Search Documents

By A. J. Harrison

"The introduction of an amendment to the Mines Regulation Act in the Province of British Columbia, passed in July 1974, and similar amendments since enacted by other provinces introduced the Canadian underground mining industry to the use of fire-resistant hydraulic fluids.Few, if any, of the hydraulic circuits in use in underground mining at that time were specifically designed for use with fire-resistant fluids, compared with the increasing number of such circuits conceived and in production today. The technology required in designing equipment for use with fire-resistant fluids may be likened to that associated with conventional mineral oils, but, in many respects, a variety of additional and / or alternative considerations must be taken into account. The fast-increasing use and development of fire-resistant fluids throughout all facets of industry, world wide, during the past 20 years has led to a whole new technology in system construction and component design, whereby acceptable performance can be achieved . However , the transition from conventional mineral hydraulic oils has not been without its problems, particularly when retro-fit of existing units was involved."

Jan 1, 1981

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By A. Vasenev

The quality and durability of asphalted roads strongly depends on the final step in the road construction process; the profiling and compaction of the fresh spread asphalt. During compaction machine operators continuously make decisions on how to proceed with the compaction accounting for project specific aspects as: ambient conditions, road geometry, roller type, asphalt mixture characteristics and behavior of other machines. In discussions over quality improvement in road construction it is often suggested to robotize rollers. To operate such robots would of course require operational strategies and routines. The reality of this moment is that these operational strategies and routines are not documented. To identify the existing best working practices and, ultimately, to proceed with developing automated robotized compactors, the knowledge of machine operators should at first be explored and described in a formalized way. Unfortunately operators have difficulty verbalizing their expertise. Observation of behavior, as machine movement patterns, could be helpful to extract the operational strategies, but such observations are time and labor consuming. To overcome this burden we developed a Virtual Reality (VR) environment. In this VR environment operators perform compaction virtually, and their operational choices are traced and analysed. This paper describes this VR development and explains how it helps in following machine operators and extracting their (tacit) professional knowledge. The road geometry and the working conditions are visually represented; the operators show - rather than explain - how they would proceed with the compaction process in the given conditions. Movements of virtual machines are documented, analysed, visualised and discussed. This VR approach is expected to contribute to learning, to more formal description of operational strategies; stepping stones towards compaction algorithms for roller robotisation.

Aug 1, 2013

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By W. G. Deeks

CANADIANS are world leaders in marketing metal and mineral products. Noranda Sales Corporation Ltd. is an international metal and mineral product marketing company operating from Toronto and London, England, where it operates a wholly owned sales subsidiary and is a 50% partner in Rudolf Wolff and Company Ltd., a charter member and the largest metal broker on the London Metal Exchange. Noranda Sales employs 97 people, of whom 52 are university trained and professionally competent in international resource product marketing. We market for 19 companies or divisions in the Noranda Group and 39 companies for whom we act as agent, consultant and purchaser of resource production. Our business in 1976 was 1.5 billion dollars carried out in 45 countries and covering 24 products and materials. Today, ownership of most of the mining industry in Canada has transferred back to Canadians, and this is said with the knowledge that a significant part of the Canadian industry has been Canadian owned and managed from its very early days. Noranda Mines Limited is such an example. It was born in 1922 as the result of a copper-gold showing at Noranda, Quebec, discovered by Ed Horne, a prospector, financed with a grubstake by a syndicate mainly composed of New York businessmen. Shortly after the discovery, when the shares of the company had risen, the syndicate was sold to Canadian interests and, since that time, Noranda has been dominantly Canadian owned and certainly Canadian managed. Today, over 90% of Noranda's shareholders are Canadian, who hold an equivalent percentage of the stock.

