Search Documents

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By T. G. Joseph

The chicken and egg scenario where adverse truck motions cause ground deterioration and poor ground profiles that in turn cause adverse truck motions is a downward deterioration spiral that dominates in our industry. If we can remove one action, the reaction must stop and vice-versa. A simple 'truck to excavator' load data analysis and wireless communication system is outlined in this paper; that will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. In turn this will reduce the subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life and ongoing maintenance of haul roads

Nov 1, 2011

By David J. Morrison

Scarcity of truck tyres, increasing cost and decreasing availability of labour, increases in fuel costs and project budget blowouts have changed the paradigm behind mining equipment selections. The cycle of commodity changes have occurred in parallel with the increasing maturity of continuous mining machinery, mobile in-pit crushing systems and very large scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

May 1, 2007

By T. T. Chen

The iron- and elemental sulphur-rich residues generated during batch and continuous pressure oxidative leaching of Inco Limited's Voisey's Bay nickel sulphide concentrate at 150°C in sulphate-chloride media have been characterized by X-ray diffraction analysis and scanning electron microscopy. The residues produced during the continuous leaching of the pentlandite- and pyrrhotite-rich concentrate consisted predominantly of hematite and elemental sulphur, with minor amounts of goethite. Although the iron species generated in the batch leaching tests were similar to those formed during continuous leaching, the morphologies of the hematite and goethite particles were significantly different. In addition to the tiny spheroids and bubble-like particles, the hematite and goethite generated during batch leaching occurred as larger "hollow" shell-like particles that contained residual pentlandite or sulphur cores. Although the leach solution from which the iron oxides had precipitated contained 5-15 g/L sodium, sodium jarosite was detected only in trace amounts in a few of the leach residues.

Jan 1, 2006

By F. M. Waldie

THE 2,538-foot belt conveyor recently installed underground at the Sullivan mine hoists ore from the 3,350-foot level to the 3,900-foot or main haulage level, a vertical distance of 680 feet. The design and planning of development work, under the direction of Mr. R. H. Stewart, Consulting Engineer, was begun in the spring of 1941. Development work was started in July of that year from the 3,350-foot level, and headings were started on the 3,650-foot and 3,900-foot levels later in the same year. It was the intention at that time to keep three headings going on development work necessary for the installation of the system: two on the conveyor incline, and one on the 3,900-foot level. This programme was modified in 1942 when there was some doubt whether the material for construction could be obtained. This problem of supply was eventually solved and the development work was pushed to completion in December, 1943. Construction was started in December, 1943, "'under the supervision of Mr. G. H. McKay, Superintendent of Construction and? Maintenance, and was completed in November, 1944.

Jan 1, 1945

By J. Reinhardt, R. Uken, S. S. Chinnasamy

Au mineralization in the Kilpwal Gold Mine is confined to laminated quartz-carbonate lodes and associated alteration along the Klipwal Shear Zone (KSZ) in the upper Mozaan Group of the Mesoarchaean Pongola Supergroup. The brittle-ductile shear zone is characterized by inner and proximal hydrothermal alteration domains that are comprised of chlorite, epidote, sericite, pyrite, arsenopyrite and gold. Possible sources of gold are: (i) paleo-placer U-Au rich conglomerates from the lower Mozaan Group; (ii) the underlying mafic volcanics of the Nsuze Group; (iii) greenstone belts in the basement to the Pongola basin. Post-Pongola granites probably provided the heat to mobilize auriferous fluids into the KSZ.

