Search Documents

By M. Fujikawa

The Kamioka Zinc Smelter was converted from the jarosite process to the goethite process in the year 2000. The reasons for the conversion of the process were that the silica content of the raw material increased and the iron content decreased. The silica easily turns to a gel in sulfuric acid solutions and this causes the solid-liquid separation characteristics to deteriorate. The basic behavior of silica in sulfuric acid solution was investigated and it was found that the goethite process is the most suitable to effectively separate and remove silica from solution. Furthermore, Fe has the capability to remove elements such as Ge that have an adverse effect on zinc electrolysis. This means that, when the Fe content of the raw material decreased, the impurity removal capability also decreased and there was a risk of a build-up of impurities in the process. Iron precipitates in many forms in sulfuric acid solutions. The capability to remove elements such as Ge differs depending on the compound precipitated. Goethite has a higher capability than jarosite to remove elements such as Ge. In this report, the results of applying the process established by investigations of the basic behavior of Fe, silica and Ge in the zinc refining plant are presented.

Jan 1, 2006

By Alan Bauer, Melvin A. Cook

Measured detonation pressures of "prills and oil" (94/6 ammonium nitrate/fuel oil) and three of the new "slurry" blasting agents are presented and compared with computed, ideal detonation pressures and with detonation pressures expected from the measured detonation velocities. Results seem to show that the peak pressure in the detonation wave in these cases is the Chapman-Jouguet pressure and that no "spike" exists in these detonation waves. The absence of the Zeldovich-von Neumann "spike" is noteworthy in view of the very long reaction zone lengths of these mixtures. The measured detonation pressure of one of the slurry blasting agents (DBA-3") under steel confinement ( 172 kilobars) is shown to be considerably greater than the ideal detonation pressure of 75 per cent gelatin dynamite (p. = 135 kilobars) despite the fact that the detonation was still somewhat non-ideal in "DBA-3," its computed ideal detonation pressure being 180 kb. The popular 94/b AN /FO blasting agent exhibited a detonation pressure of only 13.5 kb in 5" paper tubes, but 37.5 kb in 5"• steel pipe compared with a computed ideal pressure of 40 kb.

Jan 1, 1961

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

By A. Bouchard

"Based on laboratory testwork, a two-stage cleaner / re-cleaner circuit with feed regrind was proposed to replace an existing single-stage middling circuit treating a scavenger concentrate at Inco’s Clarabelle mill. In order to effectively transfer the technology and implement the new flowsheet in the plant, an extensive on-site pilot plant campaign was conducted. After demonstrating the improved metallurgy, the two-stage middlings circuit was successfully implemented at the operation.The present paper describes the on-site pilot plant testwork and the plant metallurgical improvement after implementation of the new middlings circuit. The addition of TETA / Na2S03 greatly enhanced the pentlandite selectivity against pyrrhotite and the two-stage cleaning considerably improved the pentlandite selectivity against rock minerals. The improvement was immediate after the installation of the new middlings circuit. Size by size recovery analysis indicated that a finer regrind would further improve the metallurgy of the new two-stage cleanerhe-cleaner circuit and those modifications are in progress at the mill.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill has been described elsewhere (Kerr and Kipkie, 1985; Agar, 1991). While maximizing the recoveries of chalcopyrite (Cp) and pentlandite (Pn), continuous effort has been directed toward improving pyrrhotite (Po) and rock minerals (Rk) rejection. Inco discovered diethylene triamine (DETA) and triethylene triamine (TETA) (Marticorena, et al., 1994) for pyrrhotite rejection. Falconbridge further improved pyrrhotite rejection using DETA and SO2 (Kelebek, et al., 1995). No special technologies are used in the rejection of rock minerals."