Jan 1, 1977

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By John H. McKillop

Industrial minerals production in Newfoundland in--creased in gross value by a total of 175 per cent during the ten-year period from 1954 to 1964. The Province accounts for all of ?Canada's fluorspar production and contains one of the most important fluorspar districts in North America. It is also the only producer of pyrophyllite in Canada, and quite recently has become an important producer of asbestos fibre. Limestone, gypsum, brick shale, sand and gravel also ?Contribute appreciably to the expanding industrial minerals phase of the Province's rapidly growing mining industry. Geological diversity characterizes Newfoundland's industrial minerals: Pyrophyllite deposits were formed by contact metamorphism of predominantly volcanic Proterozoic rocks. Fluorspar deposits are fissure-filling veins having the characteristics of typical epithermal deposits. Chrysotile asbestos production comes from one of the Island's serpentinized ultrabasic belts. Limestone is produced at three localities; two of them in the extensive carbonate rocks of the west coast. Gypsum production comes from a thick evaporite (gypsum and anhydrite) sequence in the Carboniferous rocks of the St. George's Bay area. Introduction

Jan 1, 1965

By Roger C. Parsons

"The problems presented by ice formation and interference with processes, structures and mechanical operations in the mining industry can be expected to increase sharply as more of our mineraI needs are supplied from the far north. A process of rapid ice destruction is presented which lends itself to the effective removal or penetration of ice. Suggestions are offered for applying the system to problems related to mining activity in cold environments. The system can be readily adapted to large-scale operation, the reactant components being transported in crystalline form and volatilized on site.IntroductionThe number of operational mines in northern environments, relative to the number of mines in the temperate zone, will increase in the years ahead. This is not surprising, because:(a) in the past, those mines closest to centres of commerce had minimum transport charges and hence were more economic to develop;(b) great centres of commerce were far removed from northern environments;(c) the exhaustion of ores and lowering of grades in temperate zones now offset to some degree the extra transport costs applied to northern ores;(d) the abundance of excess energy in the north in the form of oil, gas and hydropower attracts mining as a means to justify its development; (e) assuming that the frequency of mineral occurrence north of the 52° N latitude is no different than south of it, there are many deposits waiting to be developed.As a result of current and projected activity in northern environments, we are faced today, and will be increasingly so in the future, with mining problems rarely encountered before-problems related to below-freezing temperatures. Engineering activity in permafrost regions will increase as new mining ventures are developed north of the 52° N latitude, roughly coinciding with the -1.1 ° C isotherm in Labrador, the upper temperature boundary for permafrost."

Jan 1, 1982

By K. Adham

Iron chloride pyrohydrolysis (ICP) is used as an efficient way to fix iron as an oxide, for sale as a by-product or for safe disposal. Iron chloride is reacted with water at elevated temperatures to yield iron oxide and hydrogen chloride. Both the steel industry and synthetic rutile producers make extensive use of ICP. Two technologies are available for ICP: fluidized bed (FB) and spray roaster (SR). Both technologies are energy intensive. Here, fluid beds and spray roasters are compared with respect to their fuel and electrical energy consumptions. Roaster size and oxide product characteristics are also considered. Process models are prepared, using the METSIM® software, and specific energy consumptions are compared. The results will help the industry decide which technology best suits its goals and at what energy cost.

Jan 1, 2006

By Nural Kuyucak, Bohumil Volesky

"Extensive screening revealed a seaweed (alga) biomass type which in its non-living state possesses a very high cobalt sequestering capacity comparable to that of activated carbon and the ion-exchange resin currently used in the cobalt production process. Performance of the new bio-sorbent material was studied by examining its equilibrium metal uptake isotherms generated under different solution conditions such as initial cobalt concentration pH, temperature, and the presence of selected cations and anions. The rate of cobalt uptake was determined, which is a crucial parameter for recovery process design. Almost all cobalt sorbed can also be desorbed with a solution of CaCI2. The bio-sorbent material can be used repeatedly in the sorption-desorption cobalt concentration process. IntroductionIt has been well documented that certain types of microbial biomass, living or non-living, possess a high potential to sequester and accumulate inorganic ions present in aqueous solutions. Metal concentration by microbial biomass from a solution is termed bio-sorption. This phenomenon is quite complex and includes adsorption of metals onto the surface of a microorganism and/or into the cellular structure in combination with ion-exchange, complexation, and/or micro-precipitation. Bio-sorption is generally considered to be a rapid physical/chemical process. The cell wall structure is porous and allows metal ions, as well as large organic nutrient molecules, to pass freely through. Polysaccharides of the cell wall could provide binding amino, carboxyl, phosphate and sulphate groups. In addition to these functional binding groups, polysaccharides often have ion-exchange properties. Sometimes, bivalent cations, such as Ca2+ or Mg2+, help the formation of ionic bond bridges between the negatively charged cell surfaces and positively charged cations in the solution, Proteins in the cell wall could offer functional groups and also offer peptide bonds to bind ions. Interactions between metal and the cell wall components are responsible for the sequestering of metals by way of bio-sorption. Many metals feature a complex solution chemistry and it is not always possible to determine what ionic species are actually present in the solution. The equilibria involved are dependent on pH, concentration, the anions present and other factors. The transport system for the ions are sometimes dependent on both temperature and energy. Biosorbent material could also be regenerated for multiple reuse."

