Search Documents

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC's which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

By W. M. Moon, Hugh G. Miller, C. -S. So

"Digital image processing and enhancement techniques have been applied to airborne gamma ray spectrometry data from Sudbury, Ontario. These results have been correlated and compared with the available geological maps to evaluate their usefulness for identifying lithological units. Digital processing allows the correlation of various data sets, and different combinations of images can be tested and viewed as a composite image. Composite images with pseudocolours provide an opportunity to analyze and correlate information that is not otherwise apparent in individual images. Principal component analysis has been applied to the gamma ray spectrometry data to evaluate their efficacy and relative information contents of the measured and computed data. The results of this study indicate that the combined radioelements image (obtained by combining the radioelement image and the ratio images) is effective for defining areas of relative concentration of a specific element in near surface materials. Furthermore, the composite radioelements image (produced by combining three separate radioelement images) and composite principal components image reflect large-scale lithological variations. IntroductionThe Sudbury area is a unique geological structure located in the southern Canadian Shield (Fig. 1). Because the area hosts economically significant nickel-copper deposits (Pye et al., 1984), it has been surveyed in great detail by geological and geophysical methods. In order to obtain meaningful geological infonnation about the Sudbury area, several studies have been carried out with the application of innovative mathematical techniques for geophysical modelling, and attempts have been made to integrate the multisensor geophysical data available for the area (e.g. Gupta et aI., 1984; Moon et al., 1988; Singh et al., 1993). The main objective of this paper is to apply digital image processing and enhancement techniques to airborne ganuna ray spectrometry data in order to determine their usefulness for regional geological mapping."

Jan 1, 1994

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However, high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives. IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million. Canada is second in world production of asbestos behind the U.S.S.R. The milling of asbestos ore has been done primarily by a series of steps involving crushing, dry-grinding and aspiration using large quantities of air to release the fibres. Contrast this process to those practiced in the purification of virtually every other mineral. Ores other than asbestos are crushed and milled using an aqueous slurry in rod, ball or pebble mills. The finely ground mineral, still as a slurry, undergoes beneficiation by froth flotation, heavy media separation, hydrocyclones or any of the other aqueous techniques currently employed in mineral processing.One of the driving forces behind the use of air instead of water as a means of separating asbestos is the nature of the aqueous asbestos slurry. While most slurries of minerals contain as much as 80070 solids and can still be pumped and transported, asbestos slurries become highly viscous with as little as 10070 solids. These high viscosities reduce the pumpability of the slurry and create severe handling problems. Mills become prohibitively large and uneconomical due to having to handle slurries containing only 10% rock and 90% water.Health-related issues have affected the use of asbestos in many countries. In Canada, the asbestos-producing provinces have introduced stricter occupational legislation to improve safety in the workplace. This primarily means strict control minimizing release of air-borne asbestos fibres . Quebec and Ontario have set limitations of airborne asbestos at 2 (2) and 1(3) fibre per cubic centimetre of air. With present milling technology, maintaining these low levels in the workplace requires constant vigilance."

Jan 1, 1988

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By P. C. Richards

"Future Integrated Gasification Combined Cycle (IGCC) power plants will have superior environmental performance and unmatched efficiency.The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an IGCC plant. SCGP flexibility has been demonstrated for feeds ranging from bituminous coals to lignites and petroleum coke, and the process is ideally suited for combined cycle power generation, resulting in efficiencies of 42% to 46% (LHV).In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology is being built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N. V. Sep). The plant is scheduled to start up in 1993. IntroductionBasic ConceptShell's experience with gasification dates back to the 1950s, when the first Shell Gasification Process was commissioned with oil as feedstock. There are now over 140 SGP gasifiers licensed. The experience gained on oil gasification provided a firm theoretical and practical base for the start of coal gasification process development in 1972.At that time, there were serious concerns about the future availability and price of crude oil. Coal gasification (making carbon monoxide and hydrogen by the partial oxidation of coal) was considered to be an important option for refinery applications, because the synthesis gas (syngas) produced can be used as:• a chemical feedstock for making transportation fuels and chemicals;• a source of hydrogen (making use of the water gas shift reaction) for upgrading petroleum products; and• a fuel for heating process streams and/or generating electricity."

