Search Documents

By A. M. Cameron

THE HOISTING PLANT at the Stobie section of the FroodStobie mine is a two-shaft installation designed to handle a daily production of 18,000 tons of ore at depth. The two vertical shafts are within 100 feet of -each other, an arrangement made to provide the needed capacity and to give flexibility of operation (Figure 1). No. 7 shaft, used for handling men and supplies as well as for hoisting ore, has been sunk to the 3000 level and is served by a manhoist handling two cages and an orehoist with two 14-ton capacity Kimberley skips. No. 8 shaft, so far completed to a depth of 1,900 feet, handles only ore. The hoist is semiautomatic with push-button control and the skips are 15-ton capacity bottom-dump. The ore-loading pocket for first stage hoisting at both shafts is 120 feet below 1,600 lev-el and additional pockets are planned, as the shafts are deepened, at 800 foot intervals down to 4,000 feet.

Jan 1, 1956

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

By Steve Scott

Outline of Talk Seafloor Massive Sulfides (SMS) and Seafloor Sedimentary Sulfides (SSS) Ocean mining of SMS (Nautilus Minerals) Environmental issues Summary

May 1, 2013

By M. A. Marois

This paper proposes an improved temporal stability condition for the implementation of an inverse heat transfer method for predicting the time-varying bank thickness of the phase change protective bank inside a high temperature furnace. The direct problem is handled with the enthalpy method. The inverse method rests on the Adjoint Problem and the Conjugate Gradient Method. It is shown that the temporal stability condition for the inverse phase change problem relies on the time delay of the temperature measurements. Results indicate that this time delay is proportional to the heat diffusion time including heat diffusion through the mushy zone.

Jan 1, 2011

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By Yu Chen, Charlie C. Li

The application of rock bolts for the stabilisation of underground openings needs a good understanding of the response of the bolts during rock excavation. The pull-and-shear performance of two types of rock bolts—that is, the fully encapsulated rebar and the D-Bolt—has been studied both experimentally and numerically. The rock bolts were tested under a pull-and-shear load at five displacing angles (i.e., 0°, 20°, 40°, 60°, and 90°), and at the same time, the strains on the bolts were monitored during testing. The two types of rock bolts have similar loading capacities, while the loading angle has obvious influence on the deformation capacity of the D-Bolt. The ultimate total displacement of the D-Bolt decreases from 140 mm under pure pull loading to 70 mm under shearing. The displacement capacity of the rebar is not significantly influenced by the loading angle but remains at a quite low level from 29 to 53 mm. The D-Bolt yielded in a longer section the rebar bolt under pure shear. A trilinear material model was used to simulate the strain hardening behaviour of the bolt steels in the numerical code FLAC3D. The numerical results show that the axial load in the bolt decreases exponentially with the distance from the loading position for the rebar bolts, but it remains constant in the bolt sections between the anchor positions for the D-Bolts. When the bolt is subjected to a lateral load, shear stresses are created on the D-Bolt surface within a short distance from the loading position.

Jan 1, 2015

By B. I. Boyko

As part of the Ministry of the Environment's Resource Recovery Program, the Province of Ontario has constructed a $13 million "Experimental Plant for Resource Recovery" in Metropolitan Toronto. The technology and unit operations involved in the processing of municipal solid wastes at a rate of 40 tons per hour at this facility are reviewed. Shredding, air separation and classification, screening, magnetic separation and composting are some of the operations featured at this plant. Recoverable commodities expected include paper, ferrous metals, an air-classified light fraction (shredded paper and film plastic), glass and compost. Existing and potential markets for these materials are discussed.

Jan 1, 1978

Forward-Looking Statements Information set forth in this presentation may involve forward-looking statements under applicable securities laws. Forward looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. Forward-looking statements or information relate to, among other things expected iron ore demand, timing for a production decision, expected share price drivers, potential railway options, timing, grade and quantity of potential resource estimates, employment and economic benefits, taxation estimates and timing of key project milestones. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause our actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the following risks: the risks associated with the need for additional financing; operational risks associated with exploration; fluctuations in commodity prices; title matters; environmental liability claims and insurance; reliance on key personnel and other risks and uncertainties discussed in the management discussion and analysis section of our interim and most recent annual financial statement or other reports and filings with the TSX Venture Exchange and applicable Canadian securities regulations. Forward-looking statements are made based on management's beliefs, estimates and opinions on the date that statements are made and the Company undertakes no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by law. Investors are cautioned against attributing undue certainty to forward-looking statements. NI 43-101 Qualified Person Alderon?s exploration work on the Kami Project is supervised by Edward Lyons, P.Geo., the Chief Geologist for Alderon and a Qualified Person as defined byNational Instrument 43-101. Mr. Lyons has reviewed and is responsible for the technical information contained in this presentation. Mr. Lyons is a member in good standing of the Association of Professional Engineers and Geoscientists of British Columbia (APEGBC) and the Professional Engineers & Geoscientists Newfoundland & Labrador (PEGNL) as a registered Professional Geoscientist (P.Geo.).

May 1, 2011

By G. G. Richards, D. J. Rioux, R. L. Stephens

Teck Cominco Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. The year 2007 marks ten years of operation of KIVCETTM flash smelting technology for the treatment of zinc plant residues and lead concentrates. Since start-up in 1997, the furnace throughput has been increased to exceed its design rate and other metallurgical performance targets while continuing to meet its environmental objectives. This was achieved through resolution of key mechanical issues, improved understanding to stabilize the reaction shaft operation and control furnace accretions, significantly reduced boiler corrosion by molten chloride salts through the extensive application of weld overlay, a suite of projects to improve furnace integrity, and some debottlenecking of the surrounding unit operations in the lead smelter. The combination of increased feed rate and improved on-line time allowed the KIVCETTM furnace to set a new quarterly feed throughput record of 129,300 tonnes in the first quarter of 2008.

