Search Documents

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By Bruno Lemelin

Falconbridge Ltd Raglan Mine has been in production since 1998 and has produced annually some 900 000T of ore grading 3.1% nickel, 0.9% copper and 0.06% cobalt. The mine is located in Nunavik, Northern Quebec. The current mine life is estimated at approximately 20 years. Reserves are composed of numerous small ore bodies situated across a 65 km strike length. Planning the extraction of the ten small mineralized zones represents a great challenge to optimize. The overall objective is to maximize the company?s return on net assets. Actual planning uses computerized technology tools like Automod and Mine2-4D, and a conventional discounted cash flow method (DCF) of calculating net present value (NPV). The complex setting of Raglan could benefit from advance valuation techniques such as the real options method (RO). This paper will present the characteristics if the mines that make it a good candidate to use RO to gain further insight.

May 1, 2004

By K. Parameswaran, A. Veek, A. Fernandez, P. Safe

ASARCO LLC (Asarco) Hayden Copper smelter, in Hayden, Arizona, has operated continuously (except for minor labor and economic curtailments) since 1912. The current plant configuration comprises INCO flash smelting, Peirce Smith (P-S) converting and fire refining/anode casting. In order to comply with the U.S. Environmental Protection Agency (EPA) 1-hour National Ambient Air Quality Standards (NAAQS) for sulfur dioxide promulgated in June 2010, the Hayden smelter had to increase overall sulfur fixation from approximately 95 % to 99+ %, requiring a retrofit of the existing converter department and upgrade of associated emissions controls systems. The Converter Retrofit Project (CRP) involved replacing the five existing 13’ diameter Peirce-Smith converters (2 blowing, 2 hot standby) with three new 15’ diameter Peirce- Smith converters (1 blowing, 1 hot standby) to allow for more effective process gas capture using the existing acid plant contact section. Significant upgrades were made to the acid plant wet gas cleaning section and converter primary gas handling system to improve capture performance, reliability, and sludge handling. In addition, a new tertiary gas capture system was installed to further minimize fugitive emissions from the converter aisle. The existing furnace tapping ventilation ESP was replaced with a new baghouse to enable at least 50% SO2 removal using high-surface-area dry lime injection, which was also implemented on the existing converter secondary gas baghouse system. The first two converters and all gas handling system improvements were started up in April 2018, and the third converter was brought online in November 2018. This paper presents the regulatory context; genesis and rationale for CRP; detailed description of the project; challenges during commissioning; system improvements implemented, and design considerations made, and systems performance and process optimization achieved since startup.

Jan 1, 2019

By Susumu Tsubota

Three types of reference gold catalysts, i.e., 3wt%Au/TiO2 (Au-Ti: Type A), and 0.3wt%Au/Fe2O3 on alumina beads (AUS: Type B), and 5wt%Au/Fe2O3 (Au-Fe: Type C), were produced in a test plant scale by Sud-Chemie Catalysts Japan, INC. under the licensing of AIST. To evaluate the validity of the preparation methods and conditions used for the reference samples, elemental analyses by ICP, particle size measurements by TEM, and catalytic activity measurements for the oxidation of CO and H2 over these catalysts were made. Gold catalysts can be prepared in a large scale of ca 400g for the Au-Ti and Au-Fe catalysts, 5 kg for the AUS catalyst with good reproducibility. It was confirmed that they were available for useful as the reference gold catalysts of World Gold Council.

Oct 1, 2003

?General Facts:Barrick?sFirst Mine in Peru Production started in November 1998 ?The Facilities:Open Pit, Primary and Secondary Crusher Valley Fill Heap Leach PadMerrill Crowe PlantRefinery Environmental Facts: High Rainfall - Average Annual Precipitation of 1,200 mm (47 inches) Rainfall Events: Common 20mm daily events High Altitude Site - Elevations range from 3900 to 4250m. Steep topography - Terrain ranges from 3:1 slopes up to cliffs. Water Issues: Sediment Control - Open Pit PAG Encapsulation - Waste Dump Stormwater control - Leach Pad Erosion Control Techniques ? Offsite impacts mitigation Social Issues: 11 communities surrounding the property Town of Huaraz

