technique is presented in the separation of apatite, calcite and silicate minerals from various industrial sources, based on tests with laboratory and pilot plant-scale SIF machines. Basic laboratory test results of the flotation of pure diamonds are also presented.It was shown that calcite, apatite and diamonds with particle size up to about 3 mm can be successfully floated with SIF at high recovery and grade, provided that the degree of liberation is sufficiently high. Coarse calcite (+0.25-2.8 mm) was concentrated with reverse SIF in one flotation step at 87% recovery with better than 99% grade. Apatite particles coarser than 0.2 mm are not well floated in the conventional flotation circuit leading to high P2O5 content in the coarse size fractions of flotation tailings. On the contrary, SIF is capable of recovering such coarse particles at high recovery. However, P2O5 content of the SIF tailings starts to increase at about 0.7 mm due to insufficient liberation of apatite. At higher particle size the lack of hydrophobicity of apatite particles is also likely to lower the recovery.The pilot plant testwork showed that SIF can be successfully used at operating plants not only for preliminary upgrading of the feed of conventional flotation, but also for producing final grade calcite concentrate (>99.5%) from the screen overflow or from the cyclone underflow in a particle size range up to 1 mm. It was particularly promising that the separation took place in one SIF flotation step, instead of several stages of the conventional flotation circuit, with over 90% calcite recovery. The specific capacity determined with the 1 m2 pilot plant unit was approximately 30 t/m2h. Simultaneously the consumption of chemicals was significantly lower than for conventional flotation."

Jan 1, 2003

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003

By A. C. Maffei, M. V. Lins Gonçalves

Ore concentration processes are a function of the respective particle size distribution; however, most of them do not use an efficient operational method to determine it. From a practical point of view, the surface area can be calculated for any size analysis. The physical principles for determining the size distribution in each method are different, for the results will not be compared directly. During the development of the research project of the sulfide ore flotation method using inert gas, different methods for calculating the specific surface area have been used, such as sieving, sedimentation/X-ray, laser diffraction and BET, i.e. specific techniques to determine the specific surface area of copper and gold ore concentrates. The statistical method of minimum squares was used to achieve practical correlation equations among them. Regarding these two ores, if one knows a specific surface area value using one of the methods above, one can predict the result of the others. Diminution of the reagent consumption was so controlled and it could be even decreased by using inert gas.

Jan 1, 2003

By Sarah K. DeBono, Alan J. Monaghan, Emmanuel V. Manlapig, Gregory J. Harbort

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber."

Jan 1, 2003

By D. Whittles, S. Kingman, K. Jackson, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

By Pradip, Beena Rai

A molecular modeling study was carried out on an adsorbed oleate monolayer on the surfaces of three calcium minerals, fluorite, calcite and fluorapatite using Universal Force Field (UFF) potentials. The cleavage plane of calcite {104} was the best template for oleate monolayer adsorbed since the surface structure enabled all the calcium sites available on the surface to be occupied by oleate anions. The area occupied per chain of oleate in this well packed monolayer was computed to be 20.2 Å, which exactly matches the value calculated to be the parking area per oleate molecule for a fully packed monolayer based on strictly geometric calculations. On the other hand, the precentage of calcium sites occupied by oleate to achieve a fully packed monolayer in case of fluroite and and fluorapatite was found to be 67% and 75% respectively. The results of this theoretical study suggest that while all the three adsorption conformations, that is unidentate, bidentate and bridging type are equally likely on fluorite and fluorapatite, bridging is most likely on calcite. Interestingly, all the conformations are observed experimentally for calcite-oleate system also. The reasons for this discrepancy between the theoretical predictions and experimental observations are not clear. More work is required to resolve this discrepancy, in particular simulation studies in presence of solvent water molecules on the surface.

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duval

"The monoalkyl ethers of polyethylene glycols are universal flotation reagents because they can be used as collectors, frothers, surfactants, and depressants. Their collecting power was demonstrated for different minerals including coal and quartz.It was confirmed in this work that monoalkyl ethers of polyethylene glycols could be used as collector in flotation of quartz in a monobubble Hallimond cell. Since feldspar does not float in the same cell, it was also shown that selective separation of quartz and feldspar in the Hallimond tube is possible. However, a trail to use the monoalkyl ethers of polyethylene glycols compounds for separation of quartz and feldspar by flotation of mixture of these minerals in a Mechanobr laboratory flotation machine was futile, indicating that these reagents required special environment for flotation.Most probable parameter responsible for a decrease in quartz flotation in the flotation machine is the hydrodynamics of process, and different adsorption/desorption conditions. To prove this, another series of experiments was carried out to separate quartz and feldspar, in which a laboratory flotation column was utilized. The performance of the flotation column was in between that of in the Hallimond tube and flotation machine. These experiments confirmed that the hydrodynamics of flotation plays a vital role in flotation of quartz with monoalkyl ethers of polyethylene glycol compounds."

Jan 1, 2003