Search Documents

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling."

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or EPD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to – 2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to –2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: –2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals."

Jan 1, 2003

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By John Ralston, Jonas Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Mineral froth flotation is one of the most widely used processes to separate particles of valuable mineral from its associated gangue. It involves the selective separation of the hydrophobic particles from the slurry into the froth. The hydrophobic particles attach to the air bubbles and rise up to the froth phase on top of the slurry. The valuable mineral is collected when the froth overflows the cell wall. The separation performance of the process can be linked to the amount of solids and valuable material loaded on the bubble shells. In addition, it is well known that in most mineral systems, the presence of solids can enhance the stability of the froths. How the solids get to be distributed and what proportion is actually attached and stabilising the bubbles is not well known.This study aims to establish the relationship between operational variables, solids loading on bubbles and flotation performance. For this purpose, a series of industrial experiments to sample the solids in the bubble films under different operational conditions were carried out in two copper concentrators under steady state conditions. Samples of the lamellae were taken by touching the top surface of the bubbles with a glass slide. The amount of solids and liquid per unit area in the bubble lamellae can subsequently be estimated gravimetrically and by image analysis. The grade of the attached particles was also measured by adequate sampling. This gives an indication of the maximum grade that could be achieved from the process under the operating conditions."

Jan 1, 2003

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"Rare Earth water dregs is the drained waste dregs, which contains over 0.2 percent thorium dioxide and about 6-10 percent di-Rare Earth trioxide, which is beyond the standard of draining off that China governments set, so that the Rare Earth water leach dregs must be sacked and laid down in storehouse, which costs lots of money. It is a pity that the RE and thorium compounds very useful elements in industry are discarded. A lot of work must be carried out so that this resource was fully developed.In this paper, four separation techniques of recovery Rare Earth minerals and enrichment thorium element and reduction thorium content of drained dreg for the different test samples of Rare Earth water leach dregs which is radioactive waste dregs got from diverse locus are studied, respectively, and the separation characteristic and the separation process are described, using several combination processes of classification and gravity and flotation separation which were prepared according to the characteristic of test samples and technology. The test results show that the combination processes are the more remarkable separation techniques and the flotation reagents used in test can be applied to utilizing synthetically radioactive waste dregs. Through the combined technique process, three parts of products were obtained, namely, Rare Earth concentrate collected, the thorium product enriched and a large amount of the waste dregs product that can be directly drained and the total quantity is 50%-60%. In order to determine optimum technical condition, the effect factors of separation process were investigated in the test."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By Hamid-Reza Manouchehri

"The triboelectric charge attributes of some silicate minerals (i.e., feldspar, quartz and wollastonite) after contacting different triboecharging medium made of different materials were studied. The charge acquisitions by different size fractions of minerals were monitored and accordingly the energetic work function values, i.e., the main parameter determining the entity of triboelectric charges acquired by mineral grains, of the examined minerals were estimated. Moreover the separation behavior of different size fractions of these minerals through the electric field of a laboratory free-falling separator when the mineral grains are charged by different tribochargers were observed and considered as the electrical separation potential of the examined minerals.Furthermore, the role of adsorption of different chemical species on triboelectric charge characteristics and charge acquisition of mineral samples were described from theoretical point of view and the effects of some chemical reagents on triboelectric charge acquisition of the examined minerals were studied. In addition the separation behavior of chemically conditioned quartz, feldspar and wollastonite minerals, using different anionic and cationic reagents, through the electric field of a free-fall electrostatic separator before and after chemical conditioning were monitored.Finally an attempt was made to translate the findings from single mineral systems to a complex silicate ore, containing mainly of feldspars, quartz, and wollastonite. Different separation tests under various conditions were conducted to this complex silicate ore. Before passing through the separation device, the ore sample was conditioned by different cationic and anionic reagents and then was triboelectricaly charged by different tribocharging medium in order to find the effective reagent and tribocharging medium for separating silicates. Besides the role of temperature and humidity of the surrounding ambient in separation behavior were considered."

Jan 1, 2003

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By Natalie J. Shackleton, Deryck de Vaux, Cyril T. O’Connor, Vratislav Malysiak

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. The objective of the study was to investigate the effect surface passivation and inadvertent activation have on flotation and how this can be managed so as to increase the separation of pentlandite and pyroxene. The aim was to minimise the percentage pyroxene reporting to the concentrate and simultaneously maximise the pentlandite recovery. The testwork incorporates the addition of an activator (copper sulphate), a complexing agent, such as DETA (diethylenetriamine) and a dispersant (polyphosphate) at pH 6 and pH 9 in an attempt to alleviate the surface passivation of pentlandite and inadvertent activation of pyroxene. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion."

Jan 1, 2003

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels."