Jan 1, 2011

By W. A. Jankola, M. T. Martin

"The world's first zinc pressure leaching plant at Cominco's Trail operations started production in 1981. Sullivan zinc concentrate is leached at the rate of 190 tpd in a four-compartment autoclave at elevated temperatures and oxygen pressures to produce a zinc sulphate solution and elemental sulphur. Zinc extraction exceeds 98% and sulphide to elemental sulphur conversion exceeds 95%.The sulphur is recovered from the discharged slurry in the underflow of a hydrocyclone, and is upgraded as a flotation concentrate. The concentrate is dewatered, melted and filtered to produce a polished sulphur product of better than 99% purity. An alternative sulphur recovery process employs an unique sulphur separation method that recovers over 90% of the sulphur in the molten state. The remaining sulphur is recovered by flotation following flash discharge of the slurry. The product slurry containing the zinc sulphate solution and the iron-lead residue joins the existing roast-leach zinc plant for purification and zinc electrowinning.IntroductionIn 1981, Cominco Ltd. commissioned the world's first commercial zinc pressure leaching plant at their Trail operations in British Columbia. As part of a $700 million modernization and expansion program for lead and zinc started in 1977, the company installed the first o f two autoclave trains.Prior to pressure leaching, zinc production was closely tied to acid and fertilizer production. Sulphur dioxide produced from roasting the concentrates had to be converted to sulphuric acid. Thus, any expansion of zinc operations with the roast-leach technology would have required extensive modifications to the acid and fertilizer plants as well as to the roasters. Zinc pressure leaching, on the other hand, offered a one-step dissolution of zinc from the concentrates with high extraction, and production of elemental sulphur. The associated dust and sulphur dioxide generated in the roasting process are both eliminated from the working environment of the pressure leach facility. The flexibility allowed by producing elemental sulphur, and the opportunity to break the sulphuric acid link for about 25 per cent of the targeted 272,000 tonnes per year zinc production was very appealing. The process was successfully demonstrated at a pilot plant in 1977(1-6)."

Jan 1, 1985

By Horatio Sam-Aggrey, Margot Hurlbert

Small Modular Reactors (SMRs) have been touted as having the potential to spearhead a nuclear renaissance. Proponents of this view cite the relative advantages of SMRs over larger nuclear plants as reason for their optimism. Some of these merits include potential economies of mass production deriving from modular factory production, enhanced safety features, the ability to locate reactors in remote areas, and reduced requirements for technical workforces to install and maintain SMRs. Despite the optimism surrounding SMRs, nuclear power is still a contentious issue for many Canadians. The growth of nuclear power remains adversely affected by concerns over issues such as: the health and safety consequences of nuclear power generation, environmental impacts, proliferation of nuclear materials, terrorism, and radioactive waste disposal (Organisation for Economic Co-operation and Development (OECD) and Nuclear Energy Agency (NEA), 2010). Personal values, past nuclear accidents, and lack of trust in the industry are other factors influencing attitudes toward nuclear energy (IAEA, 2005). In Canada, three main areas where SMRs could be used have been identified. These include: a. Traditional, on-grid power generation, especially in provinces looking for zero-emissions replacements for CO2-emitting coal plants. B. Remote off grid communities that currently rely on diesel or fuel oil power generation. There are 279 off-grid communities in Canada, many of them being Aboriginal communities (NRCan, ND). Notably, all communities in each of Canada’s three territories qualify as remote. C. Resource extraction sites, such as mining and oil and gas extraction sites. Many of Canada’s principal producing mines and active mineral exploration projects are located within close proximity of Aboriginal communities. Any proposed implementation of small nuclear plants would, require the support of the local population, which is largely Indigenous in the northern regions. The possible deployment of SMRs raises important issue relating to consultation and accommodation of Aboriginal concerns regarding potential SMR deployment. This is especially pertinent given Canada’s pending implementation of the provisions of UNDRIP. One of the provisions of UNDRIP that has attracted a lot of attention is the one on Free Prior and Informed Consent (FPIC). Drawing on previously published information, this paper discusses some of the challenges posed by FPIC for the deployment of SMRs. The next section outlines the provisions of FPIC and its implementation in the Canadian context. Section 3, details some of the challenges posed by FPIC to the deployment of SMRs, while Section 4 provides some concluding comments.

Jan 1, 2020

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By E. Barsky

"Theoretical notions of mass transfer processes in cascade separation of bulk materials have not been adequately developed as yet (Barsky M.D. 1980). In this paper we have derived linear difference equation of the second order for a cascade with initial feeding top any stage proceeding from mass exchange regularities. The solution of these equations has allowed us to determine quantitative dependences of the material distribution over the cascade stages, which serve the basis of the method of predictive estimate of the process results. We have also examined the model of the material distribution coefficient formation at individual cascade stages.We have checked the adequacy of this model to experimental data. It is noteworthy that the obtained theoretical results are phenomenological, i.e. they can be applied to the processes of separation of different physical nature, e.g. of isotopes, liquid media, gases, etc.INTRODUCTIONRecently, the processes of cascade separation of bulk materials have found broad application in various industries. They ensure a high separation efficiency and high-quality composition of final products. Although specialized literature gives serious attention to cascade processes [1], their theory is not sufficiently developed yet. To achieve optimal organization of this process, we examine mass transfer in a cascade gravitational classifier with stages of identical design."

