Search Documents

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemicals are added to flotation circuits directly and indirectly to control issues such as scaling and dust in other areas of the operations. Since dosage levels are generally not high, a standard laboratory float test may not be able to determine the effect of a specific chemical on the productivity of the flotation circuit. This paper presents a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5–100 g/t). Results indicate that this protocol helps to predict potential interference by a particular chemistry on the flotation circuit.RÉSUMÉ Certains produits chimiques ne servant pas à la flottation sont ajoutés directement et indirectement aux circuits de flottation afin de contrôler des problèmes tels que l’entartage et la poussière dans d’autres secteurs des opérations. Étant donné que les niveaux de dosage sont généralement faibles, un essai standard de flottation en laboratoire pourrait ne pas être en mesure de déterminer l’effet d’un produit chimique spécifique sur la productivité du circuit de flottation. Le présent article définit une procédure d’essai en laboratoire qui utilise des études cinétiques de flottation pour vérifier l’effet de doses normales à extrêmes de produits chimiques antitartre et anti-poussière (5 à 100 g/t). Les résultats indiquent que ce protocole aide à prédire l’interférence potentielle d’un produit chimique particulier sur le circuit de flottation."

Jan 1, 2016

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By B. E. Shaw

This paper describes the use of the Free Piston Valve, and a simple hoist brake control system, which has been developed over the last two years, greatly improving the performance of low-pressure brake engines. The basic control system is outlined, with sections devoted to emergency trips and differential braking, and the application of the system to deep shaft hoisting is discussed.

Jan 1, 1966

By T. G. Joseph, E. Lampard

ABSTRACT: Surface mining operations must manage variability from within their operations as well as variability imposed upon them by external forces. A framework to manage both internal and external variability through the continuous review and adjustment of a mine plan during active mining lifetime operation is introduced, to minimize lost production and maintain operational safety. The observational approach of “observe, evaluate, interpret, predict, and adapt” is employed as the backbone of this approach. Although written with a surface mining operation in mind, the framework outlined in this paper would be equally applicable to any mining or processing operation.

Jan 1, 2011

By A. M. Christie

Acknowledgements The following account has been compiled mainly from records and maps of Eldorado Mining and Refining (1944), Limited, hereinafter called the Crown Company. This work was done under the supervision first of R. F. Murphy, Chief Geologist, and later of E. B. Gillanders, Eldorado Mine Manager and Manager of Eldorado Exploration Division. W. F. James and B. S. W. Buffam are consulting geologists. Since 1946, S. N. Kesten has supervised geological work for the Company in the Goldfields area. Where maps of Eldorado properties have been included in this paper, the name of the geologist who examined the property is acknowledged on the map. Outline of General Geology The geology of the area is described in the Goldfields and Martin Lake preliminary maps of the Geological Survey and accompanying Paper 49-17. In brief, the Tazin series of Precambrian age, consisting mainly of sediments with minor interbedded volcanics and basic intrusives, is intruded and replaced by granite, now generally gneissic. The late-Precambrian Athabaska series of conglomerate and arkose, with interbedded basalt and andesite flows, rests unconformably on the older rocks. All these rocks are cut by small diabase dykes. The geological terms used in this paper and in the accompanying figures are standard with the exception of the term 'mafic rocks'. These include all the basic or dark coloured rocks of the Tazin group, such as amphibolites, biotite schists, and chlorite-epidote rocks (greenstones), whether they be of extrusive, intrusive, or sedimentary origin.

Jan 1, 1949

By C. Fleming, J. R. Goode

ABSTRACT: Data were produced from two uranium project studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. In both studies, excellent metallurgical results were produced. The loaded resins were eluted with strong sulphuric acid and recycled through RIP circuits in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low. Metallurgical results from these two campaigns are presented, along with a case study economic analysis of RIP versus the alternative processes of counter-current-decantation or filtration and solvent extraction.

Jan 1, 2011

By Suzie Nantel

Crystalline igneous rocks, known commercially as granite, are exploited in Quebec f rom more than twenty-five quarries for building, ornamental and monumental purpose$. Quebec is the main Canadian producer of construction granite, accounting for nearly 90 per cent of total production. Jn the last three years, this industry has experienced an important growth due to improved marketing and use of modern equipment in rock-cutting and polishing. Jn /983 a 35 per cent sales increase is forecast. The main rock varieties extracted are the following: porphyritic pinkish grey granite and green charnockite from Riviere-dPierre, mahogany brown granite and black anorthositic rock f rom the Lac Saint-Jean area, fine-grained pink granite from Guenette, coarse-grained brown quartz monzonitefrom SaintA lexis-des-Monts. All these rock types occur in the Grenville tectonic province whereas a medium-grained, light grey granite, Devonian in age, is extensively being quarried in the southern part of the Appalachians. In the Superior province a greenish black diabase and a deep red granite are extracted. Search for new varieties and deposits is actively being carried out by prospectors and by the minis/ere de /'Energie et des Ressources du Quebec following growing demand for granitic and gabbroic rocks as dimension stone.

