Search Documents

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014

"Automatic flotation control in varying degrees of sophistication is practiced at a number of concentrators throughout the world. Practically, the variable conditions in the flotation circuit and the difficulty in maintaining accurate instrumentation information all add to the complexity of automatic control.Further development at the Kidd Creek concentrator has resulted in a 3075 mtpd copper flotation circuit capable of running twenty-four hours a day under the direct control of an optimizing supervisory computer.Three main streams, continuously monitored by an XRF analyser, supply circuit information to the optimizing computer. Circuit efficiency calculations (from smelter contract terms) and target setpoints allow the computer to determine the economic optimum direction to move the circuit based on the grade/recovery relationship. Circuit manipulation is accomplished by precise pumping of collector and frother reaqents together with accurate control of flotation bank pulp levels. The former uses computer controlled diaphragm pumps and the latter is achieved by control loops utilizing a float type level transmitter, variable position dart plugs and a process computer working to setpoints determined by the optimizing computer.The development of a fully automated flotation circuit is by no means complete, but increased knowledge and major hardware improvements have allowed its progression to a higher level of sophistication."

Jan 1, 1983

By Manqiu Xu, Pete Winn, Steve Wilson

"In the flotation of ultramafic ores at Thompson mill, Inco Limited, CMC is used as both a floatable rock depressant and electrostatic serpentine slime dispersant. CMC, being a high molecular weight polymer, creates a serious handling problem in its introduction into the flotation processes. Typically, it is added as a 1-3% solution. This requires an enormous handling facility and makes its metallurgical gains uneconomical.Laboratory studies have shown that dry CMC addition as opposed to wet addition is feasible, as long as sufficient conditioning time is provided. Dry CMC addition into the grinding mill is also possible but its effectiveness is slightly reduced as compared to dry addition after grinding mills. Dry CMC addition using a vibratory feeder into the mill discharge is successfully applied in the treatment of ultramafic ores at Thompson mill.INTRODUCTIONManitoba Division MineralogyAt Inco’s Manitoba Division, two distinctly different sulphide ores are processed at the Thompson mill - primarily by froth flotation. The Thompson and Birchtree mines are both located within the Thompson Nickel belt. Sulphide mineralogy is relatively simple and includes both hexagonal and monoclinic pyrrhotite, pentlandite and minor chalcopyrite hosted in metasedimentary and metavolcanic rocks. The significant difference between the two mines is the amount of ultramafic rock associations in the host material. Increasingly, more of the ultramafic associated ores from the Birchtree mine are being processed through the mill with a characteristic poor metallurgy."

Jan 1, 2000

"The outlook for Eastern Canada is decreasing coal production over the next few years; however, a reappraisal of the long-term requirements and increased prices of coal could lead to a revitalizing of the industry. The market for Western coal is expanding and is expected to exceed 50 million tons per year in the metallurgical and thermal power fields. Western coal reserves are currently estimated at 119 billion tons. Technical developments in Eastern Canada include a shearer and gate-end support system to mechanically cut the stall and brushing at the tail-end of a longwall. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Results to date on the underground hydraulic experiments exceed expectations. The importance of reclamation is recognized and plans have been made to restore and re-vegetate disturbed areas and mine dumps. In Eastern Canada, experiments were started to determine the feasibility of coal reclamation from mine dumps, including one dump that is on fire. The Mining Research Centre, Mines Branch, continued to conduct research work oriented toward solving Canadian mining problems The Western office of the Centre, opened in 1970, was set up primarily to study problems associated with a resurgent coal industry."

Jan 1, 1971

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By Thomas R. Larson

"Many concentrators use re-circulating “plant” water for dilution in their flotation circuits. However, if crusher dust suppressants, ball mill grinding aids, or even agitator bearing grease are introduced into this water, and the water itself is not subject to cleaning steps, then sufficient quantities of these chemicals may appear in the flotation cells and begin to impact the flotation separation. A bench flotation procedure has been coupled with statistical analysis in order to estimate the impact of small quantities of non-flotation chemicals on flotation performance.INTRODUCTIONCleveland Cliffs produces iron oxide pellets for blast furnace feed, and is developing the capability to produce ferrous metallic products to supply a wider customer base. Cliffs manages five North American iron mines, including the Wabush mine sites in Labrador and Quebec. Based on various characteristics of the ore bodies, the flow sheets of the five mines are diverse. For example, Hibbing Taconite uses magnetic separation alone as their primary upgrading method, but Northshore and Empire use magnetic separation followed by flotation, and Tilden uses flotation alone. Last but not least, the Wabush concentrator upgrades primarily with gravity and electrostatic separation techniques.At Northshore, concentrate from the magnetic separator circuit is fed to a reverse flotation circuit. By design, the magnetic separators operate at the highest possible recovery of magnetite, as the separator tails are discarded, and relatively high silica content was acceptable to Northshore’s customers. As the steel-making industry moved toward lower and lower slag volumes, the silica content in the magnetic separator concentrate became a problem. The flotation step was added in the late 1980s in order to decrease the silica assay of the magnetic separator concentrate to meet the current customer requirements. In this setting, the flotation feed stream contains very little silica that occurs as liberated quartz particles. As the degree of liberation of the flotation feed stream is then a limiting factor for silica removal, the online grind control then was linked to flotation in the overall plant control system so that grind can be adjusted to achieve improved liberation if necessary for the flotation process."