Jan 1, 2001

By M. J. Michaud, M. J. Lavigne

"Abstract - North American Palladium Ltd. operates its Lac des Iles open pit palladium mine 85 km north of the city of Thunder Bay, Ontario. The Roby Zone deposit occurs within the mafic/ultramafic Lac des Iles Intrusive Complex (LDI-IC), which was created by multiple pulses of magma of varying composition within several closely spaced chambers. Chaotic lithological distribution, the presence of magmatic breccias, and the rarity of rhythmic layering suggest a dynamic intrusive environment with disruptive magma pulses. As of December 31, 2001, measured and indicated resources for the 950 m long by 815 m wide Roby Zone deposit totalled 159 Mt grading 1.55 g/t Pd, 0.17 g/t Pt, 0.12 g/t Au, 0.05% Cu, and 0.05% Ni at a palladium cut-off grade of 0.7 g/t. The Roby Zone contains an additional 73 Mt of inferred resources at similar grades.The Roby Zone is dominated by varitextured gabbro containing pipes and pods of breccia, and large blocks (~60 m across) of varying lithology. Mineralization at Lac des Iles occurs as: (1) a PGEand base metal-rich magmatic matrix of breccia (breccia ore); (2) mineralized dikes or sills (gabbronorite in North Roby ore); (3) lower-grade mineralization in varitextured units that are host to the distinctive breccia ore and envelope the North Roby ore; and (4) high-grade mineralization associated with strong silicate alteration exemplified by high-grade ore.The close spatial association of the mineralized breccias with both varitextured units and silicate alteration leads to an interpretation that the energetic magma that created breccia was charged with a dissolved fluid, and that this deuteric fluid exsolved at high temperatures to migrate through crystal mush, enhancing crystallization along its pathways, resulting in variable grain size. This transformation occurred at high temperature and produced sulfide-poor, varitextured gabbro-hosted mineralization exemplified by some of the mineralization in the North Roby Zone, and also found throughout the Roby Zone. The association of hydrous silicate alteration with mineralization can be explained by continuing fluid migration during cooling and continued metal transport. Résumé - North American Palladium Ltd. opère la mine à ciel ouvert de Lac des Iles située à 85 km au nord de Thunder Bay, Ontario. Le gisement Roby Zone est encaissé dans le complexe mafique/ultramafique de Lac des Iles (LDI-IC), lequel représente une intrusion polyphasée créée par plusieurs pulses magmatiques de différente composition à l’intérieur de chambres magmatiques fermés. La distribution chaotique des lithologies, la présence de brèches magmatiques, et la quasi-absence de litage rythmique suggèrent un environnement magmatique dynamique perturbé par l’introduction de nouveau magma. Au 31 décembre 2001, les ressources mesurées et indiquées s’élevaient à 159 millions de tonnes titrant 1,55 g/t Pd, 0,17 g/t Pt, 0,12 g/t Au, 0,05% Cu, et 0,05% Ni, pour une teneur de coupure de 0,7 g/t Pd. De plus, la Roby Zone contient 73 millions de tonnes de ressources inférées à une teneur similaire.La Roby Zone est principalement encaissée dans un gabbro de texture hétérogène (varitextured) caractérisé par des cheminées et des lentilles de brèches et des énormes blocs (environ 60 m de diamètre) de plusieurs lithologies. Au Lac des Iles, la minéralisation en EGP et en métaux de base se retrouve dans la matrice magmatique de brèches (breccia ore), dans des dykes ou des sills minéralisés (gabbronorite dans la zone North Roby ore), comme minerai de basse teneur encaissant le minerai de brèche (breccia ore) et enveloppant la zone North Roby. Du minerai de haute teneur est également associé avec une forte altération en silicates dans la zone high-grade ore.L’étroite association spatiale entre les brèches minéralisées et les unités de texture variée (varitextured) et l’altération en silicate suggère que le magma énergique qui a causé la bréchification était chargé de fluides. Ces fluides deutérique"

Jan 1, 2001

By Mohamad Kharseh

There is general acceptance that climate change, which is the most important challenge facing humanity, is anthropogenic and attributed to fossil fuel consumption. Therefore, improving the performance of our existing energy systems and deploy more renewable energy resources is an urgent issue to be addressed. Geothermal refers to existing of heat energy in deep rock and sedimentary basins. This energy can be used to drive a power turbine to generate electricity. Traditionally, geothermal has been exploited in places with the plentiful hot water at relatively shallow depth. In the light of fact that ground temperature increases with the depth everywhere on the Earth, engineered geothermal systems (EGS) can be installed in any place to exploit the geothermal in generating energy. Unfortunately, the high exploration and drilling costs of boreholes is the main barrier to commerciality of EGS worldwide. In addition, there are technical problems associated with drilling big depth. In oil producing countries such problems can be addressed by utilizing whether active or abandoned oil or gas wells and, consequently, EGS can produce power at profit. The current study presents an analysis of a binary geothermal power generation system for commercial electricity generation in Qatar. For this purpose, two binary cycles are assumed the main difference between them is that the first one is air cooled while the other will be water cooled. The performance of the two cycles and the possibility of improvement has been shown. Economic analysis the power plant shows that the levelized costs of electricity is 3.6US¢/kWh and the pay-back time is less than 8 years.

Aug 1, 2013

By S. Maleksaeedi

On-site evaluation of strength using hardness is common for different materials. The lack of such relation for aluminum alloys has always been felt. In this work, a finite element analysis of plastic deformation and its distribution in Brinell hardness testing is presented. The analysis has been performed for different strength levels of aluminum alloys. By utilizing the Von Mises equivalent strain in hardness, it is tried to derive a correlation between hardness and strength values for the alloys under consideration. The derived correlation is verified using the experimental values available in literature.