Jan 1, 1984

By Lionel A. York

This paper outlines the type of water-bearing formations encountered in the Prairie Sediments and describes a method for effectively sealing these zones in order that shaft-sinking operations may be carried out with safety. Details are given of the procedure for carrying probe holes ahead of the shaft bottom. These probe or grout holes are employed for establishing a series of overlapping grout covers around the proposed shaft excavation to safeguard against large inflows of water during sinking. The pattern and length of grout covers cannot be standardized, and each cover needs to be specially designed to suit the varying ground conditions. In order to provide effective protection through the Prairie Sediments, the number of holes in any one cover would not be less than 8, and possibly as many as 64 would be required in certain zones. The length of covers would vary from 100 ft. to 250 ft. Emphasis is placed on the need for obtaining accurate geological and water information from exploratory holes, drilled in the shaft vicinity, in order to effectively plan all grout covers.

Jan 1, 1964

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By Chris Twigge-Molecey

"Over the last 50 years there has been a dramatic evolution in the metallurgical engineering field in Canada. In the 60s the field was dominated by large American and UK groups, often selling major process and equipment packages. The local content was limited to wrap around facilities and the civil and structural work. The mining and metallurgical companies had strong internal teams to lead these projects. Over the decades and business down cycles the large foreign contractors disappeared or re-structured and the mining companies largely shed their engineering and project management groups. The resulting gap was filled by a cadre of local specialist engineering companies, some of whom have grown to be world leaders in the field. The paper traces this evolution and examines the underlying causes and consequences."

Jan 1, 2015

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By M. Myllymäki

"Pre-treatment of mill feed in a minerals processing plant enables for higher production efficiency per ton of product, reduction of consumables and diverting mineral feed types. Sensor based particle sorting allows for pre-concentration of the run-of-mine (ROM) material prior to other concentrating process. Various sensors provide different responses from the minerals in measured particles. The capability of “accepting” or “rejecting” particles based on sensor responses is investigated in specific test work for each project. Modern sorting machines use pneumatic actuators to divert the reject particles from the material stream. This paper discusses the incorporation of ore sorting test work in processing and plant design. When taking the effects of a sorting circuit into account early in the process planning phase, the downstream process can be adequately sized and impacts evaluated. Potential benefits include but are not limited to increased head grade, lower tonnage to the mill, increased mining operations, removal of deleterious elements and changed properties in the process feed. In a case study we present the Keliber lithium project in central Finland. The plant will produce 9000 tons of lithium carbonate per year from a spodumene ore. Ore sorting and flotation tests were carried out in laboratory and pilot scale. Process models were designed and simulations performed using Outotec’s HSC Chemistry Simulation software. Changes in the flotation performance (grade, recovery, impurity levels) were simulated with and without the pre-concentration of the ROM material. The metallurgical performance and mine economics of the different operational scenarios were evaluated using the Ore-Met optimizer module of the simulation software.INTRODUCTION Challenges in the recent years such as declining ore grades, increasing energy prices, scarcity of water and increasing environmental regulations raise the demand for more efficient processing technologies. Sensor based sorting offers a method for pre-concentration or waste rejection at an early process stage. The technology analyzes each rock particle separately for their unique physical and chemical properties, and diverts the particles into separate material streams by high pressure air jets. Successful implementation relies on ore heterogeneity, differential sensor response and suitable feed preparation."

Jan 1, 2018

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By H. T. Kennedy, D. L. Flock

"The project described in this pa-per was undertaken to provide a more thorough understanding of the effect of contamination by drilling fluids on the electrical properties of porous systems. The basic work per-formed was filtration tests on both consolidated and unconsolidated sands and the determination of their resistivity profiles with the aid of screen-type electrodes spaced at convenient intervals along the core.Four drilling fluids were selected, ranging in resistivity from 447.0 ohm-cm. to •5.76 ohm-cm. The permeability of three unconsolidated and four consolidated cores, on which resistivity measurements were made, varied from 1,257 md. to 4,560 md. Five additional cores with permeabilities as low as 49 md. were tested to investigate the effect of permeability on the depth of invasion of drilling fluids.The effect of drilling fluid invasion on resistivity profiles was determined on cores containing brine only, and on those containing 80 to 90 per cent oil and 20 to 10 per cent brine. The study included measurements of (a) clay content of different sections of the core, (b) saturation of the invaded fluids and oil in different parts of the core, and ( c) changes in resistivity as a result of gravitational re-distribution of fluids and diffusion of electrolytes.The data showed that the resistivity of an invaded core is, as was expected, controlled by the resistivity of the filtrate, the resistivity of residual core water, the resistivity of the clay particles, and the amount and distribution of the filtrate, clays, residual oil, and brine. In most cases there was a significant increase in resistivity owing to the presence of clay solids which had invaded the core. The change in resistivity, as a result of the diffusion of salts, was substantial after a period of five hours. There is evidence in some cases that the residual oil and core water saturations of the unconsolidated cores, after substantial invasion, are very low, indicating almost complete displacement by invading fluid."

