Search Documents

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

"One of the corporate values mentioned by many companies deals with respect for people. This paper discusses one aspect of this value, namely, the need for clarity of accountabilities and authorities. The job of the manager in achieving this goal is analyzed and the benefits of enhancing the manager-employee conversation outlined. IntroductionCorporate values usually refer to the standards of behaviour that the leaders of the organization expect of all employees, including themselves, in carrying out their duties. Terms such as integrity, respect for the individual, continuous improvement, continuous learning, teamwork, speed, and innovation are quite common. The company-specific values are typically developed by the top executives of the company, and then tested with a broader group of employees. Where the process works, employees have a good understanding of what behaviour is expected of them in doing their work, in making difficult decisions, and in interacting with others.Having spent considerable time in his career investigating and studying the management systems at over 50 of the most successful companies in Canada, the United States, Europe and Japan, the author has had the opportunity to visit organizations such as Hewlett-Packard, 3M, Xerox, Intel, Toyota, NEC, Komatsu, British Airways, and Eastman Chemical. These experiences, together with the work of many other researchers, including the work of Dr. Elliott Jacques, have helped significantly to form the thoughts expressed below.Rather than reviewing the creation of corporate values and their deployment through the organization, these remarks focus on issues over which managers and employees have some control. The value in which managers can have significant impact deals with people and the respect shown them in the workplace. The component of respect to be emphasized is to be clear about expectations or accountabilities for oneself and the people who report to you, and to ensure that personal authority matches those expectations."

Jan 1, 1999

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

By P .. H. Grimley, N. Champigny

"Fourteen companies (Appendix) representing senior mining organizations in Canada were canvassed in order to assess: (1) the current usage and trends, and (2) the usefulness of computer applications in ore reserve estimation and grade control. The results of the questionnaire suggest that:• computers are unsurprisingly, predominant in the mining industry for calculating reserves and performing grade control;• time and cost savings are realized;• computer-based approaches are applicable to underground situations;• geological information is incorporated to the computerization process; and• computer usage does not hinder the collaboration of geologist and mining engineer.A clear need is identified for case histories comparing computer-calculated ore reserves and actual production data.IntroductionAmong the management and technical staff of some mining companies there is a perception that the application of computer based technology for the estimation of ore reserves and grade control, has as many drawbacks as benefits. Some of the objections raised against the utilization of computers for ore reserve estimation are that:• computer-based reserve models work for large open pit mines but not for underground situations;• computer-generated reserves ignore the geologist's knowledge base; they are strictly a number crunching exercise; and• the use of computers for ore reserves hinders collaboration between the geologist and mining engineer.In order to determine (I) the extent of current computer usage and future trends and (2) whether the objections noted above are borne out by experience, a number of senior Canadian mining companies were canvassed.The respondents were asked to provide:• an assessment of the importance of the computer in the ore reserve estimation and grade control process;• the level of involvement of individuals and staff groups with computer-based ore reserve estimation;• the advantages perceived and realized from the utilization of computer-based ore reserve approaches;• the current and future human resources requirements for the evaluation, implementation, maintenance and development of computer-based ore reserve systems;• the hardware and software resources presently used and planned; and• the developments needed to increase the use and acceptance of computer-based ore reserves."

Jan 1, 1990

By Ralph W. Edie

"IntroductionTHIS PAPER deals with chemical and mineralogical changes in wall-rocks associated with pitchblende mineralization in the Gold-fields area of Saskatchewan. The localities at which the rock specimens studied were collected, and descriptions of the various rock-types referred to, are given in a previous paper by the author (5).The geological field work upon which this paper is based was carried out while the writer was employed by the Eldorado Mining and Refining Company during the summers of 1948, 1949 and 1950. The laboratory work§ consisted largely of quantitative spectrographic analyses for both major and minor elements, supplemented by an examination of 250 thin sections of both altered and unaltered rocks.Character of the AlterationHydrothermal alteration, with associated pitchbende mineralization, is widespread in the Goldfields area of Saskatchewan. The most intense alteration is restricted to the immediate vicinity of fault or breccia zones, but large areas are affected to a minor extent.In detail, the relationship between alteration and pitchblende mineralization is complex, as individual veins do not in general have separate alteration halos. Pitchblende generally occurs in gash-like calcite veins or stringers in wide, fractured zones associated with faulting. Large, lenticular and tabular masses of slightly to intensely altered rock occur in the same wide fracture zones as the mineralized veins. However, vein deposition appears to be-long to a later fracturing period, after hydrothermal alteration was more or: less completed. Generally, the veins transect and are confined to highly altered rock, but on the other hand many highly altered zones intersected in diamond drill-core are barren of mineralized veins."

Jan 1, 1953

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By W. B. Boggs

A paper describing the Noranda smelter was presented at the 1930 annual meeting of the Institute (1). A lacer article appeared in the Trans-actions of the A.I.M.&M.E. in 1933. Since that time there have been many changes and improvements in plant operation and it is the abject of this paper to give an account of developments up to the beginning of 1939. The Noranda smelter was built originally for a capacity of 30,000 tons a month. At present, the average tonnage being treated is 110,000 tons a month, the tonnage of custom ores alone amounting to almost the total rated capacity of the original plant. This increase has been accomplished by increasing the capacity of the reverberatory furnaces from 700 tons of solid charge per furnace day in 1928 to 1,500 tons per day at the present time. In 1935, it appeared chat the limit of furnace capacity had been reached at about 1,300 tons of charge per day because of the short life of the sprung silica arches. However, the adoption of the suspended magnesite roof, which had been developed at the Flin Flou smelter of the Hudson Bay Mining and Smelting Company, overcame this difficulty and it is believed that the limit of the capacity of the present reverberarory furnaces has not been reached. A brief account of the changes to equipment in the various departments will be given, followed by a description of the more important features of present smelter practice.