Jan 1, 1994

By R. Ricketts, D. G. Vanderveer, F. Kirby

"A program of mapping, sampling and testing to determine the potential of the aggregate resources throughout Newfoundland and Labrador was commenced in 1978. A 6-km-wide corridor parallel to all transportation routes was selected as the study area.The study consisted of a preliminary surficial interpretation followed by field mapping and sampling. Granular resources were sampled at a 500-m interval and non-granular materials were sampled at a 1.5- to 2-km interval. Data were gathered on landforms and stratigraphy as well as a field description of the sample and deposit types. Particle-size and lithologic analyses of the samples were also conducted.The locations of samples and deposits were mapped on 1:50,000 topographic base maps and summarized for publication at a 1:250,000 scale. Surficial geology maps were produced at a 1:50,000 scale. A computer program is being developed for the search and retrieval of field data.The first phase of the Inventory of Aggregate Resources program is nearing completion and to date has collected information on approximately 9,500 samples throughout Newfoundland and Labrador. This data will be used to provide f or the effective management of these vital non-renewable aggregate resources.The mineral aggregate industry in Newfoundland and Labrador is very competitive, but undercapitalized when compared to other provinces. The demand for aggregates is forecasted to increase to in excess of23 million tons per annum by the year 2002.In terms of over-all mineral production, the extraction of sand, gravel and stone has a significant impact when compared to other minerals in terms of value and tonnage produced.IntroductionThe province of Newfoundland has approximately 18,000 km of coastline. A large proportion of the population lives in coastal communities where, traditionally, beaches have been a major source of construction materials. Beaches have, therefore, often been subjected to overutilization, resulting in erosion of back beach areas or adjacent headlands."

Jan 1, 1982

By S. McCarthy, K. E. Waters, A. Jordens

The beneficiation of rare earth (RE) element bearing minerals has become an active area of research as applications for these elements grow while the supply to non-Chinese consumers is restricted by export quotas. One of the most interesting beneficiation techniques for RE minerals is froth flotation as their unique chemistry suggests that collectors with a specific affinity for RE cations should be able to selectively recover these minerals. Existing literature, focusing mainly on bastnäsite flotation, identifies hydroxamic acids as excellent collectors for RE minerals. The high stability of hydroxamate-RE cation complexes is the explanation most often offered for the observed selectivity of these reagents in bastnäsite flotation however some research has also suggested that mineral solubility plays a crucial role in the success of hydroxamic acid flotation of RE minerals. This work investigates the interaction of allanite, a relatively insoluble RE-silicate mineral, with benzohydroxamic acid using zeta potential measurements and microflotation. The effects of Fe(III) and Fe(II) ions as potential activating ions (cations that form stable hydroxamate complexes) on benzohydroxamic adsorption to the allanite surface are investigated as a potential solution to promote hydroxamic acid adsorption. The results indicate that the optimum conditions for separation of allanite from quartz occur at pH 4 using FeCl2 as an activator for benzohydroxamic acid adsorption.

Jan 1, 2014

By Robert W. Plummer

"This paper describes the use of Geographic Information Systems (GIS) as a tool for mineral exploration by using the Eskay Creek area of northern British Columbia as an example. Data entry, analysis and output are discussed. Examples of some of the capabilities of the technology are presented.The main benefit of the technology is being able to perform complex and sophisticated searches of large and diverse data sets to highlight exploration targets. A GIS is a powerful data management tool that can be used in mineral exploration. It is a computer based system that is designed for the collection, storage and analysis of objects and phenomena where geographic location is an important characteristic. The main function of the GIS is to produce information for the geologist from a variety of sources (geology, geophysics, geochemistry, mineral deposits and so forth) quickly and efficiently. This allows the geologist to examine large amounts of data in a fraction of the time than can be done using conventional manual methods."

