Search Documents

By M. T. Ho, D. E. Wiley

The iron and steel industry accounts for almost 5 % of the total world CO2 emissions. Optimisation of the steelmaking process has led to significant reductions in the energy intensity to the point where it is now close to the thermodynamic limit. Further reductions are not likely to be achieved with efficiency improvement alone and will require the development of novel or breakthrough technologies. This paper will show the costs of implementing CO2 capture at direct atmospheric emission points for a number of iron and steel production processes. These include a conventional process, top gas recycling processes, the Corex and Hismelt smelt reduction processes and the Midrex direct reduction process. Depending on the point source emission, costs of capture with existing chemical absorption technology at iron and steel plants can be similar to capturing CO2 at pulverised coal fired power plants.

Jan 1, 2015

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By D. Kershaw

"A world-scale surface mining operation is associated with the Syncrude Oils ands Plant. Each day over 300 000tonnes of oils and are mined and transported to the process plant to produce 129 000 barrels of synthetic crude oil.Examples of research and maintenance engineering programs which have resulted in substantial gains in dragline and bucket wheel conveyor system productivities are discussed. Two central themes within these programs, which go beyond the usual technical support associated with a large surface mining operation, are pursued:1. the approach taken to determine the causes of component failures and provide Syncrude performance specifications to allow manufacturing industry to respond with more appropriate products; and2. systems and equipment studies which have led to higher productivity in the major mining equipment and the development of an auxiliary feed system.IntroductionA world-scale open pit mining operation is associated with the Syncrude Oils ands Plant located near Fort McMurray in northern Alberta. Over 300 000 tonnes per day of oils and are mined and transported to the process plant. Fifty million barrel s of synthetic crude oil were produced in 1987, which represents 10010 of Canada's crude oil requirement.following tree clearing and surface drainage, overburden is removed by mobile equipment ahead of oils and mining. Draglines excavate the 40 m depth of feed grad e oils and which is windrowed on the dragline bench. Bucketwheels reclaim the oils and from the windrows for transport by conveyor systems to the extraction plant surge pile.The Syncrude mine is operated in four essentially equal quadrants, each serviced by a dragline and a bucketwheel conveyor system. The mining face in each quadrant is approximately 2 km long and reclaimed oils and is transported by 1830 mm shift able conveyors over distances up to 6 km. Individual conveyors vary in length up to 2500 m.The Syncrude plant started operating in late 1978, and Figure I shows the mine production history through to the end o f 1987. Annual production volumes have increased from 50 million tonnes of oils and in 1979 to 105 million tonnes in 1987.The period from 1982has seen a change in operating philosophy, away from striving for very high production rates, to operating at sustained targetted levels within the measured capacity of the equipment. Higher over-all production volumes have resulted from being able to operate for more hours at these rates. This same period has also seen much greater emphasis placed on routine inspection of the equipment and planned preventive maintenance to avoid problems which could otherwise impact on production."

Jan 1, 1990

By Jun Dai

Based upon research findings from several countries, the combination of microwave and mechanical means to break hard rock holds promise for the future. To achieve this goal, it is essential to understand the laws governing strength reduction of hard rock, such as granite, induced by microwave irradiation. Two aspects to consider are: 1) laws associated with the tensile strength of hard rock after microwave irradiation and 2) the sensitivity of different types of rock strengths to microwave energy. In this study, granite with a range of tensile strengths was exposed to microwaves for various time periods to compare the response of rocks with different strength values exposed to the same microwave irradiation. In addition, a method based on hotspots is presented to explain the mechanism by which granite strength is reduced by microwave irradiation. Granite extracted from Qinling Mountain in Shaanxi Province, China is used in the research. ?50 × 50 mm cylindrical granite specimens were exposed to microwaves at a specific power level. The strength values of the heated granite specimens were compared with those of unheated specimens. Through the comparison and analyses, relationships were determined between 1) reduction in granite strength and microwave irradiation time period, and 2) granite strength and sensitivity to a given energy of microwave irradiation. Finally, a mechanism to explain the experimental results is proposed. Research findings will aid in the design of a microwave + machine rock-breaking system for use in rock breakage in underground mines at depth and for future mine applications on earth and other planets. In addition, the experimental approach could be used to test other rock types to further our understanding of rock damage induced by microwave irradiation.