Jan 1, 1939

By S. Setayeshgar

The identification of potential accidents on construction sites has been a major concern in the construction industry and it needs a proactive safety plan to reduce the risk of accidents. There are no efficient methods for checking if safety measures are taken properly on construction sites. Consequently, workers on site are not given enough awareness about dangerous areas. In addition, construction sites are dynamic and on-site situations are changing in terms of permanent and temporary structures and facilities. This information can be represented using Building Information Modeling (BIM). This paper proposes the integration of BIM and safety risk analysis by considering the risk levels associated with the work spaces of different construction tasks. Work spaces are generated in a BIM model according to the Work Breakdown Structure (WBS) of the project, reference objects in the BIM, and the schedule and resources of the task. Each work space is assigned to one or more tasks or functions, e.g., work spaces for specific tasks, shared spaces (paths), storage spaces, or spaces prohibited to workers. The assignment of work spaces is based on the workers, equipment and materials involved in the task. All the work spaces are associated with a specific duration according to the schedule of the project. Then risk evaluation of the construction site is applied in order to evaluate safety risks based on their severity and the degree of exposure of workers. For example, work spaces for storing hazard materials and for heavy construction equipment have higher risks than other work spaces. The results of the risk evaluation can be visualized in a 4D BIM model.

Aug 1, 2013

This paper focuses on the dissolution of various Manganese based compact additions into liquid Magnesium. The experimental procedure employed cylindrical compacts with various Manganese compositions. The various temperatures of the additions and the Magnesium bath were measured simultaneously during the immersion of the additions into Magnesium bath. The exothermicity level of these additions during their dissolution into liquid Magnesium was determined. The relation of the exothermicity level with the dissolution kinetics was also examined. In addition, SEM and EDX work was conducted for additions, which were withdrawn from the Magnesium bath. Finally, the recovery of these additions was estimated by taking samples from the Magnesium bath and conducting ICP analyses.

Jan 1, 2006

By William M. (Bill) Shaver

"The author will review the early history of shaft sinking as well as focus on the improvements made in shaft design and construction over the last fifty years (1970 to 2019) to predict how shaft sinking will change over the next fifty years and describe what the shaft sinking world might look like in 2070. INTRODUCTION It is a great honour to be one of your keynote speakers for the Fourth International Conference on Shaft Design and Construction being held in Toronto in November 2019. This is one of the opportunities we have to thank the Mining Companies of the world as well as the industries and companies we serve for their support of the mining contracting and shaft sinking business of Canada and the world at large. Many of these companies are represented here today. Without your support many of the innovations we will talk about today would not be possible. We would also like to thank all the companies that work with us in our business including all the contractors and suppliers who provide the various services we require. These include equipment manufacturers, engineering companies, project management companies and suppliers large and small who cater to our every need as quickly as possible. Without all these partners we would not be as good as we are. Many of these companies are our sponsors this week. Thank you from all of us! This is also an appropriate time to pause and think about those Shaft Sinkers we have lost and those who have been injured on our projects around the world. Please bow your head and remember the Shaft Sinkers you have worked with, who did not return home or those who returned home injured. Think about how we can continue the work of making shafts safer every day as we go forward with our projects so everyone goes home to their families safe and sound. Pause for a minute and thank you. The subject matter we have chosen to discuss today is “Shaft Sinking in the Next Five Decades”. How will the work be done, how fast will it be done, what will it cost, and why we think this may occur? It is appropriate to consider this over the next few days with this auspicious group we have assembled. Today, we will look back at all the advances that have been made over the last many years and look ahead to the future to attempt to predict what shaft sinking will look like in 2070. When I look around the room I recognize that many of us will not be around then so we need not worry about being wrong. Suffice it to say that the next 50 years will be very interesting and exciting for the shaft sinking business."

Jan 1, 2019

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By W. G. Stevenson

With the author's background of extensive experience, this paper delineates the role of the prospector in modern-day exploration programs. The stages in the development of a prospect to a producing mineral district are outlined, and examples are given from the Ross River area of the Yukon Territory and the Peachland and Highland Valley areas of British Columbia.

Jan 1, 1970

By P. M. Dranchuk

"""PLANET EARTH seen from space appears as a fragile and limited life-supporting system in a vast emptiness. That such a view is, in fact, an accurate one is now more widely accepted than it was not long ago, before Earth's problems of over-population, overconsumption, limited resources and environmental degradation attained the limelight. The danger is that a government and public now deluged by doomsday prophecies and bemused by equally confident reiterations that technology will cure all may hesitate in coming to grips with the problem, in the hope that, given time, it will go away."" With these words, Preston Cloud begins a recent editorial, in Science(l), in which he presents a brief resume of some of the findings of the Committee on Resources and Man of the National Academy of Science-National Research Council(20.Their report, which is based on a two-year study by an extremely competent group and consists of some 250 pages of text, is even more far-reaching and sobering than the report on Energy Resources(3). It begins by quoting Sir Macfarlane Burnet as follows:""There are three imperatives: to reduce war to a minimum; to stabilize human population, and to pre-vent the progressive destruction of the earth's irreplaceable resources.(4)"

Jan 1, 1971