May 1, 2003

By C. Veloo

"Westmin Resources operates a mine/mill complex at Myra Falls and produces copper and zinc concentrates with minor associations of gold, silver, and lead from a polymetallic, massive sulphide orebody. Mill flotation performance has historically been plagued by periods of uncontrollably high circulating loads leading to low concentrate grades and below optimal tails. This led to a detailed examination of the flotation process. Locked cycle, and pilot plant data are presented. In addition, plant design and commissioning as well as column cell details are discussed. A comparison between actual and predicted performance is also presented. Benefits realized are higher copper and zinc concentrate grades and improved zinc recovery.PrologueMyra Falls Operations is located at the south end of Suttle Lake in Strathcona Provincial Park. Access to the mine site is provided by a 90km paved highway from Campbell River, British Columbia.The mine and facilities are nestled in the narrow Myra Valley between Mount Phillips and Mount Myra. These steep, rugged mountains rise from the valley floor at an elevation of 900 feet to summits of almost 6000 feet. The steep slopes are heavily wooded with fir, hemlock, and cedar up to an elevation of 4000 feet where a transition to alpine meadows occurs. The summits are craggy rock faces, some capped with glacial ice. Myra Creek winds its way through the valley dropping several hundred feet into Suttle Lake. Precipitation is high at over 100 inches per year, which may include up to 10 feet of snow in winter. The temperature may range from 32° C in summer to -18° C in winter.Myra Falls began production in 1965 with the Lynx Mine, supplemented by the Myra and Price Mines in subsequent years, feeding a 950 stpd mill up until the middle of 1985 when the H-W mine was brought into production. The original mill was replaced with a modern 2700 mtpd facility and in 1988 production was increased to 4000 mtpd.Both Lynx and H-W mines are currently in production producing an average of 3650 mtpd. The ore minerals are primarily sphalerite and chalcopyrite, with subordinate galena, bornite, tetrahedrite, and electrum."

Jan 1, 1992

By Michel Aubertin

Les haldes à stériles contenant des minéraux sulfureux réactifs constituent un milieu favorable à la production du drainage minier acide (DMA). Au sein de ces haldes, les processus physiques, géochimiques et biologiques qui mènent à la production du DMA sont nombreux et complexes. Un des aspects critiques qui affecte la génération de DMA est la distribution et le mouvement de l?eau dans les roches stériles. La modélisation numérique est un outil qui permet de comprendre, pour éventuellement contrôler, les mouvements de l?eau (et donc réduire la production du DMA) dans les haldes pendant la période d?exploitation de la mine et à sa fermeture. Plusieurs simulations numériques des écoulements non saturés dans des haldes ont été effectuées. Pour ces simulations, on a considéré divers types de matériaux, diverses conditions atmosphériques et diverses configurations géométriques. Les simulations réalisées montrent que l?on peut contrôler les mouvements de l?eau en introduisant des couches de matériaux fins intercalées dans les haldes formées de matériaux grossiers. Des couches horizontales ne sont cependant pas appropriées puisqu?elles peuvent, dans certains cas, favoriser la création de zones humides susceptibles d?amplifier les effets du DMA. Une faible inclinaison des couches de matériaux fins vers l?extérieur permet de palier à ce problème. Les couches inclinées favorisent un drainage des haldes vers la périphérie. Ceci a pour effet de garder sèche une grande partie des stériles et de réduire, par le fait même, la production du DMA.

Nov 1, 2002

By A. F. Banks

"Potash processing in Canada commenced on a commercial scale in 1962. Over the last 25 years it has grown into a world-class industry with many advances in processing technology. As it is a relatively young industry, many more advances can be expected. Unlike much of the mineral production in Canada, potash is sold as a range of finished products. The processing involves potash recovery and finishing in about equal amounts in terms of the effort of processing. Environmental concerns are not insignificant and are being treated uniquely in some areas. Research and development efforts, while not carried out on a large scale, are attacking industry problems on a wide front.THE INDUSTRYThe Canadian potash industry has 12 producing mines, 10 in Saskatchewan and 2 in New Brunswick. The total productive capacity of the industry is 18,300,000 tonnes of products per year. At capacity, the industry 1•ill process the equivalent of about 53,000,000 tonnes of ore per year. Plants range in size from 8,000 tonnes to 24,000 tonnes of feed per operating day. In product terms this is from 2,500 to 3,500 tonnes of products per day.Of the 12 mines, 11 are conventional underground mining operations with potash recovery principally by flotation supplemented by crystallization and one is a solution mine where mining is achieved by dissolving the potash and salt in underground caverns and then treating the solution in an evaporator/ crystallizer circuit. In all plants there is commonality of unit operation in the product screening and compaction sections. There are three principal ores being treated in the conventional plants. These may be characterized in general terms as follows:"

Jan 1, 1987

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By Carlos F. Perucca, Maria Virginia Ramírez A.

