Search Documents

By H. R. Shen

Cushion materials are one of the most important links in an efficient piling system. In the past, little has been done in China on this problem, so engineers are still used to those traditional woods, papers and coir ropes. In this paper, the SOA of piling cushions, their testing method and parameters used in wave equation analysis for piling are briefly reviewed. The static and dynamic mechanical characteristics of 3 types of cushion material have been determined in laboratory and suggestions about testing method and evaluation of test results are given.

Jan 1, 2010

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By Arvindh Gupta

BC Hydro proposed to improve the stability of the existing Seven Mile Dam with 54 corrosion protected, re-stressable anchors comprising 92/0.6? strands each, in phase 2 of the program. Being globally the largest capacity anchors ever build, coupled with extra ordinary specifications, the project was a challenge for the entire post tensioning industry. The paper discusses the challenges associated with the anchor material supply as per specifications, extensive research and development carried out by Con-Tech Systems ltd. to overcome the challenges and contribute in making the project a success. The substance of this article is published in the Aug/Sep issue of ADSC magazine.

Jan 1, 2004

By S. L. Karunakaran

There are cases where it is found that a raft foundation would have adequate factor of safety against ultimate bearing capacity failure but the settlements would be excessive. Piles may be introduced in order to limit settlements to an acceptable level. The actual number of piles required to reduce the settlements to an acceptable level may be very small compared to the number of piles required to transmit the whole structure load. The paper focuses on the difficulties encountered in evaluating the load sharing between raft and piles. An elaborate analysis taking into account the interaction between raft, piles and soil is very complex and time consuming. Few approximate methods for arriving at a satisfactory solution to piled raft system are discussed in the present paper.

Jan 1, 1996

By Xuhui

Pile foundations are underground projects which are carried out under complicated site conditions, so it is difficult to summarize their characteristic patterns from the everchanging practical pile foundations. In combination with theories, the paper analyses the effects of sound reinforced concrete piles and various types of defective piles on the propagations of stress waves. Through testing on prototype pile models, by use of the transient dynamic method and comprehensive analysis in both time domain and frequency domain, their reflection characteristics and patterns are acquired. In addition, discussions are carried out in combination with some real projects. Our model tests include comparison of large scale pile models of 20X20cm in cross section, 5. 0m in length respectively in air, standard sand, and natural stratum; prototype model tests of digged piles of 0. 7-1. 2m in diameter, and 18m, 30m in length; prototype model tests of bored piles of 0. 6m, 0. 8m in diameter, 12-20m in length. Test results show that no matter in air or buried in medium, the intrinsic characteristics of sound piles and various types of defective piles are fixed. In their time domain waveforms and spectral diagrams, obvious regularity are shown, which proves that the relations between the pile natures and their dynamic responses are fixed, which provide basis for correct judgement of pile soundness and natures of defective piles.

Jan 1, 1991

By Jeffery L. Ottesen

Early construction delays can jeopardize timely completion of subsequent work. As an early construction activity, and due to many unforeseen issues, deep foundation work inherently bears great potential for impacting the critical path of a planned construction schedule. This article describes two construction projects where delays related to deep foundation work forced the Contractor to consider various schedule recovery alternatives to mitigate those delays. Specifically, deep foundations on Vancouver BC's Millennium SkyTrain light rail extension and on a Mill Facility in the United States are discussed. This article cites examples of permitting delays, alleged design changes, differing subsurface conditions and changed construction methodology, the effect each problem had on the project, the mitigation means implemented by the Contractor to minimize adverse impacts of the problem, and Lessons Learned for each scenario.