Jan 1, 1959

By A. Otsuki

"This paper discusses the primary collector adsorption onto a sulphide mineral in mixed collector systems to understand its adsorption mechanism. UV-vis measurements were performed to identify the primary collector concentration adsorbed on pyrite, and the adsorption kinetics under different conditions were compared to distinguish their difference between single and mixed collector systems. Small amount of secondary collector addition prior to the primary collector addition significantly improved the adsorption kinetics of primary one. The result was explained by the combination of two previously proposed mechanisms (i.e., different adsorption site mechanism and multi-layer product mechanism). This study showed UV-vis measurement as an effective tool to study mixed collector adsorption behaviour.INTRODUCTIONCollectors are surfactants composed of heteropolar molecules with a non-polar and a polar group (Lotter & Bradshaw, 2010). In a froth flotation process, the function of collector is to improve the hydrophobicity of target minerals and selectively float them with the aid of gas bubbles. Because of the chemical or physical attraction between the polar group and the mineral surfaces sites, collector molecules adsorb on the particle surface with the non-polar group assigned towards the bulk solution (i.e., water), thus the mineral particle surface becomes hydrophobic (Wills & Napier-Munn, 2006).Thiol collectors are major collectors widely used in sulphide mineral flotation. Potassium amyl xanthate (PAX), dithiocarbamate (DTC), dithiophosphate (DTP), mecaptobenzothiazole (MBT) are some common thiol collectors. Previous studies reported that some mixed collectors systems enhanced the flotation performance (e.g., Bradshaw, 1997; Bradshaw et al., 1998; Rao & Forssberg, 1997). Thiol collector mixtures are often used in the flotation of sulphide ores, and discussed with the synergistic benefits (Bradshaw et al., 1998) which include lowering the total collector dosage requirements, improving the sulphide recovery and the rate of flotation as well as the improving the froth characteristics. The current paper mainly considered the mixture between two thiol collectors (PAX and DTC, considered as a weaker and selective collector, and stronger and less selective collector, respectively (Bradshaw, 1997)) to further understand their adsorption mechanism that should assist in improving the flotation performance of refractory gold ore."

Jan 1, 2016

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By H. R. Banks

SHORTLY after the commencement of operations at the Sullivan concentrator, the use of a pilot table was instituted in order to present a visual control of various products by showing the amount of galena still present in the tailing from several stages of flotation. Among the products so treated, the final tailing was later included. It was sratifying to note that very little free galena was escaping, but a fine streak o a whitish mineral appeared at the concentrate zone. This mineral was identified as cassiterite. The amount was small and the newly recognized component in an already complex ore was considered primarily as of academic interest. However, the problem of recovering a usable metal was intriguing and, as opportunity presented itself in temporary lulls in research on Sullivan and other ores, the concentration of tin was a useful 'bit of knitting' to go on with. It was recognized from the start that the bulk of the mill tailing would have to be floated and the residue subjected to gravity treatment. Since one of the predominating features of Sullivan concentration operation has been the necessity of fine grinding, the problem of gravity concentration was thereby intensified. Several batch runs were made, and sufficient pulp was treated to produce about one ton of final tin concentrate assaying 67 percent tin. The overall recovery was under 30 percent and the estimated profit at full tonnage was only marginal. Testing was resumed several years later, when the price of tin again appeared attractive, in an attempt to develop a more compact plant with better recovery of tin. The weakness of the original plan of concentration was the large number of tables required to treat a feed so low in tin.

Jan 1, 1941

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By Jon Errey, Aleksandar Petrovic, Karl Haase

"Developing a gold deposit of this magnitude in the Amazonian jungle of Guyana posed many challenges. This paper describes not only the process & logistical challenges arising from the remote mine site location in a tropical environment with a local industry unaccustomed to recent large scale gold mining operations, but also the innovative technical solutions employed to address the unique ore body characteristics. The best examples of this approach were dealing with the initial high clay content saprolite ore from the development phase and primary mining pits whilst ensuring that the design also implemented the right method to deal with the future fresh rock in an environmentally sensitive habitat. In order to do this separate individual crushing flowsheets were generated, focusing on the specific material handling equipment that would be suitable to handle these various types of material and ensure high recoveries were maintained.INTRODUCTIONAurora gold mine is located in forested region of Guyana, 170 km west of capital Georgetown, and 130 km West North-West of Bartica, a settlement at the junction of the Essequibo and Cuyuni Rivers.The Aurora gold project (Aurora) is a 5,000 tonne per day open-pit/underground operation, which will produce a total of 3.29 million oz. gold – averaging 194,000 oz. per year – over an initial 17 year mine life. At the final investment decision in 2014 Aurora had a total resource of 6.54 million ounces in the measured and indicated categories (62.83 million tonnes at 3.24 g/t Au) as well as additional 1.82 million ounces in the inferred category (16.93 million tonnes at 3.34 g/t Au)."

Jan 1, 2016