Search Documents

By Ian Sherrell, Michael Pirie, Riddhika Jain

"Conventionally, direct reduced iron (DRI) mixed with char from rotary furnace discharge is cooled down before separating the char via magnetic separator. The DRI must then be reheated for further downstream processing (i.e. smelting). Outotec has developed the PyroMagTM specifically to conserve thermal energy during this separation process. DRI is cleaned by feeding hot particles directly after reduction onto a rotating surface just above a stationary magnet assembly. This allows hot feeding of the clean DRI to the downstream equipment which renders the entire process more energy efficient.Continuous testing of the PyroMagTM was performed to verify design and separation. Because the use of DRI/char was not practical for test use, the pilot plant testing was conducted using a magnetite/sand mixture heated up to and beyond the Curie temperature of magnetite. The separation was efficient for both cold and hot processing with recoveries varying from 98.6% to 99.74%. As expected, the recoveries decreased to as low as 83.99% as the temperature was increased beyond the curie temperature of magnetite (585°C). Long term separation was thermally efficient and sustainable.INTRODUCTIONMagnetic drum separators are widely used in the mineral processing industry. These low to high intensity magnetic separators are used to concentrate various magnetic material, such as iron ore, and less magnetic materials, such as ilmenite and garnet from silica and other contaminantsThere are multiple classes of magnetism based on the effect that each material displays while in and out of a magnetic field. In a simplified fashion, which is more appropriate for mineral processing, the magnetic susceptibility of a mineral is used to define it as being ferromagnetic, paramagnetic or nonmagnetic. In this respect, minerals with varying degree of magnetic susceptibility can be selectively separated with different types of magnetic separation equipment in different stages of a process flow sheet. The lower strength magnets are employed early in the process to remove highly magnetic fractions. Later stages utilize greater magnetic fields for capture of less magnetically susceptible material."

Jan 1, 2016

By N. A. McPherson, P. C. Stevens, A. J. Rigby

"There has been a consistent move in recent years to continuously cast small billets while utilizing ceramic stream protection between tundish and mould. The need to have ceramic stream protection has developed from a need to improve billet surface quality by submerged pouring. The need to protect the ladle to tundish stream in conjunction with tundish to mould protection is explained.The continuous casting of thin slabs is at the development state and will require a great deal of ceramic development to ensure the economic viability of the project. An insight is given to the main problems.IntroductionDuring the early development period o f the continuous casting of steel in the late 1940s and 1950s, much of the work was carried out on small cross section products. For example, the continuous casting of 50 mm square billets was carried out on a production scale in the United Kingdom at Barrow. Slab casting was initiated on a production basis on 100 mm thick stainless steel slabs at Atlas Steel, Weiland, Ontario. In the case of slab casting the thickness increased gradually until it was similar to Slabbing Mill feedstock , i.e. in the range 200 mm to 250 mm , although stainless steel continued to be lower at around 185 mm thick.For billets , a significant proportion of steel is now cast at around 100 mm square which creates specific difficulties when casting with a submerged pour - mould powder practice. The move back to smaller cross sections is further emphasized by the current interest in "" Near Net Shape Casting"" . If this move continues, then significant development will be required to create the refractories used between tundish and mould in the continuous casting process.Two specific areas which will receive attention are; (I) the casting of small cross section billet s; and (2) the casting of thin slab."

Jan 1, 1990

By Garth D. Kirkham, James P. Siddorn, Hendri Falck

"Abstract - As an integral part of the Geological Survey of Canada’s EXTECH III Project, a threedimensional computer model has been created of the Con and Giant gold mines in the Yellowknife Greenstone Belt. The Yellowknife Mining Camp has produced a great deal of gold (over 15 million ounces, or 400 000 kg) in the past sixty years and the prevailing assumption is that the mines are at the end of their lives. However, the potential for discovering additional resources using new ideas and technology, and maximizing use of existing data, offers an opportunity to sustain the old mining operations and maintain their contribution to the community.The objectives of this study included the compilation and creation of a three-dimensional Geographic Information System model (combining 3D subsurface data with surface information) to provide a framework for concurrent structural and alteration studies, and to encourage new exploration in the area. A secondary objective was to retain the data in digital format as a historical reference for future remediation efforts, and to document a portion of Canada’s rich mining history.The end result is a database and set of models that have been instrumental in facilitating further exploration in the area, as well as in developing targets for future exploration and mining activities. In addition, the EXTECH III 3D GIS model has made a valuable contribution toward the understanding of the arsenic remediation issues at the Giant mine, and has served as a tool in support of a variety of highly technical engineering studies and for communicating information and problems to the layman and community as a whole."