Jan 1, 2016

By Vincent Jourdain

Located in the James Bay Territory of Quebec (figure 1), the Clearwater property is jointly owned by SOQUEM Inc. and Eastmain Resources Inc. Exploration on the property since the early 70's has resulted in the discovery of several gold showings. Exploration work by the joint venture since 1995 has led to the definition of the Eau Claire Zone containing an indicated resource of 540 000 tonnes grading 11.1 g/t Au (8.7 g/t Au cut at 34.28 g/t Au). Hosted by the archean Eastmain Greenstone Belt, the property geology is dominated by mafic volcanics containing thin horizons of felsic volcanics and/or sedimentary rocks (figure 2). The sequence is metamorphosed to the amphibolite facies and contains two small toalitic intrusions. Regionally, the structural trend is oriented E-W but in the area of the Eau Claire Zone a second trend oriented NE-SW is also present. The first exploration work on the property was conducted by SEREM and SDBJ from 1973 to 1976. It consisted of an airborne electromagnetic survey and a ground follow-up program on several grids. This program, comprising geological mapping, geophysics and drilling, led to the discovery of the Natel showing where a drill intersection returned 8.89 g/t Au over 2.65 m. From 1978 to 1985 the area was withdrawn from staking because of the hydroelectric projects of the James Bay. In 1985, Westmin Resources Limited and Eastmain Resources began an exploration program based on a helicopterborne electromagnetic survey. Once again, a ground follow-up program was conducted on several grids. This program included a soil geochemical survey that identified a strong (up to 10 g/t) gold anomaly. Drilling of the anomaly led to the discovery of the Eau Claire Zone where resources were estimated at 270 000 tonnes grading 6.1 g/t Au at the end of 1990. In 1995, SOQUEM Inc. took an option to gain a 50% interest on the property and obtained its interest in 1998. Since 1995, two principal mineralization zones were identified on the property. The "Rosemary Zone" consists of veinlets and disseminations of pyrite and chalcopyrite within a magnetite-rich amphibolite. The mineralized zone was identified by stripping within an area of 1000 by 500 metres. Drilling indicates copper grades up to 0.32 % Cu over 49.2 m. with locally grades of 0.75 % Cu over 5.9 m. The mineralised zone is associated with QFP dykes and corresponds to a strong magnetic anomaly and a strong copper and molybdenum soil anomaly. The "Eau Claire Zone" consists principally of a set of gold bearing quartz-tourmaline veins oriented E-W and dipping at 45-50??to the south (figure 3). More than ten different veins are recognised in the zone and up to eight veins were observed in a single trench (figure 4). The host rock between the veins shows a degree of deformation similar to the regional volcanosedimentary rocks. Each vein is hosted by a unit of actinolite-tourmaline-biotite schist up to one meter thick. The veins and their hosting schist clearly cross-cut the schistosity of the hosting lithologies and the contacts between amphibolites and felsic to intermediate rocks. Usually, the veins are less than a meter thick and are composed of quartz, tourmaline and calcite. The proportion of quartz and tourmaline varies from 0 to 80% within a single vein. The veins commonly show massive, banded or brecciated texture. Sulphides, mainly pyrite, pyrrhotite and chalcopyrite, generally form less than 5% of the vein material.

May 1, 2001

By J B. Maughan

Gas and oil seeps have been known in Quebec for more than one hundred years. These occur in three main areas which contain sedimentary rocks with a total thickness estimated to vary from 6,000 to 20,000 feet. The strata in these areas are similar in many respects to those in producing areas of southwestern Ontario and the Appalachian basin, and the prospects for finding and developing commercial reserves of oil and gas in Quebec would therefore also appear to be favourable. Little of the exploratory drilling to date has been con-ducted in a systematic manner, and most of the drilling has utilized improper or inadequate equipment. Many wells have also failed to adequately test and fully evaluate the principal zones of interest. Relatively high drilling costs have hindered systematic exploration; however, with improved portable equipment, it is expected that future wells can be drilled with greater efficiency and at less cost. Most of the mineral rights in Quebec are held by the Provincial Government, and acreage can still be leased in large blocks on favourable terms.

Jan 1, 1964

By G. A. Peebles

"This paper describes the various types of radiometric instruments and the techniques of their operation for grade control, sampling, assaying and probing drill holes at Eldorado Nuclear's uranium mine in northern Saskatchewan. Modifications that have been made to these instruments are discussed, and suggestions are made for the development of more refined and specialized radiometric equipment."

Jan 1, 1969

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe."

Jan 1, 2017

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012