Aug 1, 2013

By J. G. Kim, B. G. Chae, D. S. Cheon, E. S. Park

The underground structures such as high-level radioactive waste disposal thermal energy storage should be designed and constructed considering thermal-mechanical characterization because of long term and/or cyclic thermal stress. High temperature changes in these structures can extend the existing cracks and generate new cracks in surrounding rock mass. In case of long term and/or cyclic thermal stress conditions, it is possible to lose the function of structures caused by the significant cracks and fracture growth in the rock mass. In this study, the critical thermal crack temperature of the granite, limestone and thermal Kaiser effect were evaluated. Experiments were carried out with the heating speed of 1.5?/min. To avoid thermal shock and target temperatures were set at 150? and 250?. In order to verify the thermal Kaiser effect, the samples were heated by 150 ? after 2-3 repetition to 250?. The generation and growth of cracks were observed through an acoustic emission measuring system. The variation of the physical rock properties was measured before and after thermal experiments. After compared with the thermal experiments using PFC2D, numerical simulations were carried out at higher temperatures (400?). The experiments showed that the initial thermal crack temperature of granite and limestone is about 35?, 32? and the critical thermal crack temperature were about 69? , and 49? , respectively. The experiments confirmed the thermal Kaiser effect of experimented granite and limestone due to thermal cyclic loading. From the numerical analysis, the critical crack temperature showed the same tendency as the thermal experiments. The P and S wave velocity of the sample after the experiment were reduced. Therefore, when heat is applied in long-term and repetitive conditions, these cracks may affect the function and stability of the underground structure. Therefore, further studies of thermal stress effects should be performed.

Jan 1, 2015

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019

By M. J. Steffens

ESPLIM is a novel separation technique that combines the advantages of solvent extraction and electrostatic dispersion but its application in the extraction of nickel by the direct solvent extraction route and the effect of high electrostatic field on the stability of organics have not been explored. These were investigated in this study and it was found that the technique allows 97% extraction of the nickel in a single stage compared with 3 stages by the conventional solvent extraction. Also, three months of exposure to 5.0 kV under simulated operational conditions had no adverse effect on the stability of organics.

Jan 1, 2005

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By H. C. Gunning

Introduction Considerable attention has of late been attracted to the area surrounding Nimpkish lake, on northern Vancouver island, by the discovery of important rich copper deposits. In less than two years some 200 mineral claims have been staked in a small area, and at least two groups have very promising surface showings. During the summer of 1929, the writer spent one month investigating the general geology and mineral deposits of the region, and, although no detailed work has as yet been done in the field or in the laboratory, the importance of the mineral discoveries and the lack of geological information available to the public warrants a preliminary paper on the district. The district is, from a mining viewpoint, very accessible. Boats from Vancouver call at Englewood, in Beaver cove, four times a week. From Englewood, a first-class logging railway, operated by the Wood, .English Company, extends to the northeast corner of Nimpkish lake. The fifteen-mile trip from the north to the south end of the lake is made by boat, two tugs being maintained by the logging company. The whole trip from Englewood can easily be made in one day. The known mineral deposits lie immediately east of the southern part of the lake, four miles or less from the shore. A fair trail, four miles ? long, leads from the lake to the Nimpkish Copper group. Apart from this trail and an old logging railway grade which follows the east side of Klaanch river for several miles, no trails exist on the southeast side of the lake.

Jan 1, 1930

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By M. Tanaka, H. Narita, K. Morisaku