Jan 1, 2003

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By H. Ardehali, P. Lind

Many gold deposits also contain significant quantities of deleterious elements such as arsenic. Several biological pathways are possible for arsenic exposure; special care and caution must be used while undertaking metallurgical testwork on ores and concentrates that contain high levels of arsenic. Laboratory precautions pertaining to handling of airborne dust concentrations, necessary personal protective equipment, and effluent treatment are discussed.

Jan 1, 2014

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

By Dennis Martin

What is Borehole Hoisting Borehole Hoisting is the use of a hoisting plant to hoist rock, workers and materials or both, vertically through a borehole, between a mine level and surface or between two levels of an underground mine. Screen and bolt ground support on walls of 5.5 m diameter borehole hoisting shaft

May 1, 2013

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By K. Adham, C. T. Harris

Arsenic is often associated with copper, nickel and gold in sulphide deposits. This paper describes a two-stage high-temperature fluid bed reactor for the removal and fixation of As from ores and concentrates. The first (bottom) stage of reactor removes the As through a neutral roast, by volatilization as mostly sulphide species. The second (top) stage of reactor captures the As from the gas phase through oxidative fixation, as a stable iron arsenate, by reaction with an appropriate iron source (sulphide or oxide). The second stage is placed on top of the first, so that their combined function can be achieved in a simple two-stage fluid bed arrangement, with the bottom stage off-gas providing the top stage fluidization.

Jan 1, 2014

By S. E. Wolfe

The presence of helical ribs in smooth-bore round pipe results in the transport of granular solid particles m water at a much lower velocity than required to transport the same solids in a smooth pipe. The helical motion imparted to the flowing mixture effectively returns settled solid particles to the main stream. The flow may be stopped and restarted without difficulty. Due to the lower velocity required for satisfactory transport large power savings are realized. Also: due to lower velocity, the wear on the pipe walls is much reduced. For satisfactory performance, the ribs should have a high angle relative to the long axis of the pipe and the lineal spacing between adjacent ribs should be modest.

Jan 1, 1967

By S. C. Ells

Introduction An investigation of the bituminous sands of Alberta was begun by the Mines Branch, Department of Mines, in 1913. This investigation was interrupted during the period 1916-19, but was resumed in 1920. Work completed in October 1924 has included detailed topographical surveys of extensive areas, examination and sampling of principal outcrops, the mining of trial shipments, laying of demonstration pavements, and a study of methods adapted to the recovery of hydrocarbons from the crude bituminous sand. Bituminous sand consists, for the most part, of clear quartz grains, cemented together by petroleum residuum or bitumen. In form the quartz grains are most irregular, varying from sharply angular to smooth, waterworn shapes. The bitumen has a specific gravity of 1.018 and has a penetration of 9.00 mm. (77° F. 100 grams 1 sec.). The percentage of bitumen associated with the sand varies from 5 to 25 per cent. A large tonnage is available in which the percentage of bitqmen is 15 per cent or over. Production Up to the present time, production has been restricted to requirements for experimental .and demonstration work. The total quantity shipped for such purposes has not exceeded 750 tons.

Jan 1, 1925

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By W. F. J. Cosser

AN agreement having been arrived at in 1935 whereby McIntyre Porcupine Mines would purchase gravel for back-filling purposes from Hollinger Consolidated Gold Mines, the aerial gear as described below was installed. As originally discussed, the plan called for installation of a loading bin at the junction to the Hollinger tram, so making the McIntyre tram an entirely separate unit. The experience of the Hollinger engineers, however, went to prove that the operation of a bin (remote from sources of heat) should be avoided if possible, owing to the severe winter conditions (35° to 40° F. below zero).

Jan 1, 1938

By John E. Udd

The stability of a rock mass is influenced by the presence of discontinuities. In assessing stability, it is required that one should know the frictional and cohesive properties of these contained weaknesses. In the study performed by the authors, a number of samples of diamond drill core containing open discontinuities were tested in shear. The results obtained were compared with values which resulted from back analyses of instabilities in the field.