Jan 1, 2003

By Daniela Venter, Stephen Chryssoulis, Ken Stowe

"A sampling campaign was conducted at Kemess in order to identify and assess the chemical and physical factors, which control free gold flotation kinetics in the rougher and cleaner circuits. The rationale behind this approach was that accurate knowledge of the parameters affecting free gold flotation kinetics, can be used to determine how to accelerate free gold flotation. Collected samples were composites of 5-6 cuts over a four-hour period, at steady plant conditions.In the rougher circuit, coarser equidimensional gold particles floated ahead of the finer grained and the flaky gold. Sulphur followed by molybdenum and to a lesser extent silver enhanced gold flotation kinetics, while hydroxyl followed by carbonate ions induced depression."

Jan 1, 2003

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania).

Jan 1, 2003

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling.INTRODUCTIONThe early 1900?s saw the beginnings of published papers which tackled the problem of what influenced the power draw of tumbling mills and what equations (models) were suitable for predicting power draw. This interest continued for the rest of the 20th century and the literature contains many papers that attempted to satisfactorily answer these questions. A common and disappointing theme in the majority of them, however, is the distinct lack of suitable experimentally derived power draw data. This deficiency consequently limited the practical application of many of the attempts at modelling mill power draw. Prior to the early 1990?s some limited data on the power draw of grinding mills in the literature can be found, but as Harris et al (1985) remarked they are ?... too frequently unusable simply because one or more essential variables have been omitted?. The absence of published results, from vigorous experimental testing of the various models, has resulted in a general lack of evaluation of the validity of assumptions and hypotheses that such models contain. Harris et al (1985) however, did make some efforts in attempting to evaluate the performance of various power prediction equations and in so doing further developed a semi-empirical one of their own. However, in using manufacturers? published data, which themselves were undoubtedly generated by proprietary equations of unproven validity, they probably succeeded in generating little more than a consensus of the various errors in these models."

Jan 1, 2003

By A. Pankewitz

The well-established on-line particle size analyzer OPUS manufactured by Sympatec GmbH, has been successfully implemented in several mining and industrial minerals project. OPUS monitors the particle size distribution in 31 fractions as well as the solid concentration in opaque and highly concentrated ore and mineral slurries on-line in real time e.g. behind mills or cyclones applying 31 ultrasonic frequencies for highest resolution. Ultrasonic extinction overcomes all limitations known from optical and mechanical systems like contamination, blockage and wear. OPUS measures slurries in their original state without any dilution, hence no extensive sampling procedure or sample conditioning is required thus no dilution errors occur. Due to the OPUS design and suitable algorithms entrained air bubbles do not affect the quality of analysis at all. The sensor covers particle size distributions from 0,01 to 3.000,00 µm and solid concentrations up to 70 % by volume and can be easily adapted to a number of production lines simultaneously. Jiangxi Copper?s Dexing Mine is one of the biggest copper mines in Asia and among the first users for OPUS on-line particle size and concentration analysis in mining industry. OPUS is connected to 2 process lines. Jiangxi Copper has implemented OPUS for into their central control system for the grinding & classifying circuit of one SAG mill and one ball mill. Analysis data and process control as well as optimization based on OPUS particle size and concentration measurements will be discussed Keywords: particle size analysis, ultrasonic extinction, concentration analysis, grinding control

Sep 1, 2012

By N. Nehoroshev, P. Solozhenkin, N. Voyloshnikova, A. Pshennikov

"Molecular modeling of clusters of major bismuth minerals, Bi2S3, was carried out whereby molecular models of minerals and reagents clusters were created. Their HOMO and LUMO energy levels were calculated and using known modelling equations, the absolute hardness ?, eV and electronegativity were calculated. The charges of separate atoms of clusters and the change of properties of the minerals were determined which allowed predictions of the flotation properties of raw ores containing rare bismuth minerals. Modeled complexes containing the clusters of minerals and various collectors were constructed, consisting of atoms and bonds within clusters of minerals. Major physical and chemical parameters were determined for the complexes created, including the total and electronic energy. Based on the energy calculations, predictions of the collector efficiency were proposed. The efficiency of collector was established for various thiolic reagents, the compounds of phosphorus (III) and mixtures of reagents. Theoretical results were checked and confirmed against laboratory ore flotation tests. A gold-bismuth-magnetite ore type was studied where gold, bismuth and iron (magnetite) are of industrial interest. The ore contains 2.8 g/t Au, 1.0 g/t Ag, 0.26% Bi, 45% Fe and 1.25% As. Sulphide mineralization can be mainly found in the form of pyrrhotite, pyrite and arsenopyrite. Bismuth can be mainly found in the form of bismuthite and native bismuth. Gold is fine. A flow sheet for Zhelezny Kryazh ore treatment was proposed. This flow sheet consists of grinding to 95-98% -74 µm, sulfide flotation with two cleaner with xanthate addition, cyanidation of flotation concentrate and flotation tailings included treatment with with CaO (6 kg, 6 hours), cyanidation (8 hours) and CIL (8+24 hours). Saleable products are gold doré, bismuth and iron concentrate."

Jan 1, 2014