Jan 1, 1988

By Derek Harvey

"The paper briefly describes the development of the Eickhoff ESA60 roadcutter which is based on the old and well used principles of the shearer loader. It is intended to show that the machine offers a viable alternative to the normal methods used for driving roadways and also for coal production . References are made to installations currently operating in Europe with applications ranging from roadway drivage to pillar recovery. The paper also looks at possible applications in Canada.IntroductionThis paper is an attempt to show how the principles used in mechanical cutting, conveying and roof support are being applied to a development system capable of catering to a variety of situations and conditions. It is also intended to illustrate how the same system can be used as a total mining system for the mining of many minerals.In order to give some sort of time perspective to the age of the principles, reference can be made to an article in Coal Mining & Processing which states:- During World War II the Germans developed the "" panzer"" or armoured face conveyor.- After the war the English developed power cutters or trepanners that were mounted on the face conveyor, this then developed into the shearer.- The first shearer was produced by the Anderson Company in England in 1950 and shortly after that the Eickhoff Company started manufacturing shearers in German y.- The first hydraulic roof support was produced in 1954 by Gullick.This is a potted history of the three major components of the new system, i.e.:- Mechanical cutting element based on the shearer.- Transport element based on the panzer.- Optional roof support based on the hydraulic face supports.It can therefore be said that since the "" youngest"" of the elements was produced in 1954 the principles of the system in respect of the rapid change in mining equipment are in fact old.Of the three major components the most important is the cutting element since the major benefits of the system are to be obtained from this."

Jan 1, 1985

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By Kevin Ross

Feasibility Study Team Processing / Engineering?Hatch, Vancouver Mining / Reserves?Australian Mine Consultants, Brisbane Geology / Resources?Roscoe Postle Associates, Vancouver Environmental / Permitting?Rescan, Vancouver Tailings BGC, Kamloops Probable Mine Components Mining tending towards caving methods Underground mine accessed by shaft /conveyor & decline Processing plant producing copper concentrate containing gold Concentrate trucked to rail head for export Non saturated tailings disposal

May 1, 2006

By D. Saramak, Z. Naziemiec

"Chalcedonite is an unique rock due to the relatively small area of its occurrence. It also possesses multi-raw-material features therefore it should be given a special protection aiming at its complete and optimal utilization. It is the natural sedimentary rock and the only mine in Poland, located in Inowlodz, where the opencast mining from “Teofilow” deposit is carried out.Chalcedonite mainly consists of cryptocrystalline and microcrystalline chalcedony together with small amounts of autogenous and detrital quartz. The chalcedony itself is a fairy common mineral and many forms of its occurrence is known, some of them are semi-precious minerals. Among the most popular ones following can be found: agate, bloodstone, onyx, carnelian, chrysoprase. Many countries own chalcedony deposits: Australia, Brazil, India, Canada, Namibia Russia, South Africa. However chalcedony in its pure form does not occur in the mentioned chalcedonite rock. The pores, which take usually from 5% to 25% of volume and have sizes smaller than 0.5 mm, are the characteristic feature of all chalcedonite forms. The paper presents some crucial problems of its processing together with most significant directions of its applications. New method of chalcedonite enrichment based on densimetric separation (patented in Poland) is presented. Results of investigation show that the obtained products can increase quality of concrete and filter grits."

Jan 1, 2016

By D. Hamilton

The electrode of a PEM fuel cell consists of two distinct sections - the catalyst layer and the porous transport layer (PTL). There are several kinds of PTL material, although all use carbon fibres as the solid fraction. The fibres can be matted to form a paper, woven into a cloth, or chopped to form a felt. Despite the different morphologies of the media, they are all anisotropic in structure, that is the majority of continuous fibres lie perpendicular to the direction of bulk transport. Currently, no models account for anisotropy and all transport coefficients are calculated as volume weighted averages or from empirical correlations (not developed for fibrous porous media). The present work presents a new methodology for determining anisotropic transport coefficients in fibrous porous media. A numerical experimentation process is employed wherein random samples of the PTL are generated and used to solve a diffusion transport equation. Effective transport coefficients are determined by integration of flux across the domain boundaries once a steady state solution has been reached. Multiple random samples at each porosity are generated in order to predict statistical variance. The results are correlated for ease of implementation in full PEM models.

