Search Documents

By D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrate identified gold to be mainly present in the form of a solid solution in pyrite. This gold distribution resulted in a poor extraction yield of 55% by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction has led to a gold extraction yield of 96.5%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and uses a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a membrane-less electrolysis cell. The extracted gold was recovered over activated carbon in column and the gold depleted brine was treated for impurities removal and recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Aug 1, 2013

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By Marty Hudyma

Large seismic events have been reported in mines in the Sudbury mining camp for more than 70 years. Nevertheless, no detailed record of the events has been compiled. In 2008, the Sudbury Regional Seismic Network (SRSN) research project was initiated to collect more accurate data with regard to the magnitude and locations of mining-induced seismic events in and near the mines in the Sudbury Basin. The data is used to better understand the mechanisms of the events and cause-effect relations between mining and seismic events. Through the collection of a central database of large seismic events, new insight is being be gained into why some mines are much more prone to large events than others. Fifteen low cost seismic stations have been distributed throughout the Sudbury basin. The data from each seismic station is uploaded to a central server using the internet. Data recorded on the SRSN is processed on a daily basis, and a weekly summary of blasts and events is issued to project sponsors. Seismic events smaller than local magnitude +1.0 have been identified and located. Event location accuracy is less than 2 kilometres, however, many events have been located less than 1 km from a mine. The SRSN fills a seismic monitoring gap between the in-mine microseismic monitoring systems and the earthquake monitoring system operated by the Geological Survey of Canada. Since July 2008, more than 600 mine blasts and more than 450 mining-induced seismic events have been recorded in the Sudbury basin. This paper primarily discusses the technical aspects of the design and operation of the SRSN. The SRSN is a Canadian Mining Industry Research Organisation (CAMIRO) research project, with industry sponsorship and support from FNX Mining, Itasca Canada, Vale Inco and Xstrata Nickel.

Oct 1, 2010

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By T. G. Edgeworth

Some of the historical background of the industry is reviewed, with reference to the different types of reduction cells in use for aluminum smelting. Factors to be considered in cell des1gn involve capital, power, and operating costs. The trend is apparently toward larger cells. The industry is studying new construction materials for cell linings, as well as alternate electrolyte compositions and other design changes which will improve productivity and energy efficiency. The aluminum smelting activity in other countries is briefly reviewed. TODA Y'S industrial production of aluminum is still based on the simultaneous discoveries made in 1886 by Charles Martin Hall in Ohio, and Paul Heroult in France. Up to that date, only about 50 tons of aluminum had been produced in the world, and the price at that time was about $5 per pound. Sucl1 figures must be contrasted with the present world aluminum smelting capacity of over five mil-lion tons per year, and a price of about 25 cents per pound.

Jan 1, 1962

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By N. Lecuyer

"During early 1980, pre-production work commenced at the ""Les Mines Gallen"" project, north of Noranda, Quebec. As a result of the acid mine water associated with this property, a major pre-production phase included the installation of a water treatment plant to render the water environmentally suitable.This paper emphasizes the planning, installation and operational factors of the treatment plant necessary to the success of the mining operations and the maintaining of a clean environment.Introduction,T he Gallen Project is a zinc, gold and silver open-pit mining operation approximately 10 kilometres north of Noranda, Quebec. This property has a long history, with initial diamond drilling done in the early 1930s and underground mining taking place between 1953 and 1962. This property was reactivated in 1980, with production scheduled a t a rate of 45,000 ton s per month.Included in the reactivation plans for the property was the installation of a water treatment plant to treat the acidic mine water.Plant DesignThe requirements for the Gallen water treatment plant were two-fold. Firstly, it was necessary to neutralize the acid water and secondly to produce a sludge containing metal hydroxides and sulphates which would be stable when stored, and a clarified overflow meeting governmental regulations to be discharged to the environment.The flow sheet (Fig. I) will explain the process in treatment of the acid water.Acid mine drainage is treated with lime to increase the pH to 9.50. Metals in solution are precipitated as metal hydroxides and the 504 as calcium sulphate. The precipitate slurry is then aerated to convert ferrous iron to ferric iron, which is more stable for storage and disposal.The precipitate is next flocculated with a polymer flocculant and settled in the thickener to produce a sulphate/Hydroxide sludge and a final effluent discharged to the environment."