Jan 1, 2002

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By Renato P. Cunha

The paper presents the results of a comparative and parametric analysis in which a numerical program developed exclusively for groups of deep foundations under general loading (vertical, horizontal and moment loads) was used. This program, developed in the doctoral thesis work of Zhang (2000), extends the finite layer method to accommodate a simultaneous general loading on top of piled raft foundations, allowing the establishment of a coupled relationship between displacements (in all three directions), rotations (in two directions), and external loads. Zhang (2000) has extensively tested and validated this program against well known case histories, but has not applied it to piled rafts overlying unsaturated tropical soil materials. Hence, this paper further explores the applicability of this program by using it to simulate the behavior of experimental field loading tests carried out at the University of Brasilia (UnB) experimental site. At this site, Cunha and Sales (1998) and Sales (2000) carried out several loading tests on small scale isolated rafts (1 x 1m) and piles (L=5m, dia=0.15m), group of piles (4 piles, raft clear off the ground) and piled rafts (1 and 4 piles underneath a raft in contact with the soil). The authors adopt Zhang's program to backcalculate, hence simulate, this series of experimental field loading tests under vertical loading. They also use this set of results to "calibrate" the program for further parametric analyses. The parametric analyses were carried out with different piled raft configurations in this same soil type, trying to evaluate their field behavior under the effect of distinct (geometric) configurations of pile distribution.

Jan 1, 2002

By Charles R. Conlon, Matthew J. Niermann

This paper presents the underpinning and excavation support systems used for construction at 2100 L Street in Washington, DC. The excavation for the proposed building extended below bedrock, which presented significant challenges for underpinning the historic Stevens School, constructed in the late 1800’s. The Stevens School was underpinned using several techniques consisting of soil mixing below an unreinforced foundation, traditional hand-dug pits to rock, micropiles below rock, and bracket piles. The excavation support system for the remainder of the project consisted of soldier piles and lagging supported laterally by tiebacks and braces. Shotcrete and rock bolts supported the exposed bedrock. This paper will discuss the design, construction and monitoring results.

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

Jan 1, 2017

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

By Gerald Verbeek

There are certain concepts that seem to invite responses from some, including some in the foundation industry and even some within DFI, that are at best surprising. Business owners and their employees share the desire that their company does well and continues to operate. Maybe company growth is not always realistic but maintaining the current level of activity is in the least what they hope for. In other words, they hope that their company is sustainable, and they are fully behind that notion. But when the concept of sustainability is raised, there is, at least with some, suddenly doubt that that is a good thing. And yet, that concept only aims to achieve at a grander scale what the owners and employees desire for their company. There are many definitions of the term sustainability, but probably the most commonly used description is that framed by the United Nations in 1987. It states that sustainability is the concept of meeting the needs of the present without compromising the ability of future generations to meet their own needs. Arguably that definition is too abstract and does not provide the type of specific goals and targets we are used to. To help with that, to some extent, in 2015 the United Nations formulated 17 Sustainable Development Goals (SDGs), to provide "a shared blueprint for peace and prosperity for people and the planet, now and into the future." And undoubtedly those SDGs are fodder for those that question the concept of sustainability in the foundation industry. How can our industry, they wonder, ensure that there is no poverty or hunger (SDG 1 and 2), and the climate action goal (SDG 13) immediately leads to the hot button topic of global warming. And maybe this is where advocates lose (some of) the sceptics of the sustainability concept, but hopefully they will continue to read this article that lays out why sustainability simply makes sense, also for the foundation industry and especially for DFI.

Nov 1, 2022

By K. Oshima

In Japan, earthquakes are experienced frequently. Many buildings and structures in Japan are supported on pile foundations. For these pile foundations, the joint section between the piles and footing (hereinafter referred to as "Pile Head Joint"), where the load of the superstructure is transmitted to the ground through the piles, is important in both the design and construction of works particularly under seismic conditions. This paper discusses the state in which the force is transmitted to the Pile Head Joint, and introduces the basic construction of the Pile Head Joint, based on experimental investigation. Steel pipe piles

Jan 1, 2010

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Emad Farouz, Ehab S. Shatnawi, Charles Winter

The increasing demand for small deformations and high-capacity drilled shafts without enlarging drilled-shaft diameters has motivated the development and increased use of a base grouting (BG) technique. This technique has been demonstrated to improve drilled-shaft axial capacity, especially for shafts tipped into loose cohesionless soils. To date, there are a couple of documented design methods for estimating the axial geotechnical resistance of base-grouted shafts. However, there is no or lack of research that addresses the lateral response of such shafts. A base-grouted drilled shaft test program was carried out during the design phase of the Wisconsin I-94 Zoo Interchange reconstruction project. The test program included installing and testing one base-grouted shaft and one ungrouted shaft under both lateral and axial loading. Based on test results, it was concluded that the lateral behavior of the BG drilled shaft is significantly stiffer than conventional drilled shaft . Hypothetical method was developed to account for potential increased, however, the method should be verified with more lateral load test.