Jan 1, 2005

By Yuhua Wang, Wei Sun, Dongfang Lu, Yuehua Hu, Tao Jiang

"With the continuous depletion of high-grade tungsten ores, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and use of toxic collectors.The aim of this study was to develop an environment-friendly processing flowsheet, which was used for beneficiation of low-grade tungsten ore containing 0.45% WO3 from New Brunswick in Canada, and the content of arsenic is 0.68% in this materials. The objective of beneficiation studied was to obtain a concentration containing 60% WO3 with less than 0.5% of arsenic under the condition without any flotation reagents. In this environment-friendly processing flowsheet, magnetic separation technology, classification and gravity separation technology were combined and employed. Firstly, magnetic separation was employed for the first pre-concentration process, over 95% of the feed was rejected as the final tailings, meanwhile, over 85% of arsenic minerals were removed with tailings. Secondly, gravity separation tests were employed on the classified magnetic pre-concentrate in the second pre-concentration process, a second pre-concentrate with WO3 grade of 54.32% and As grade of 5.41% was obtained. Finally, two stage magnetic cleaning were conducted on the second pre-concentrate for upgrading the second pre-concentrate, the mostly arsenic and gangues were removed from the second pre-concentrate. Finally, this novel processing achieved an effective recovery of fine wolframite from low grade tungsten ore with high arsenic. A concentrate with WO3 grade of 64.81% were obtained in new opened processing flowsheet, and As grade was less than of 0.5% in this concentrate. Furthermore, remarkable feature of this processing flowsheet is environment-friendly due to avoid using the toxic flotation reagents during the whole mineral processing.INTRODUCTIONTungsten is an essential metal and is the most widely used in industrial production such as national defense, electro-mechanical products, textile and leather sectors (Srivastava et al., 2000). Wolframite and scheelite are the main mineral sources of tungsten metal. With the continuous depletion of high-grade tungsten ores and the increasing demand for tungsten alloy, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and heavy use of toxic collectors."

Jan 1, 2016

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By Yan Jie

The oxygen-enriched bottom-blowing continuous converting process for copper matte was recently developed by the China-ENFI Engineering Corporation. The first commercial plant based on this technology was successfully commissioned at the Yuguang smelter in China in March 2014. The present paper describes this new continuous converting process and compares technical characteristics with other continuous converting processes including: Kennecott-Outokumpu flash converting, the Mitsubishi Process, the Noranda Converter and TSL continuous converting. The bottom-blowing oxygenated continuous converter with competitive capex and opex costs is seen as an attractive alternative to the Peirce-Smith converter.

Jan 1, 2014

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

By R. De Ruiter

"In times when mines are emphasizing cost reductions, a properly rebuilt shall conveyance can be more cost-effective than building a new unit. Awareness of the safety aspects of conveyance design along with proper maintenance playa large part in reducing operating costs. A knowledgeable operator can maintain a high level of safety and significantly lengthen the service life of a conveyance. Such an operator is also in a better position to determine when a major overhaul is necessary.After the decision has been made to rebuild, operators must decide who will do the overhaul. Whether the work is to be done in-house or contracted out, the goal is to achieve a conveyance recertified to ""as new"" condition. By dealing with conveyance rebuilds as an engineered product, operators can be certain they are getting a top quality product for their money.This paper deals with the engineering aspects of conveyance rebuilds. Actual examples of typical problems are discussed and corrective action outlined. Design considerations such as proper material selection, component fatigue due to cyclic loading, effects of stress concentrations and corrosion are all part of the initial design considerations that must carryover into the rebuild process. All too often equipment overhauls are done by people who are not experienced in conveyance design.As a manufacturer of mining equipment, Wabi has gained expertise over the past 70 years. By sharing this knowledge the company hopes to create a safer work environment and help to reduce operating costs."

Jan 1, 1994