Jan 1, 1992

By P. MacPhail, G. S. Dobby, I. M. Flint

"The objective of the laboratory work described in this paper has been to develop a method f or producing small gas bubbles at moderate to high gas rates in a flotation column. Small bubbles are particularly important for attaining reasonable flotation rates of fine particles. An ultrasonic aerosol generator has been employed to add frother solution directly to the gas stream. Using porous glass and filter cloth spargers, aerosol frother addition has produced bubbles at 1/2 to 2/3 the diameter of those produced by conventional frother addition to the liquid, at a lower frother consumption.IntroductionGas bubbles are generated in a flotation column most commonly by forcing gas through a porous medium called a sparger. Typical sparger material includes rubber (pierced with small holes) , fabric (such as filter cloth), fritted glass, or porous metal (steel or bronze) . Solid sparger material is suitable for laboratory use; however, for industrial applications a flexible sparger such as rubber or fabric is necessary to prevent the eventual plugging of orfices with solid particles and/ or precipitates. An exception to this is the use of a gas liquid contactor external to the column in combination with pressure release of gas in water, a method that has been demonstrated to produce very small gas bubbles. The typical objective of bubble generation for flotation column purposes is to produce bubbles with diameter of about 0.1 cm (and less) at a gas superficial velocity of 1 cm/s to 3 cm/s. In general, the smaller the bubble, the better. In man y cases, though, there is little , or nothing, gained by generating bubbles less than about 0.05 ern in diameter.Several factors affect bubble size when generated by a sparger: gas rate, orifice diameter, sparger surface area, surfactant type, surfactant dosage, and static head. At very low gas rates bubble diameter is independent of flow rate and is proportional to orifice diameter. At the moderate gas rates encountered in flotation columns bubble diameter, db' is related to gas flow by: db oc vg n, where vg is superficial gas velocity (rate of gas flow per unit column area). For porous steel and filter cloth, n has a value of about 0.25 for vg between 0.2 cm/s and 2 cm/s(2). The magnitude of the effect of orifice diameter at these gas rates is unclear. The effects of frother type and concentration on bubble size issuing from a single orifice have been measur ed by Miagkovaru , shown here in Figure I(IS). The reduction in bubble diameter upon surfactant addition is due to the lowering of interfacial tension created by adsorption of surfactant at the gas liquid interface."

Jan 1, 1988

By Z. M. Zavodni, C. D. Broadbent

"Major rock slides in open-pit mines are rare, but they can develop in spite of sophisticated slope engineering design practice. Experience has shown that, except under high seismic load conditions, the serious slope instability condition is almost always accompanied by the gradual development of one or more tension cracks behind the slope crest, allowing for time-displacement monitoring. Continuous surface displacement measurements with attendant prompt analyses are usually adequate for the prediction of slope behaviour.This paper describes efforts that have been made to quantify parameters associated with slide movement, and compares the displacement records of several large-scale open-pit porphyry copper mine slope failures. Two principal failure stages are recognized in the typical slope failure leading to total collapse: (a) REGRESSIVE STAGE, during which the failure will re-stabilize if some disturbance external to the rock and structure is removed; and (b) PROGRESSIVE STAGE. during which the failure will gradually displace at an accelerating rate to the point of total collapse unless active control measures are taken. Over-all displacement records in both failure stages are apparently of simple exponential form. with a definite break occurring at the onset-of-failure point.Certain common empirical relationships are suggested for the large-scale slope failures analyzed in this study. Based on plots of displacement rate vs time prior to collapse, a semi quantitative empirical relationship is presented for failure collapse prediction. The comparison of historical slide displacement records furnishes the operating engineer with practical guidelines to estimate the characteristics of future large-scale slope failures."

