Search Documents

By Alexander B. Reeb, Richard J. Varuso, George M. Filz, Jehu B. Johnson

"T-walls, which are concrete floodwalls in an inverted “T” shape, are an integral component of the Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS). In order to resist large lateral flood loads, T-walls are typically supported on long batter piles that extend through the weak and compressible clays and peats commonly encountered in southern Louisiana. Since the piles are battered, settlement of the compressible foundation soils can result in loads acting normal to the piles and induce pile bending moments. Therefore, the design of pile-supported T-walls is a complex soil-structure interaction problem that requires detailed and careful numerical analysis to accurately estimate the stresses and bending moments in the piles. For this paper, numerical analyses were performed for three cross sections that each included a two-pile T wall system that was installed within a 15-ft tall new levee embankment. The cross sections were identical except that the elevation of the T-wall base was varied. This paper discusses the analyses, and it compares the influence of settlements and flood loading on the pile stresses and bending moments. In addition, this paper includes general recommendations for the analysis and design of pile-supported T-walls in practice.INTRODUCTION AND BACKGROUNDThe recently completed Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS) includes 350 miles of levees and floodwalls and is designed to defend against a 100-year storm surge event. The floodwalls predominantly consist of I-walls and T-walls. I-walls are comprised of a sheet pile wall curtain capped with a monolithic concrete wall above grade. T-walls are similar to I-walls, but they include a wide concrete base at grade, which forms an inverted “T” shape, and they are generally supported by long batter piles that provide additional lateral and rotational stability for resisting flood loads.During Hurricane Katrina, several I-walls failed, resulting in large breaches and devastating flooding (Duncan et al. 2008, IPET 2009). T-walls on the other hand performed quite well, including T-walls that were overtopped and eroded on the protected side, yet still did not collapse. As part of the HSDRSS, more conservative designs and height restrictions were required for I-walls (USACE 2011), and a number of I-wall sections were replaced with T-walls. However, the design of pile-supported T-walls is complex and requires careful consideration of both flood loading and settlements."

Jan 1, 2017

By B. M. Das

Several laboratory model test results for the determination of the ultimate uplift capacity of single and group metal piles embedded in near-saturated clay have been presented. Based on the uplift test results for single piles, the variation of the adhesion factor with the undrained shear strength of clay has been determined, and an empirical correlation for estimation of the adhesion factor in soft and medium clays has been presented. The group efficiency of piles under uplifting load depends on factors such as embedment ratio, undrained shear strength of clay, the number of piles in a group, and the center-to-center spacing of the piles.

Jan 1, 2010

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Marius B. Wechsler

There are considered deep piles which are fixed in blocks of rotating machinery foundations. A mathematical background is developed for determining the behavior of this kind of piles for motions caused by horizontal and vertical oscillations, as well as by roc-king and twisting. It is assumed that the piles come across a top soil layer of depth c, not capable of lateral support, and penetrate over a length b, in a bottom firm soil layer, or in a bottom soft soil layer in which vibrations can produce voids around the piles. With respect to b and c, as well as to the elastic properties of piles and soils, the analysis leads to the maximum bending moments and shear forces subjecting the piles, to the maximum lateral bearing on the bottom soil layer, as well as to the deflection of the pile and the displacement of the foundation block. The results of the performed analysis can be applied to seismic loads too, and they are illustrated by a numerical example.

Jan 1, 1987

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By F. H. Chen

the Rocky Mountain Region since 1950, drilled pier foundations have been widely used to combat structural movement problems in expansive soils. It is now an accepted practice for engineers to use drilled pier foundations in expansive soil areas. Piers are generally drilled into bedrock in a zone unaffected by moisture change. With some exceptions, such system has successfully prevented damage incurred in the structures as the result of soil expansion. In the last 15 years, no significant advancement has taken place in the design of the drilled pier system on expansive soils. Numerous failures continued to be reported. Causes for the failures were placed on poor drainage, inadequate void under the grade beams or mushrooms on top of the piers. Engineers realize that these are certainly not the major problems. The basic design criteria should be critically reviewed. It is the purpose of this paper to point out the actual problems confronted by designers, the failure module and remedial measures, The writer does not claim to have the solutions. In fact, it will be a long time before real solutions can be found, yet the writer believes the engineering communities, the construction industry and the general public should be aware of the true picture of the problem.

Jan 1, 2010

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By Tracy Brettmann

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2001

By O&apos, M. W. Neill

Mini-piles have been found to be a practical, technically correct remedial underpinning method. They can be constructed in limited access areas with very little disruption. Experience indicated that mini-piles installed using a down-the-hole soil displacement hammer would be particularly effective in the "bottomless" Beaumont Clay formations in the Houston, Texas, U.S.A. area. The University of Houston Foundation Testing Facility was ideally suited to perform tests on mini-piles. The availability of extensive geotechnical data and previous pile test results was invaluable in evaluating the mini-pile test data. As expected, the mini-pile test results were consistant with test results from large sized driven piles in the same soil formation.

Jan 1, 1989

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By Li Tiemin

It is one of important tasks in research of vibratory pile driving to increase speed of pile driving and depth of pile driving -- this means to increase capability of penetrating hard layer. In general, vibratory pile driving hammer make pile be situated in vibratory situation to drive pile by means of weight of hammer and pile, but the depth of pile driving and capability of penetrating layer are limited by dead weight of hammer. This paper introduces a new kind of vibratory pile driving hammer which differs from general ham­mer. A set of pressing system is attached to hammer and pile driving frame. The pull of winch installed on frame passing guide pulleys bring downwards press to pile through absorbing system of hammer. The practice and comparison test have showed that the new hammer is faster in pile driving and bigger in capability of penetrating layer than general one. Now, the vibratory pile driving hammer with pressing device has been applied widely in China. RESUME: The vibratory pile driving hammer based on vibratory principle to design have applied wide­ly in foundation engineering in many countries over the world. In order to suit the needs of deep foundation, at present, how can quicken speed of pile driving and increase depth of pile driving have become even more value to many countries in the world. This paper introduces a kind of rapid vibratory pile driving hammer which can drive pile deeper and more faster comparing with common vibratory pile driving hammer. Therefore, a kind of simple and reliable method has been offered for rapid vibratory pile driving in deep foundation.

Jan 1, 1991

By L. C. Reese

? Good construction and inspection presumed. ? Capacity-computation factors are independent of construction method. ? To account for variable or uncertain site conditions, anticipated construction problems, and/or minimal inspection, increase factor of safety. ? Conduct load tests and/or develop easily implemented design alternates (e.g., straight shaft in case bell can't be formed) to reduce factor of safety.

Jan 1, 1988

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By Alok Bhowmick

The most uncertain and challenging part of a bridge design and construction is the ‘Choice of foundation’. During the planning and conceptual design stage, it is extremely important to choose the right type of foundation. Wrong choice can lead to disaster for the project. This paper will present three interesting case studies of past bridge projects, to demonstrate how correct choice of foundation can help to meet the project commitments while the wrong choice of foundations can led to huge delay in project completion, leading to time and cost overrun.

Nov 1, 2022

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991