Search Documents

The implementation of robust, reliable and accurate sampling systems is the key to the successful management of any mineral processing plant. The representative sampling of a mineral processing plant is the only way to determine what is coming into the plant, what is going out as fi nal product and what is going to tails. In plants with high gravity gold components, where high recovery effort gravity circuits are installed, the use of a gravity recoverable gold (GRG) sampling system can assist in the online monitoring of the performance of the circuit. The typical installation location would be in CIP or fl otation feed (ie cyclone overfl ow), downstream of the gravity circuit. A GRG sampling system generally consists of the following equipment: true proportional, continuous drive, linear cross cut sampler, secondary vezin sampler operated on a timer, a batch centrifugal concentrator, and sample dewatering module. The operating philosophy of the GRG sampling system is that the primary sampler operates on a continuous basis, generating a constant stream of truly representative sample. Consep's H&S drive system is unique in its ability to be able to operate in a continuous mode, therefore enabling a continuous stream of representative sample to be generated. The primary sample stream reports to the secondary sampler. The secondary sampler operates on an intermittent basis (nominally ten minute interval), resulting in a relatively small sample volume per shift. Normally the sample volume would be ten to 15 L per shift. The secondary sample rejects stream reports back to the batch centrifugal concentrator. The sample generated from the secondary sampler can be dewatered using a Consep H&S dewatering module. This device produces a final sample that consists of separate filter cake and filtrate. These are suitable for taking directly to the laboratory. The continuous stream of truly representative secondary sampler rejects is passed through an appropriately sized Knelson Concentrator, typically a KCMD7, KCCD10 or KCCD12 sized unit. This unit recovers any available GRG from the stream. The Knelson Concentrator is also purged of its gravity concentrate at the end of the shift. This sample, which is nominally around 1 - 2.5 kg of concentrate, is also taken to the laboratory. At the end of the shift the client will have a measure of the gravity recoverable gold content of the target slurry stream, as well as a true representative sample of the complete stream. Through the addition of a Knelson Concentrator to an otherwise typical sample station, it is possible to generate a true measure of the performance of your gravity circuit. This will take the guess work out of the daily variation in gravity circuit gold recovery, as the site knows whether the changes are due to gravity circuit equipment performance, or due to the natural variation of ore GRG contents. Maintenance planning can also be designed around the system, as the site will have a composite sample to measure the performance of the circuit, therefore indicating where performance has dropped and maintenance is needed. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By A Harburg, A Dendys, G Green

Dugald River Mine (DRM) is located approximately 85 km north-east of Mount Isa, and 65 km northwest of Cloncurry, in the north-west Queensland Minerals Province of Australia. DRM is an underground operation and includes an above ground processing area, a 200 ha tailings facility, two waste rock dumps and associated infrastructure. The mining method is conventional underground longhole open stoping and downhole benching of a lead/zinc deposit within a black slate environment. The deposit is estimated to contain ~53 Mt of zinc and lead, which will be mined over a 30-year period. During operations, waste rock is segregated into either Potentially Acid Forming (PAF) or Non-Acid Forming (NAF) based primarily on the sulfide concentration of the rock. In particular, the NAF waste rock is an asset and is used for various small construction projects during operation; however, its primary use is for rehabilitation work at closure. Since beginning operations in 2017, DRM has generated more NAF than was originally anticipated. Whilst this is an excellent asset to DRM, it did pose a logistical problem of where to store the additional NAF for the life-of-mine and how to manage the run-off. DRM experiences distinct wet and dry seasons with hot conditions and periods of rainfall between November to April, and relatively dry and mild conditions between May to October. Majority of rainfall is received between January and February with an annual average rainfall of 501.1 mm. Short and intense rainfall events are common. DRM’s above ground infrastructure is land-locked between two large ephemeral watercourses, making the significant expansion of any assets challenging from a permitting/regulation and cost perspective. MMG is also a member of the International Council on Mining and Metals (ICMM) and is committed to adapting to a changing climate through operations and closure. Following extensive studies DRM opted to store the additional NAF material into the adjoining NAF Dam and concurrently upgrade a previously minor sediment basin into a highly engineered sediment basin which relies on automatic flocculant dosing to meet the required discharge quality limits. This basin is climate-resilient in that the dosing system can be adjusted to counter high intensity extended rainfall events which produce highly variable inflow water quality. This abstract broadly describes how DRM designed and implemented an engineering innovation to enable the site to meet the changing climatic challenges. The abstract then describes the process to design the sediment basin and how the dosing rate was established and validated. Finally, the abstract comments on the effectiveness of the sediment basin and how it has revolutionised DRM’s approach to water treatment and management; all whilst minimising the disturbance footprint of the operation