Jan 1, 1979

By E. Godfrey

The average man one meets on the street thinks of an explosive as a medium of death and destruction, something unstable which should be given a wide berth, because he knows little or nothing about its use or its stability. Briefly, explosives are compounds that develop very large quantities of heat and gas in an extremely short time and in a small space, thereby exerting enormous pressure upon surrounding bodies, and by the rapid expansion of this highly heated gas are able to perform a considerable amount of useful work. The amount of heat generated and the volume of gas produced by the decomposition of an explosive determines the amount of mechanical work it can do, and the time occupied by its change from solid or liquid condition to gaseous condition determines its shattering effect. Explosives manufactured by reputable people are not extremely dangerous, on the other hand they are quite safe if handled in a proper manner. Furthermore, before an explosive can be placed on the Canadian market a sample must be submitted to the Explosives Division of the Mines Department, who may condemn or permit its manufacture, according to their findings regarding its safety in handling and its stability during storage.

Jan 1, 1926

By Norman Lecuyer, Jacque Nantel

"The Chadbourne Project, located within the limits of the town of Noranda, Quebec, will make use of backfill materials to fill the voids left by the mining of stopes and pillars. A series of tests were conducted on different mixtures of slag and pyrrhotite tailings materials to evaluate their properties. The tests are described and some pertinent results are given in the paper.IntroductionThe Chadbourne Project is located in the centre of the Town of Noranda, Quebec, with houses as close as 120 m from the blasting operations. The ore is mined using the vertical crater retreat method. The voids left by mining activities will be filled. A program of pillar recovery will follow.Considering the proximity of houses and the need to recover pillars, the backfill program must be carefully laid out. No subsidence can be tolerated on surface.With these objectives in mind, a test program was undertaken by Nantar Engineering Limited and Queen's University to evaluate the possible ba ckfilling alternatives available to Chadbourne. One of the possibilities retained was the use of a backfill composed of broken slag material from the Horne Smelter and pyrrhotite tailings deposited on the Horne's pond a number of years previously.The back fill used at the Horne Mine until the mine closed in 1975 was composed of a mixture of 97% granulated slag and 3% pyrrhotite tailings. The tests leading to its use underground at the Horne Mine were described by Patton in 1952. The structural properties of the Horne backfill were ""intuitively"" known; it was agreed by all at the Horne Mine that the backfill was behaving remarkably well. Some were labeling it ""the best backfilling material in the world"". Its strength was said to be that of a weak concrete. All of the preceding indicate that the Horne backfill had never had its structural and other properties determined in the laboratory."

Jan 1, 1983

By Stavros A. Argyropoulos, Radhakrishna Valiveti, Bernard Closset

"The use of microprocessors in metallurgy is currently increasing at a very fast rate. A large number of companies are offering systems ""off the shelf"" which are aimed at the data acquisition and process control market. There are two main drawbacks to these systems: first, they are usually quite expensive, and second, they are not completely compatible with the target metallurgical application. An alternative is to develop a microcomputer-based system "" in lab "".A dedicated microcomputer system has proved to be very useful in many metallurgical research applications(1,2)). However, in this system the analog input signals had to be transferred over long distances , and significant noise was introduced despite the use of shielded cables. In order to overcome this problem a network of low pass-filter s was designed and built. The usage of the abovementioned system brought the need to digitize the analog signals in-situ and transfer the digital signals, which are much less susceptible to noise over very long distances. This distinctly different design philosophy has become a reality with the evolution of microprocessor technology over the last few years. This design philosophy is utilized in this development."

Jan 1, 1984

By J. Budac, R. Kofluk, S. Mankasingh

Stainless steels such as 316L or 304 are normally relatively resistant to attack by nitric acid. However research at Sherritt International’s Fort Saskatchewan Operation reveals that when the stainless steel is immersed in an aqueous system in which nitric acid is used to dissolve metals such as cobalt or nickel, the steel can be seriously corroded. Sherritt is patenting a simple process for arresting the corrosion via the use of copper. This process is expected to substantially eliminate corrosion in processes where nitric acid is used to dissolve metals attached to a stainless steel substrate.

Jan 1, 2014

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954