"The selective separation of palladium (Pd), platinum (Pt), and rhodium (Rh) from a hydrochloric acid solution by solvent extraction was investigated using amide-type extractants, i.e., N,N,N’,N’-tetra-n-octyl-thiodiglycolamide (TDGA) and N-n-hexyl-bis(N-methyl-N-n-octyl-ethylamide) amine (BisAA). The separation experiments employed two separation schemes: (1) extraction of Pd with TDGA and that of Rh and Pt with BisAA; and (2) extraction of Rh, Pd, and Pt with BisAA. Separation scheme 1 achieved the highly selective separation of each metal. For separation scheme 2, Rh can be recovered prior to Pd and Pt, despite having a lower selectivity for Pd/Pt than separation scheme 1. INTRODUCTIONThe recent increase in the use of platinum group metals (PGMs) in industry (especially auto catalysts containing palladium (Pd), platinum (Pt), and rhodium (Rh)) has lead to their increasing waste; therefore, improvements in the recovery techniques for PGM have received significant attention. In metal refineries, PGMs are mainly separated and purified by solvent extraction (Cox, 2004). The extraction process used in INCO’s Acton precious metal refinery is one of the most famous commercial processes and is utilized worldwide. In this process, silver is first removed as a residue (AgCl), and then gold, Pd and Pt are extracted from hydrochloric acid (HCl) solutions using dibutylcarbitol (DBC), dialkylsulfide (DAS), and tri-n-butylphosphate (TBP), respectively. Finally, Rh remains in the raffinate (Barns & Edwards, 1982).The development of a successful solvent extraction process depends on the choice of the appropriate extractants. We have studied the extraction of PGM using N,N-disubstituted amide compounds (Narita, Tanaka, Morisaku, & Abe, 2004; Narita, Tanaka, Morisaku, & Tamura, 2006; Narita, Tanaka, & Morisaku, 2008a, 2008b). They are relatively stable against acids, and their metal extractability can be improved by changing the side chain length and/or introducing additional donor atoms like sulfur and nitrogen. We have recently found that thiodiglycolamide and an amide-containing tertiary amine have good extractabilities for Pd and Rh, respectively."

Jan 1, 2012

By L. Janku, G. Hancox, M. Villenueve, C. Massey

Wellington lies in a seismically active area 150 km from a subduction zone and in the vicinity of several active faults, which poses a risk to its infrastructure and inhabitants. One of these major faults, the Wellington Fault, runs through the centre of the city and across several lifelines, including the natural gas pipeline and the freshwater pipeline. The first settlement in the area was severely damaged in 1848, soon after its establishment, by an earthquake of approximate magnitude Mw 7.4 - 7.5 (Grapes, Little, & Downes, 1998). In 1855, another earthquake of magnitude Mw 8.2 generated by a nearby fault uplifted the eastern part of the current Wellington area and caused several landslides in the surrounding hills (Grapes & Downes, 1997). The Central Business District lies in the area of a sedimentary basin and partly on reclaimed land. Many residential areas, as well as some vital infrastructure, however, lie on or along the slopes in the surrounding hills. The bedrock in the area comprises predominantly the Torlesse greywacke of Permian – Late Triassic age. The greywacke is tilted to a steep angle, intensively faulted and fractured (Cook, 2001). Even though several studies in the past assessed the seismic risk in the area (e.g. Brabhaharan, Hancox, Perrin, & Dellow, 1994), the studies either focussed solely on the area of the sedimentary basin or based their assessment of the hilly terrain purely on slope morphology (slope angle). Previous studies have shown that slope shape and contrasting materials in the slope can amplify earthquake ground motions, such factors are typically called site effects (e.g. Geli, Bard, & Jullien, 1988). Any attempt to systematically quantify the site effects and consequent seismic response of the slopes and use it to predict the consequences of the next large-magnitude earthquake, has not yet been carried out. In this extended abstract we outline the methodology of a PhD research project, focussed on investigating the site effects on the slopes around Wellington and on creating representative numerical models of ‘characteristic’ Wellington slopes and materials. This extended abstract presents the methodology adopted for the assessment using the Te Ahumairangi Hill site as an example.

Jan 1, 2015

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By D. A. Pirttinen

The promotion of improved coal quality for thermal generation can benefit our national economy. The construction of electric generating facilities in Canada is expanding at a rapid rate to satisfy the demands of a rising population and new uses for electrical energy. With remaining economic water power resources in the process of development, generation from thermal sources continues to grow. The increase in thermal capability has been somewhat arrested by a de-pressed economy, widening of inter-provincial and state transmission networks and decisions to exploit certain water resources before high capital investment is further in-creased by rising construction costs. The introduction of extra high volt-age transmission lines will further delay thermal generation planning, but in due course, when the effects of restrictive factors have been dissipated, steam-electric generation from fossil fuels will rise to considerable proportions. In time, nuclear sources will contribute a growing share to thermal power, but, it is doubtful if nuclear participation will ever displace conventional fuels for steam rising, unless it can be adapted to operate efficiently for variable outputs in peaking service. It appears certain that fossil fueled