Jan 1, 2004

By Haofeng Xie, Lijun Peng, Xujun Mi, Xue Feng, Xiangqian Yin, Zhen Yang, Guojie Huang

The Cu/Al composite wires have been widely used in cable industry. Especially in the development of aerospace, the light weight character of wires is particularly important. The wires are fabricated by a drawing process and heat treatment. Mechanical and electrical properties are measured and analyzed. The bending behavior is studied by scanning electron microscope. INTRODUCTION Cu/Al composite is a typical bimetallic composite that has been used in plenty of fields such as automobile and aerospace. The composite has the advantages of excellent conductivity as well as low weight, which cannot be obtained from single copper or aluminum. Industrial products of Cu/Al composite include Cu/Al composite joints (Uscinowicz, R., 2013), Cu/Al bimetallic sheets (Li, X. et al., 2011), Cu/Al flat bar (Wu, Y. & Liu, X. & Xie, J., 2014) and CCA wires (Ahmed N., 1978). CCA wires refer to the composite wires that copper layer concentrically coated on the surface of aluminum core conductor, implementing solid combination of two metals on the interface and forming an integral. At present, the aircraft cable generally use copper or copper alloy conductor, which makes the wire in the aircraft occupy a considerable proportion due to the large density of copper. Therefore, the use of Cu/Al composite wires instead of copper wires for weight loss, is of great significance to the development of aerospace technology industry. Heat treatment is an indispensable procedure to improve plasticity during cold working process, which is of great importance to preparation of wires (Wang, Q. et al., 2008). During the heat treatment, the Intermetallic Compounds (IMCs) are inevitable formed at the contact area of Cu/Al due to the occurrence of diffusion (Lee, S. et al., 2012). According to the results of former researchers, kinds of IMCs were discovered. Antoine Gueydan (2014) identified the formation of three IMCs (Al2Cu, AlCu, and Al4Cu9) at the interface between copper and aluminum after thermal aging. IMCs have a significant effect to the properties of Cu/Al wires. Bending performance is a vital property for the actual application of wires. The brittle IMCs may create a stress concentration that can cause crack initiation during bending process. This work focus on the mechanical properties of Cu/Al composite wires after heat treatment. The effect of various annealing condition on mechanical and electrical properties are studied, in order to find the appropriate annealing conditions, which produce optimal combination properties of Cu/Al clad composite wires. Bending fracture of composite wires is discussed by morphology observation.

Jan 1, 2019

By Saikat Chatterjee, Xintong (Brett) Liu, Kinnor Chattopadhyay

Magnesia carbon bricks are commonly used in BOFs and are generally pre-heated before the BOF goes into service. Owing to very stringent emission regulations, the BOF pre-heating process need to be controlled and optimized so that, the emission standards are met. One of the major concerns in organic emissions are its stringent limits on emission rates and total volatile emissions. In the present work, an attempt has been made to integrate CFD and Thermodynamic models to predict the emission rate of volatile organics during the pre-heating process. A one dimensional heat transfer model was developed using visual basic and then integrated with thermodynamics calculations using FactSage 6.4. The parameters that affected organic emissions were the pre heating procedure, gas composition of the burner, heating rate and type of the burner. Typical composition of MgO-C bricks and binder materials were obtained from literature and vendor data sheets. Chemical reactions between organic materials, refractory and burner gasses were considered. The model predictions indicated that certain burner conditions could destroy all organics before it exits the vessel while other conditions needed the use of an after burner at the mouth of the vessel. The model was also able to predict the organic emission rates based on the chosen pre-heating profile. This kind of predictive model will be very useful for the steel industry and enable them to justify permit limit applications and stick to the limits by fine tuning their pre-heating process.

Jan 1, 2015

By Jean Dugas, Roger Sirois

The Mineral Deposits Service of the Quebec Department of Natural Resources is engaged in the preparation of metallogenic maps as a contribution to the Canadian Sub-Committee of the Metallogenic Map of North America. The preliminary work is being done on large-scale maps. The main objective is to clearly represent information on ore deposits in a suggestive way. The design of the legend to meet these requirements is discussed. As these maps are still only descriptive, a further step will be the interpretation of data into metallogenic maps with Jess emphasis on the individual deposits and more on the metallogenic factors. Both types of map should prove useful in the search for ore deposits; the first by providing at once a large amount of information, the second by suggesting the ore controls.