Jan 1, 2008

By J. Basi, J. A. Finch

ABSTRACT Testing the effects of bubble size (Db) in a Mo cleaning ?otation column at Highland Valley Copper mine indicated that increasing the proportion of small (< 1 mm) bubbles signi?cantly improved column metallurgical response, compared to typical operation. The results were a three- to four-fold Mo recovery increase and a 1 to 2% Mo (absolute) concentrate grade increase. The improvedcolumn operation produced a 4% Mo plant recovery increase. This study also showed that modelling the ?otation rate constant (k) as an inverse square function of Db was more accurate than considering k to be inversely proportional to Db.

Jan 1, 2010

By C. A. Young, H-H. Huang, L. G. Twidwell

Solid particles, especially oxides/hydroxides, develop an electrical charge on their surface when submerged in aqueous solution. Parks was able to relate PZC (point of zero charge) of an oxide to its minimum solubility and isoelectric point. Dzombak has compiled an extensive database for adsorption reactions on ferrihydrite surfaces using the double layer theory. The equilibrium calculational program, STABCAL has been used to extend the considerations of Parks and Stumm. The PZC for many hydroxides, complex oxides, and non-oxides have been investigated and the results are reported in the literature. Removal of arsenic and metals by adsorption on ferrihydrite as the substrate has been computed using ST ABCAL and the computational results are compared to experimental data. Absorbents other than ferrihydrite such as aluminum hydroxide are also discussed.

Jan 1, 2005

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

By Dr. Ralph W. Edie

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By C. Gordon Saunders

"The ungraded-fibre mill is located at the mine site and has a rated capacity of 6,600 tons of ore input and 1,200 tons of ung1•aded fib1 •e product per day. Power for operation is obtained from a diesel generating plant located on the site, which has a capacity of 5,300 kW. The preliminary milling process consists of prima1•y and secondary crushing, drying and temporary storage of plus-1 1h -in. material. The final milling processes are two stages of crushing and three stages of screening, with air-lift separation of the fibre from the host rock. The central mill building also houses a machine shop, mill maintenance shops, a mobile equipment overhaul shop, an engine and majo1•-component overhaul shop, and a warehouse. Major changes to the milling ci1•cuits since start-up have been the addition of a larger secondary cone crusher, ct third dryer, adding a rotary distributor to the feed of the screening section and adding an automatic start-up sequence for all equipment except crushers and fans. The operation of the mill is coordinated from a central control room, where a ""mimic"" panel indicates the operation of all major units in both the ore preparation and the screening sections. Product quality is controlled by continuous sampling and frequent labo1•atory analysis, which provide data fm• the adjustment of aspirating hoods and mill feed rate. Operating problems unique to this location, and common to a sub-arctic environment, are discussed."

Jan 1, 1976

By B. R. Conard

Copper refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because Cu and Ni carry risks for adverse health endpoints through inhalation exposure, it is critical that their aerosol levels, and the metallurgical processes through which they enter the air, are understood. Because certain Ni substances have been linked to respiratory cancers, it is also important to characterize the amounts and types of Ni compounds in occupational settings. This paper describes electrorefining and electrowinning operations near Sudbury, Ontario (1930–present), and gives aerosol measurements (1978–present).

Jan 1, 2014

By G. W. Norval, V. G. Papangelakis, G. A. Moldoveanu

Smelting has been the primary method of treatment for refractory copper sulfide concentrates such as enargite (Cu3AsS4), but the pyrometallurgical processing generates elevated levels of volatile arsenic. The present research investigates a novel hydrometallurgical process of oxidative dissolution of enargite at ambient conditions in the presence of chlorine dioxide (ClO2), a very powerful oxidant generated in solution by the reaction between a strong acid (HCl or H2SO4) and sodium chlorite (NaClO2). The effects of initial oxidant concentration, particle size, agitation speed and temperature on dissolution kinetics and copper extraction were investigated. It was found that a stoichiometric ratio of ClO2:Cu3AsS4 = 9:1 were needed to completely and congruently dissolve the mineral with fast kinetics (<15 minutes) under ambient temperature. The dissolution extent (metal extraction) increases with increasing ClO2 concentration and decreasing particle size of solids, but is not influenced by temperature or agitation speed.

Jan 1, 2014

By J. T. Vehkala, S. S. Kerr, D. E. Robertson

"Since the late 1970s, extensive work has been carried out at Placer Dome Inc. &apos;s Dome Mine to develop new mining methods and equipment to improve the productivity of narrow vein mining (Mining Magazine, Oct. 1986, pp. 308-317; Mar. 1988, pp. 176-/79). This work has been focused on mining veintype deposits varying from 0.9 m to 1.5 m in width using open stoping and cut-and-fill mining methods.In 1989, the Dome Mine entered into a contract with Ram Raising Ltd., a joint venture company of Angus Martin and I.S. Redpath Ltd., to develop and mine a narrow vein test stope using an Alimak Raise Climber. Early results have been favourable, indicating that Alimak methods can be used successfully to mine narrow vein are.HistoryThe Dome Mine, which has been in continuous operation since 1910, is located in South Porcupine, part of the city of Timmins, Ontario. The mine is wholly-owned and operated by Placer Dome Inc. and is part of Placer Dome Inc.&apos;s international stable of of 19 mines."

Jan 1, 1990

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946