Jan 1, 1980

By G. Mucsi, J. Faitli, K. Bohács

"The authors developed an online tube rheometer to supplement a Netzsch MiniCer (Netzsch GmbH, Germany) stirred media mill in order to monitor online the rheological characteristics of the suspension and therefore the result of grinding during the process. Previously it was demonstrated that the above measuring system was working appropriately based on the preliminary tests. The product related stress model was applied for the evaluation of the grinding results. It was found that the suspension concentration and the change of the material properties during grinding, consequently the rheology strongly affects the grinding result, i.e. specific surface area, median particle size as well as specific grinding energy. The tested model limestone – water suspensions behaved Newtonian initially, then after a given grinding time their properties had changed and they become Bingham plastic. INTRODUCTIONStirred media milling now is a common practice to produce fine and ultrafine granular materials for different purposes. With an increasing demand of ultrafine powders for industries (Kwade, 1999), wet and dry ultrafine grinding has been increasingly used in various fields, such as minerals (Mucsi, Rácz, & Mádai, 2013)(Rácz, 2014), ceramic materials (Becker & Schwedes, 1999), pigments (Ohenoja, Illikainen, & Niinimäki, 2013), chemical products (Baláž et al., 2013), microorganisms (Kwade & Schwedes, 2002) and pharmaceutics (Afolabi, Akinlabi, & Bilgili, 2014). It is well known that suspension rheology affects the wet comminution of materials (He, Wang, & Forssberg, 2006a). The rheological behaviour of the suspension containing the ground particles might indicate the level of interparticle interaction or aggregation and therefore it is an important variable factor of the process control (Muster & Prestidge, 1995). The influence of the rheological behaviour of mineral suspensions on their grindability has attracted more and more interests and attention, especially on ultrafine grinding performance (He, Wang, & Forssberg, 2006b) (Bernhardt et al., 1999). However, there are still many issues concerning the machine and the process for the different applications. When grinding is effective and the particle size range decreases significantly, the circulating suspension is becoming typically non-Newtonian. The changed rheological behaviour and the increasing rheological material parameters can negatively affect the grinding efficiency; therefore it is an important issue. Ultrafine stirred media milling as well as solid-liquid two phase flow have been studied for a long time at the Institute of Raw Materials Preparation and Environmental Processing of the University of Miskolc. Regarding ultrafine grinding the research is focusing on the description of materials’ grindability (energetic aspects) both in wet and dry circumstances (Mucsi et al., 2013; Rácz, 2014). Concerning rheology, the three measuring pipes tube rheometer was developed decades ago (Faitli & Gombköto, 2015). So far many different solid materials from all over the world had been tested in this rheometer (Faitli & Gombköto, 2015). Main aim of these tests was to gain basic data for large scale hydraulic transport applications. Among the many stirred media mills there is a Netzsch MiniCer mill at the Institute. It was reasonable to combine the two fields together, and the goal of the research presented in this paper is to develop an online tube rheometer for the Netzsch mill and to carry out grinding and rheological testing simultaneously."

Jan 1, 2016

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments.A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including reasonable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects."

Jan 1, 1990

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By R. G. L. McCready, R. O. van Everdingen, M. Kalin, R. van Everdingen

"This paper is based on data generated between October, 1986 and October, 1989, during the implementation of an Ecological Engineering close-out for a zinc mine in Northern Ontario, where 690000 tonnes of tailings contain 41.1% pyrite and 4.1% pyrrhotite. The objective was to determine rates of sulphide oxidation and iron precipitation in the tailings. Those rates are relevant for the assessment of the long-term effectiveness of biological systems employed in the removal of heavy metals from contaminated drainage issuing from tailings.Data were collected on the topography and stratigraphy of the tailings basin, subsurface temperatures and groundwater levels, and chemical analyses were made of water samples collected from a number of piezometers. The thickness of unsaturated tailings varied widely between individual piezometer locations; annual maxima ranged from 0.67 m to 3.55 m, and annual minima from 0 to 2.68 m. Sulphate concentrations ranged from 36 mg/L to 20180 mg/L; iron concentrations from 0.36 mg/L to 9938 mg/L; and zinc concentrations from 0.33 mg/L to 1123 mg/L.The geochemistry of the piezometer samples suggests that some of the initial Fe content, resulting from metal sulphide oxidation, is subsequently precipitated in the tailings pile and, possibly, in the underlying unconsolidated sediments, probably in the form of iron-hydroxide and Na-jarosite. Other metals such as Zn may be co-precipitated with Fe. The discharge of a portion of these metals to the environment would be delayed by this process. Some of the initial sulphate may also be lost from solution, probably by precipitation of gypsum; approximate saturation degrees for gypsum ranged from -3.27 to +0.47. The precipitated minerals will somewhat decrease the porosity and permeability of the tailings.Sulphide-oxidation rates, calculated using the analytical results and the estimated amount of annual recharge at the tailings site, average 0.0057 mol/kg/yr. Calculated iron-precipitation rates average 0.000386 mol/kg/yr. It is concluded that the characteristics of seepage from mining wastes may change with time, reflecting the solubilization of precipitated secondary minerals."