"Chile based SQM S.A., exploits potassium chloride rich salts at the Salar de Atacama, in northern Chile. The process includes the solar evaporation of natural brines existing in the Salar salt bed, followed by conventional flotation to recover Muriate of Potash (MOP) for fertilizer use.This paper describes a structured method developed to aid in understanding the metallurgical response of the solar evaporated salts to conventional flotation. The method uses classical metallurgical data analysis combined with laboratory and plant-scale testing, and rudimentary mineralogical studies.As a result of the study, several changes were made to the flotation circuit which produced an operation that is much more consistent and easier to control, and has an increased recovery. An optimized circuit, currently being financially evaluated, has also been conceptually designed based on the findings of this work.INTRODUCTIONSQM S.A. is the world’s largest producer and distributor of specialty fertilizers, iodine, lithium, as well as a wide array of industrial and specialty chemicals. SQM is a public corporation whose shares are traded in the Santiago and the New York Stock Exchanges.SQM S.A. exploits the mineral rights at the Salar de Atacama in northern Chile. Its production processes involve the solar evaporation of natural brines existing in the Salar salt bed, aimed at the recovery of Potassium, Lithium and Boron compounds."

Jan 1, 2004

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By Hamid Mahmoudabadi

In the present paper, the performance of four approaches based on neural networks and geostatistical method for grade estimation are compared and analyzed their performance to find a proper method. Four methods, Multi Layer Perceptron neural network (MLP), Radial Basis Function (RBF), General Regression Neural Network (GRNN) and Ordinary Kriging (OK) are selected for ore grade estimation of variable Fe in an iron deposit located in Iran. For each method, two diagnostic statistics are calculated: Mean square error (MSE) and correlation coefficient. The results show the superiority of the General Regression Neural Network.

Oct 1, 2009

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

By Paul W. Shelley, Daniel J. Hodges

The mining industry is undergoing a period of rapid transformative change.&nbsp; This is the result of the social and financial accountabilities that the industry is faced with because of the world&rsquo;s desire to cap average temperature increase to 1.50C above pre-industrial levels (UNFCC, 2016).&nbsp; To limit global warming to 1.50C, greenhouse gas emissions must peak before 2025 at the latest and decline 43% by 2030.&nbsp; In hard rock mining, comminution is identified as the major energy consumer, being responsible for 40-60% of the electricity use.&nbsp; It follows that comminution is the major greenhouse gas emission process of the mine.&nbsp; All effort is being made to radically reduce the carbon emissions of comminution. Grinding media plays a large role in the energy consumption and carbon emission story.&nbsp; In recent years industry practitioners have attempted to quantify the grinding media carbon footprint.&nbsp; This paper makes a definitive contribution to that discussion.&nbsp; The grinding media carbon footprint is quantified in Scope 1, 2 and 3 emission terms in the context of a grinding media supplier.&nbsp; Major emission contributors, steel, natural gas and electricity are discussed in detail.&nbsp; The steel industry transition is a key factor. The paper will explore the steel industry transition and its effect on grinding media manufacturing.&nbsp; The carbon footprint of heritage steel process routes are analysed and compared with the process routes of the future.&nbsp; Emerging steel making technologies are presented and discussed.&nbsp; The future of the steel manufacturing and procurement route for grinding media is proposed. This narrative allows for a comparison between the heritage carbon footprint and the future carbon footprint of manufactured grinding media.&nbsp; Of equal importance is the opportunity of reducing the grinding media carbon footprint in the field.&nbsp; The paper explores possibilities of reducing the grinding media carbon footprint at the customer site.&nbsp; Media in use options are presented that take account of the mineral characteristics, the mill dynamics, and the product metallurgy to optimise both carbon footprint and media performance. It is intended that this is a landmark paper in the discussion of the carbon footprint of grinding media.

May 4, 2025

By P. G. Lazenby

This paper describes the latest instrumentation improvements in the INPUT Airborne E.M. System, particularly the new electronic signal-processing techniques. Several anomaly examples illustrating these techniques are shown.

Jan 1, 1973

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By R. Cammack

"A fundamental component of the Hoek–Brown empirical rock failure criterion is assessing an appropriate mi constant. In developing their empirical criterion Hoek and Brown normalised triaxial test results by dividing the principal stresses at failure by the uniaxial compressive strength to provide mi values for typical rock types. Experience shows that Hoek triaxial tests for individual lithology types commonly have a large inherent scatter. In addition, tests are often conducted on core from random locations, which although being of one parent rock type, display variations in density as well as minor variations in grain size and alteration.This paper presents experience from projects the authors have been involved in which large sample populations of triaxial and UCS tests on similar rock types were available. Geophysical logging data was also available for some projects. The methods used to estimate the compressive strength for each sample and the effects on normalising the data sets are described. The variability of the data and uncertainties and assumptions involved in the process of assigning a mi value from the normalised data are also discussed."

Jan 1, 2015