Jan 1, 1967

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By M. Jackson, R. McDonald, T. Osken, D. Robinson

"The addition of sulphidic materials in the leaching of nickel laterites has several potential benefits that include improvements in the rheological behaviour of the blends, reductions in the sulphuric acid and steam requirements, sweetening of the nickel grade of the combined feed material, and the option of using a range of sulphidic materials. The current study examines the oxidative processing of 30% w/w blends of nickel concentrate and nickel laterite ore at 250oC. In particular, the viability of using low oxygen overpressures was examined for significant amounts of nickel flotation concentrate, up to 12% w/w. Further to this the impact of process water quality, in particular the presence of chloride, upon the kinetics of extraction and the mineralogy of the residue were also investigated. This paper will present the results of preliminary work in this area.INTRODUCTIONThe use of sulphidic ore as a source of sulphuric acid during oxidative hydrometallurgical processing is not a novel idea and can be traced back over forty years (Seidel & Fitzhugh, 1968). A series of patents pertaining to application of this approach for laterite ores can be subsequently found (O’Neill, 1973; Opratko et al., 1974; Rodriguez, 2008a, 2008b; O’Callaghan, 2010; Liu et al., 2011) and a few of articles containing published data (Ferron & Fleming, 2004; Quinn et al., 2009). The use of pyrrhotite tailings as a source of sulphuric acid has also been employed for the leaching of converter slags (Perederiy et al., 2011).It is known that hydrometallurgical operations such as the HPAL plant at Murrin Murrin have added small amounts of sulphides as either transitional (mixed sulphide/oxide) ore or non-smeltable concentrate. This can improve the rheology (Rodriguez, 2009) and provide heat credits. However these plants are generally limited in their ability to add such materials due to their reducing nature and given under highly acidic conditions that the breakdown potential of the titanium used for the autoclave lining is significantly reduced. A suitable oxidant must therefore be present to ensure the potential remains sufficiently high."

Jan 1, 2012

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

The Shortage of Mining and Metallurgical Engineers I N many parts of the Western World attention has recently been drawn to the acute shortage of mining and metallurgical engineers produced by the universities. Naturally, the reasons for this shortage have been discussed, and various remedies for it have been proposed. In this paper, I want to examine some of them. It is now fairly generally ac-cepted among mining men that the easy attractions of modern urban life have left the career of mining in the metaphorical as well as in the literal backwoods. The industry finds it increasingly difficult to recruit adventurous and intelligent young men; for such men now seek their intellectual, if not physical, adventure in more glamorous occupations from a safe social base in suburbia. The salaries, opportunities and security offered by the mining industry do not complete effectively with the rewards offered by other industries and by commerce, taking into account the social disadvantages of a mining life. The excitement and other non-material attractions of mining

Jan 1, 1965

By Michael Magerstädt

Material loss by abrasion of contact surfaces of pipes, chutes, pumps, and other equipment in contact with ore is one of the main reasons for downtime of mining operations. Abrasion protection materials in use range from expensive tungsten carbide overlay to hardened steels, ceramics, as well as polymers, particularly polyurethanes (PUR). This paper describes abrasion protection products made from High Performance Polyurethane Elastomers. An interior pipe coating was developed that exhibited outstanding abrasion resistance and an extremely high adhesion to steel. Years of field testing in oil sands tailings as well as applications in slurry lines (e.g., phosphate slurries) have proven the performance of this material. A proprietary field joining process was developed and successfully applied in the field. This joining process requires only one field weld per joint very similar to the joining of uncoated pipe. No internal re-coating is necessary adding savings during pipe laying to the significant savings of reduced down time. Using the building-kit chemistry of polyurethane synthesis, similar high performance elastomers were used to extend the life time of ball mills. An intelligent system was developed in which wear parts contain sensors reporting the actual wear thereby optimizing maintenance interval leading to significant cost savings for the operator. Test data as well as field experience with High Performance PUR Elastomers for abrasion protection in mining are presented.

Aug 1, 2013

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By G. T. Lapidus, J. Trejo-Gallardo

A phenomenological model is presented for leaching silver from silver sulfide contained in mineral particles with ammoniacal thiosulfate solutions of copper in stirred reactors. Experimental results were used to adjust the kinetic parameters of the model, such as the reaction order and velocity. The incorporation of the cuprous sulfide-silver sulfide equilibrium at the reaction interface allowed the prediction of the conversion limits for different reagent concentrations. The information obtained from the reactor model was later integrated into a heap leaching simulation, whose results adequately describe tendencies observed in column tests, with respect to variations in copper and thiosulfate concentrations. Comp

Jan 1, 2005