Jan 1, 1983

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013

By R. E. Ray

"As real estate for new development in urban settings becomes scarce, commercial high rises are being constructed above open passenger rail tracks and vehicular roadways. Rail and roadway overbuilds are treated as tunnels requiring emergency ventilation systems for train or automobile and truck fires. The value of floor space in residential and office towers poses challenges to engineers responsible for designing fan rooms and shafts for tunnel ventilation systems within the towers. This paper describes a case study of the unique incorporation of tunnel ventilation fan plants in the overbuild structure of a passenger railyard and an adjacent roadway.INTRODUCTIONTunnel ventilation systems are required for passenger rail and transit (subway) tunnels by the NFPA 130 Standard for Fixed Guideway Transit and Passenger Rail Systems, and the NFPA 502 Standard for Road Tunnels, Bridges, and Other Limited Access Highways requires tunnel ventilation systems for vehicular (road) tunnels. Passenger rail and transit (subway) tunnels are typically ventilated with a series of shafts placed longitudinally along the tunnels to provide piston relief for normal train operations and emergency ventilation of train fires utilizing reversible axial flow fans. The shafts are incorporated in dedicated ventilation buildings that house the tunnel ventilation fans and starters, switchgear to power the fans and other equipment and systems in the building, Programmable Logic Controllers (PLCs) to control fan operation with Supervisory Control and Data Acquisition (SCADA) software, and HVAC fans and ductwork to ventilate the spaces in the building. These ventilation buildings may also provide access to the tunnels below with ingress/egress stairs for use by first responders and firefighters entering the tunnels and train or transit system passengers exiting the tunnels in an emergency. A photograph of a passenger rail ventilation building that encompasses four tunnels is shown in Figure 1."

Jan 1, 2019

By K. P. Wright

THREE OF the gold mines in the Red Lake Camp operates fluid bed roasters in their milling circuits. The mines are Campbell Red Lake, Cochenour Willans, and Dickenson. The roasters are used for the autogenous roasting of a flotation concentrate for subsequent gold recovery by cyanidation. Cochenour and Dickenson operate single stage reactors, whilst Campbell use a two-stage system. Ore treated by the mines is similar in that the major part of the gold is associated with arsenopyrite. Other sulphides present are pyrite, pyrrhotite, stibnite and sphalerite. Gangue minerals are mainly quartz, with carbonates and talc. Mineralization is, for the most part, extremely fine, and there is intimate association between sulphides and quartz, so much so, th at a picked specimen of apparently massive arsenopyrite will frequently contain as much as 80 per cent gangue. Gold recovery by straight cyanidation on this type of ore would not be higher than 80 per cent and

Jan 1, 1961

By N. H. Grace

"IntroductionA STRIKING FEATURE of the past twenty years has been the application of organized scientific and industrial research to problems of national defence and security and to the development of our natural resources. It has been shown that effective research improves public health, increases the productivity of land, makes mineral wealth available, and increases the efficiency and productive capacity of industry. Alberta is a region bounteously provided with a variety of natural resources, and the Province has entered into a period of unprecedented industrial development. There is, surely, a great opportunity to bring scientific research to bear •on problems associated with the development of these natural resources.I propose to spend a little time discussing the term 'research', indicating something of the various types of research and those fields which appear to •be the particular responsibility of government bodies. It seems logical, also, to outline the course of development .of industrial and scientific research in the English-speaking world during the past twenty-odd years.Research is investigation, examination, or enquiry, and involves the application of human thought, and actions, to the unfolding of new knowledge. That knowledge may assume a variety of forms. Fundamental knowledge may be new facts related to some form of matter, to motion, space, thought, and so on. Those engaged in applying the natural sciences have no monopoly on research as this term is equally valid for those engaged in obtaining, sorting, relating, and interpreting the facts of history, literature."

Jan 1, 1952

By K. W. Major

"This chapter outlines the organization of mine/ mill complexes in Canadian mining companies. Many factors unique to the Canadian mining industry will affect the design of the organization in the future: geographic location, the size and the type of orebody, etc. Mining companies cannot choose where new operations will be located, that is dictated by the location of the orebody. New mines are seldom started near established communities. Rather, the towns usually grow up near the mines. The remoteness of most Canadian mining operations has caused severe problems in attracting and/ or retaining all levels of employees. This means that training has a high priority within each operation.Another factor affecting mine/ mill organizations is the size of the operation. Larger operations generally require more departments and increased specialization to manage equipment and manpower effectively. Thus, for mine/mill complexes, organizational charts are less standardized than in other industries. It is often necessary to organize around the work force rather than develop a chart and then acquire the trained personnel to fill the diagrammed positions.The information presented in this chapter has been derived from the responses received from a survey of Canadian mining operations.Principles of OrganizationOrganization can be defined as deployment of personnel to accomplish definite goals. In the mining industry, the major goals are typically the projected number of tons and grade of ore mined on a daily, weekly, monthly and yearly basis. Organizing involves establishment of authority relationships with provisions for both vertical and horizontal co-ordination within the company structure. Vertical co-ordination is the delegation of responsibility and communication of goals and reporting of progress between the supervisor and subordinate. Horizontal co-ordination is communication between departments at positions of equal authority to determine methods of achieving predefined goals. The organization structure must reflect the objectives and plans of the company, and must clearly define areas of authority.Two criteria for effective organization are departmentalization and manpower planning."