By Ting-Wei Wang, Yung-Wen Chen

Artificial ground freezing is commonly used globally during excavation of shield tunnels and for groundwater control. It is a special construction method for temporary ground improvement that involves introducing coolant into underground pipes to freeze water in the soil. The frozen soil is cemented together as a result to form a frozen wall, which provides high strength and low permeability. Once the thickness of the ice wall reaches design requirements, underground excavation can be conducted with the coolant removed afterward to return the soil to its original state. This technique is cost-effective in scenarios where complete groundwater cut-off and excavation support are required; where work is deep underground and faces difficult ground conditions and where access restrictions limit the use of other displacement-type ground improvement techniques. Due to the demand for shield tunnel construction for utilities in Taiwan, ground freezing has become an important soil stabilization method there. In this article, we will share two brine freezing case studies and an in situ liquid nitrogen experiment that was conducted to develop this technique.

Feb 1, 2022

By Morgan NeSmith

The Port of Palm Beach is a full-service landlord port in Riviera Beach, Florida. The port and its tenants process more than $14 billion in commodities. About 80% of these are exports, which makes the Port of Palm Beach one of only 16 "Export Ports" in the U.S. More than 2.5 million tons of cargo move through the port every year. Ozinga, a fourth-generation family- owned construction materials company, has supplied ready-mix concrete for commercial, residential, public works, landscaping and excavation projects from several of its Florida locations. It planned to build a one-of-a-kind cement storage facility to receive and store international ship- ments of cement for transport to other facilities for the production of ready- mix concrete. Dome Technology, of Idaho Falls, Idaho, designed and constructed the 125 ft (38 m) diameter storage facility. The design and working volume of cement for the facility was just under 27,000 cu ft (765 m3). The design loads required to be supported by the foundation system are shown in this table:

Apr 1, 2023

By George Onorato, Giovanni Bonita

Deep soil mixing (DSM) has now become a ubiquitous ground improvement technique across the globe for producing soil-cementous materials for many types of complex civil and environmental applications. In the field, the cementation bonds of the soil-cement materials are formed under a confining stress conditions; however, these conditions are generally not considered as most wet grab specimens are cured and tested under ambient atmospheric conditions. This has led to an underestimation of the engineering and mechanical properties of the soil-cement mixed material. This paper presents the preliminary findings of the effect of confining stresses on the mechanical properties of soil-cement mixed samples. This paper discusses the specialized field techniques used for modeling confining stresses during curing and presents the preliminary findings from different soil types. The findings indicate a strength increase within samples cured under a confining stress relative to nonconsolidated samples. The magnitude of the strength increase also appears to be different for different soil types. Finer-grained soils appear to exhibit a larger relative strength increase with confining stress relative to predominately granular soils.

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By Ali Bouafia

Five full-scale horizontal loading tests of piles carried out by the LCPC in France are interpreted in order to analyse P-Y load-transfer curves. The experimental piles are either bored or jacked into quite homogenous sandy soils and instrumented by strain gauges for measuring bending moments along the pile. Successive differentiation and integration of bending moment profiles have led to derive respectively lateral soil reaction and displacements then to construct the load-transfer P-Y curves. The initial horizontal lateral reaction modulus was derived from these curves and shows linear variation with depth in accordance with Gibson soils profiles. P-Y curves are validated by back-computation of the pile on the basis de these curves and the horizontal reaction modulus was compared to the recommendations frequently used in pile design practice.

Jan 1, 2002