Jan 1, 2002

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By Polysius AG

"The Lone Tree demonstration was an important milestone in bringing High Pressure Grinding Roll (HPGR) technology into hard rock applications in the mining industry. HPGRs have become standard equipment in the cement, iron ore, and diamond industries over the past fifteen years, but their use in severe duties found in the hard rock mining sector has been restricted due to high roll wear and subsequent low availability. HPGR availability has historically been limited because of frequent downtime for edge weld rebuilding as the rolls wore and short tyre life from high roll surface wear rates.Recent advancements in HPGR wear protection are now being evaluated for commercial applications in the gold and copper mining industry where this technology may offer benefits in comminuting hard and/or abrasive ores and in improving metal recovery in heap leaching applications.Proving the feasibility of HPGRs for processing competent, abrasive gold ore, Newmont Mining Corporation, the world's largest gold producer, operated an HPGR demonstration plant employing a POLYSIUS (POLYCOM) HPGR incorporating some unique wear protection, at their Lone Tree gold mine near Winnemucca, Nevada. Results of the successful demonstration are presented and evaluated in this paper.The Lone Tree HPGR demonstration plant operated for three months, from April through June 2003. The HPGR operated for 1626 hours and processed 141,000 tons of ore. This technology demonstration focused on measuring operating performance, wear characteristics, and availability of today's HPGR technology.Polysius' innovative roll surface wear protection system eliminated edge-welding downtime. Improved surface wear protection extended tyre life to predicted durations acceptable for very abrasive service. The POLYCOM HPGR is now deemed suitable for selected hard rock applications."

Jan 1, 2005

By Hamid-Reza Manouchehri

Mining & Sustainability? A Paradox?! ? Production: gradually or exponentially increasing (giant mining) ? Ore Grades: gradually declining, ? Open Cut Mining: now widespread, likely to be sustained in the future though the long-term is hard to predict as new mineral deposits are likely to be deeper ? Waste Rock / Overburden: increasing rapidly, likely to be sustained in the future and closely linked to open cut mining, especially for coal and base metals ? Economic Resources: commonly increasing but some remain stable or gradually declining, future is linked closely to exploration, technology and economics; Increasing population, changing life style and technology development, ultimately result in sustainability in mining industry to hang in the balance and continue.

May 1, 2013

By R Thomson

The use of uranium metal in non-ferrous metallurgical practice is dis-cussed with reference to its alloying behaviour and chemical activity. It is suggested that the more promising applications are in the treatment of molten metals to combine with impurities. Mines Branch work along these lines is described for copper, zinc, magnesium, aluminum and nickel alloys. It is shown that a cop-per-uranium master alloy (25 per cent U) successfully deoxidizes molten copper without detriment to the electrical or mechanical properties of the product at residual uranium levels of up to 0.8 wt. per cent. Additions of uranium to alpha brass in amounts greater than the lead impurity content were found to remove the deleterious effect of lead on hot-workability. Similar deoxidizing and malleableizing effects were found with uranium additions to nickel. It is thought that uranium forms stable intermetallic compounds with many impurity elements. A significant malleableizing effect can therefore be expected in the presence of other elements besides lead.

Jan 1, 1963

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By Eric Konigsmann

"Omai Gold Mines is a large scale open pit gold mining operation located in central Guyana, South America with a 12,000 tonne per day milling facility. Mill operations were initiated in December 1992 with commercial production beginning in January 1993. The entire operation employs approximately 120 expatriates and some 800 Guyanese nationals and is expected to produce in excess of 250,000 ounces of gold per year. The total mineable reserves contain 2.5 million ounces of gold with a projected mine life of twelve years.The milling circuits feature an SABC grinding circuit, gravity concentration and a conventional CIP gold recovery circuit. This paper will review the mill start up and ""run-in"" phase during the first year of operation. Emphasis will be placed on descriptions of start up problems and circuit modifications, mill performance trends in 1993, and personnel training and development. An outlook for 1994 is also given.IntroductionOmai Gold Mines is a large scale, open pit gold mining operation located in the Potaro district of Guyana, South America, some 160 kilometers south of the capital city Georgetown. Although there are numerous small scale gold mining ventures in Guyana, particularly with the dredging operations on the rivers, Omai is the first hard rock, open pit mine to be developed in the country. At present, this mining operation is one of the largest gold mines in South America.The Omai gold deposit has been exploited for over one hundred years. In the late 1800's, a German syndicate used hydraulicing with subsequent gravimetric separators such as sluice boxes and trommel screens to recover gold from saprolite, a soft, oxidized, claylike mineral which covers much of the claim area. Through the early 1900's and up until the 1950's, numerous mining companies including Anaconda Mining Co. Ltd. explored and drilled the Omai deposit but the technology and low gold price of the day made the reserve uneconomic to develop."

Jan 1, 1994

By M. Y. Solar, W. G. Davenport

Most of the recent growth in nickel demand has been for the production of stainless steels and virtually all of it has been satisfied by new ferronickel and nickel pig iron projects. But "good" laterite resources are more and more difficult to find: Ni grades are decreasing while Fe contents are increasing and SiO2/MgO ratios vary from 1 to 3 and even higher if limonites are included. Predicting the smelting behaviour of such ores requires a more fundamental understanding of the thermodynamics of these systems in commercial operations. One valid question is thus whether these furnaces are at thermodynamic equilibrium or not. The present paper investigates this question, compares calculated and measured O2 partial pressures and mechanical/chemical slag loss ratios and concludes that ferronickel furnaces are not at thermodynamic equilibrium. This departure from expectation is actually to the operators’ advantage: the targeted ferronickel grades can be obtained at lower reduction potentials than calculated from pure thermodynamics.

Jan 1, 2014