Jan 1, 1989

By D. R. Keck

"SINCE the .Canadian Chemical Company has no direct connection with mining operations, and I have had no experience with mining, there is little I can tell you that you do not already know. However, we have had considerable experience with certain types of metallurgical problems and I would like to discuss with you some of these problems and their solutions by our metallurgists.In order to acquaint you with the type of plant and processes to be employed at Edmonton, I would like first to take a few .minutes to trace briefly the history -of the Canadian Chemical Company's affiliate, The Celanese Corporation of America. In the early •part of the twentieth century, two young Swiss brothers, Camille and Henri Dreyfus, received their P.h.D. degrees in chemistry. They were extremely interested in work which was being carried on at that time to find a suitable synthetic fiber that could compete with natural fibers, both quality and price-wise. Early man-made fibers were both coarse and hard to dye. The Doctors Dreyfus• poured all their earnings into research and ultimately developed cellulose acetate filament. During World War I, the Dreyfus brothers were invited to the United States to produce cellulose acetate 'dope' for airplane wing coverings. Dr. Camille Dreyfus built the first American plant for fiber production at Cumberland, Maryland, in 1924.Due to resistance of textile mills to the new fibers, Celanese was forced to set up its own dying, weaving, and finishing mills to prove the new materials. Through the years, however, this operation has •been retained primarily for fabric development purposes,.. with the majority of the acetate being sold to other textile mills."

Jan 1, 1953

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By S. H. Seyedein

A mathematical model was developed to study fluid flow and solidification in a single-roll casting system. Fluid flow coupled with energy equations were solved numerically using a finite volume method. A body-fitted coordinate transformation technique was adopted to handle the irregularly shaped domain. In order to couple the continuity and momentum equations, a SIMPLEC algorithm was used. A fixed-grid enthalpy method was considered to model the solidification in the system. The turbulence effect on flow field was modeled using a low-Re k-e model The model developed in this work was further run under various conditions to optimize the operating parameters of the process.

Jan 1, 2004

By U. Troncoso

Mantoverde is a heap leach-SX-EW operation that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has been steadily increased to reach 62,000 ton in 2005. The forecast copper production for 2006 is 60,300 ton for an ore treatment rate of 9.5 million ton. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. Several improvements in the heap leach process have been implemented to cope with the higher ore throughput and copper production. However, the solvent extraction plant has remained unchanged which has resulted in a lower availability of raffinate solution and, as a consequence, in longer leach cycles. Different studies have been undertaken in order to optimize the solution management system at Mantoverde, including column test work aimed to reduce the leach cycle and solvent extraction plant modifications aimed to increase the raffinate solution availability. The test work program and the economical evaluations carried out, as well as the conclusions and recommendations obtained, are discussed in this paper.

Jan 1, 2007

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By H. W. McGerrigle

The St. Lawrence Valley of Quebec lies in an earthquake danger zone, the main centers of which appear to be Murray Bay, Montreal and Quebec City. This paper compares conditions in this "earthquake zone" with those of other, currently more active, earthquake zones of the Earth, deals briefly with the mechanics of earth movements and outlines the means by which earthquakes are re-corded. An account is then given of the earthquakes which have occurred in the Province of Quebec -from that of 1534-35 to the earthquake of 1925. A 50-year frequency cycle is implied. The general conclusion is that the 11robability of future earthquakes should be given more consideration in the construction of buildings in the St. Lawrence Valley region.

Jan 1, 1966

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By V. C. Wansbrough

First, permit me to say with what very great pleasure we find ourselves assembled in this most ancient and honourable city of Quebec. It is a city which we deeply respect as the fountain-head of the culture of French-speaking fellow citizens, and the seat of government of a province which is steadily recording new achievements in Canadian mining. Such achievements prove what can be accomplished when enlightened and progressive government policy, technical and scientific competence, and private initiative pull forward together in harmonious rhythm. It is a most happy and auspicious event also that the guiding control of the affairs of the Institute and of the fine traditions of provincial administration have for the past year been united in the person of our honoured President, Dr. A. O. Dufresne. This year, again, we have bad prepared for us by our hosts a splendid programme of technical sessions and social entertainment. Each year we pay an unspoken compliment to the Institute, expecting as a matter of course nothing but the highest standards in both these spheres. In its annua1, semi-annual, and regional meetings, in the constant activity of its local Branches, the Institute continues with marked success to perform its great dual service, social and educational. We are all its beneficiaries to the extent to which we choose to profit by participation in its affairs. But, one imagines, to none are the advantages of Institute membership more valuable than to young men embarking on their professional careers.

Jan 1, 1951