Jan 1, 1992

By Gerhard Heinrich

"The composition and the possible utilization of a slag sample from a nickel smelter operation in the Sudbury district were investigated. The sample containing 0.136% Ni, 0.10% Co and 0.29% Cu could be characterized as a fayalit e slag with a sulphide bearing glass matrix. While the fayalite contains most of the Co, Ni is enriched within both sulphides and fayalite. Cu is only present in higher amounts in sulphides or metallic droplets. This, as well as the small grain sizes of the mineral phases, inhibits significant enrichment by mechanical methods. However preconcentration is possible by means of magnetic separation. An effective hydro metallurgical approach proved to be oxygen pressure leaching with sulphuric acid. Accordingly, the method proposed for processing the investigated slags is to combine the normal utilization as coarse construction material with pressure leaching of the fines and the ground upgraded magnetic fraction. Besides the recovery of base metals, the leaching process yields fine-grained residues, which, after addition of CaD, will set to a cement-like material, or can be used as a pozzolanic cement colour. INTRODUCTIONDuring the pyro metallurgical processing of nickel ores, the valuable metals nickel, cobalt and copper are enriched within the sulphide matte, similar to the smelting of copper ores. The resulting waste materials are slags, which may still contain valuable metal contents of up to 0.5% or above . These contents are close to the cut-off grades of some nickel-cop per-cobalt deposits. The methods that are used to recover copper from slags comprise in general further pyro metallurgical treatment, often after enrichment by flotation. Another area of application for such slags is their use as construction material. However, this might cause environmental problems if nickel containing dusts are produced.Based on one example, the characerization and a possible way of complete utilization of nickel smelter slag s as construction materials in combination with partial base metal recovery are described in this paper. The investigated slag sample was obtained from a dump site in the Sudbury district, Ontario. Detailed test series for process optimization were not possible during this study due to the limited available sample size."

Jan 1, 1989

By B. Morrison

"The Kiruna Electric System is a recently developed inclined ore haul age system for underground mining operations. Although an initial investigation was carried out at the Swedish underground iron ore mine LKAB almost three decades ago, it was not until 1981 that the resources of LKAB, ASEA and Kiruna Truck AB were combined to investigate, and subsequently develop an ""all- electric truck"" for the mining industry.It has long been appreciated, that major economical advantages could be realized by a mining operation through an extension of the cost-effective life of the existing ore hoisting system by the use of ramps to haul ore up to the main haulage level. Diesel truck s have been used and are being used for ramp haulage. Their use however, is limited due to ventilation and operating costs restraints.There are numerous instances of orebodies, located within a couple of hundred metre s of surface, or below an existing hoisting facility, being developed by ramp access while the shaft is being sunk. Development of an orebody via ramp access has many advantages to a mining operation where mechanized mining is to be practiced. These advantages are both practical and economical; generally falling within the over-all umbrella of the phrase ""cash flow"" mining.The decision to sink a shaft is a major committment by any mining company, regardless of size and financial reserves. Extensive diamond drilling, both shallow and deep must be carried out before a decision can be executed. This constitutes a major financial expenditure over an extended period of time.The decision to sink a shaft must be weighed against the reliability of geological interpretation of the deep diamond drilling results, the stability of the mineral market and potential fluctuation in ore prices and interest rates."

Jan 1, 1989