Jan 1, 1961

By H. W. Fleming

In 1955, the results of a regional, geological interpretation of the northern portion of New Brunswick were used as a basis for selecting, for intensive exploration, three areas in which structural and stratigraphic conditions were believed to be favourable. Airborne electromagnetic work, in one of these areas, provided the justification for acquiring the Murray group. Even though the initial results were discouraging, this geological interpretation, combined with the fortuitous discovery of cop• per-bearing float, was sufficient reason for carrying out further work using geochemical methods. This work finally resulted in the discovery of the Murray massive-sulphide deposit, after about eighteen months of coordinated exploration on the property. While this deposit is a typical New Brunswick-type base-metal occurrence, extensive leaching has produced a fossil gossan that rendered it an elusive target for exploration techniques of limited penetration Full credit for localizing the target area is given to the geochemical techniques, but geophysical surveys were needed to provide the necessary

Jan 1, 1961

By D. Auerswald, M. Kotze, V. Yahorava, T. Udayar

Uranium can be recovered from lower grade uranium ores (<800 mg/kg U3O8), leach residues, and waste dumps cost-effectively via resin-in-pulp (RIP). Using this technology, no solid/liquid separation or washing of the leach residues are required. Furthermore, the uranium recovery can be higher than with conventional methods. RIP technologies have, however, been perceived negatively due to concerns around potential resin fouling and losses. This paper highlights the advancements made in RIP and discusses a number of potential applications where the technology could deliver economic and consequential environmental benefits by reducing the uranium levels in the waste.

Jan 1, 2014

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010

By J. W. Griffith

"The mines in the Bancroft area of southeastern Ontario, a few kilometres west of the town of Bancroft, are in Faraday and Cardiff Townships. Three companies, known as Canadian Dyno Mines Limited, Macassa Gold Mines Limited (Bicroft Division) and Madawaska Mines Limited (formerly Faraday Uranium Mines Limited), with plants capable of handling a total of 4,()()() tons (3,629 tonnes) of ore a day, were at one time in production. A fourth company, Greyhawk Uranium Mines Limited, operated a small mine whose ore was shipped for custom treatment to the nearby Faraday mill. Canadian Dyno Mines Limited ceased operations in June 1960. In June 1963 the Bicroft Mine was closed and a year later Faraday closed because of contract completion. But in 1975, Faraday (now called Madawaska) was re-opened but closed again in 1982. During 1959, the peak year, these four mines produced an estimated 1,100 tons (998 tonnes) of uranium precipitates, which represented nearly 7 per cent of Canada's output for that year(Fig. 1).The deposits occur in pegmatitic granite dykes in a region of high-grade metamorphic and metasomatic rocks. Uranium distribution is usually controlled by the distribution of mafic minerals, particularly hematite and magnetite, and by late fractures. The best visual indicators for uranium concentration are hematite staining in the pegmatite, followed by the amount of mafic inclusions or crystals. The Bancroft area orebodies are the only known deposits of the general pegmatitic class in Canada that contained economic deposits of uranium. The principal radioactive minerals are uraninite and uranothorite. By comparison with many other pegmatitic occurrences, some of the ore bodies are unusually large, persistent in depth and relatively rich in uranium minerals. At the end of 1981, total ore reserves were estimated at 1,500,00 short tons (1,360, 000 tonnes) averaging 0.11 % U3O8."

Jan 1, 1986

By G. S. Hume

FOR MANY YEARS Canada lived in the hope of attaining a substantial production of petroleum and natural gas that, to geologists familiar with the sedimentary basins of this country, seemed an entirely reasonable expectation. There have been surges of exploration activity stimulated by oil and gas discoveries and development such as occurred in Turner Valley. However, it was not until the Leduc field in Alberta was found in 1947, and the significance of that discovery was realized, that the search became really intensive and continuons. Expansion now has become a matter-of-fact attitude based on results which would have been considered impossible of achievement a few years ago.

Jan 1, 1957