Aug 2, 2023

By K Li, C Zhang, i, J Oh, S Saydam, H L. Ram

Rock surface roughness plays an important role in excavation engineering projects and applications related to surface support structures, such as shotcrete and thin-sprayed liner (TSL). The morphology of the substrate affects the mechanical behaviour at the interface significantly. Therefore, it is necessary to quantify the roughness to investigate the relationship between roughness and mechanical properties. The joint roughness coefficient (JRC) proposed by Barton and Choubey (1977) is widely used in practice. It initially estimated the roughness by comparing it to 10 standard profiles visually. However, this method has lots of limitations, it is not only subjective but also a two-dimensional parameter with a small lab scale (Beer, 2002). The subsequent research on JRC, from visual comparison with Barton’s standard profiles to measuring the roughness with a profilometer (Weissbach, 1978; Alameda-Hernández et al, 2014). Then, 2D profiles or 3D surfaces by different technologies with higher resolution and accuracy, such as 3D laser or optical scanners (Fardin, 2004; Jiang, 2020, 2021). These 3D scanners are expensive and only suitable for laboratory scales. LiDAR scanners (Lato, 2009; Aubertin, 2022) have been applied in industrial size, but it is difficult to achieve a millimetre-level accuracy, which is mostly used to detect the thickness of shotcrete in practice. Thus, finding a cost-effective surface roughness measurement method with high accuracy is necessary. Photogrammetry is another method to digitalise the roughness of the surface. Similar to 3D scanners, photogrammetry also generates the point cloud of the objective surface and then reconstructs the 3D model of the objects. 3D reconstruction technology is a trendy technology in recent years. The structure from motion (SfM) algorithm (Westoby, 2012) to rebuild the 3D model with a flexible workflow, aligning photos, building dense point cloud, mesh and texture, which has been proved that can rebuild an accurate model in variable fields.

Nov 29, 2022

By J Wood

Steady depletion of the world’s primary copper reserves coupled with a meteoric rise in electronic waste (e-waste) generation has led to secondary copper processing assuming an ever-increasing importance within the global copper industry. Treatment of secondary copper feeds at existing smelting operations has traditionally been performed in the Blast furnace, Peirce-Smith converter and/or anode furnace. In the past decade or more, bath smelting technologies have been preferred for the processing of these materials due to their superior environmental performance and flexibility to operate under a wide range of conditions. This paper focuses on the pyrometallurgical processing of copper secondaries in the Outotec Ausmelt TSL Furnace and some of the unique issues facing secondary copper smelters and downstream gas handling/cleaning equipment.

Aug 8, 2011

Australia is a significant exporter of uranium for use as fuel in nuclear generating plants around the world. Although Australia does not have any nuclear power plants the Australian Atomic Energy Commission has a research program on methods for the safe disposal of wastes produced by such plants.

Jan 1, 1986

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

The JORC Code, which has been in existence as a Code incorporated in the listing rules of the Australian Stock Exchange and New Zealand Stock Exchange since 1989 and 1992 respectively, has been revised and will be re-released in 2003. This revision followed a call for submissions in December 2001, the publication of an exposure draft in late-2002 and an exposure period during which a large number of constructive comments were received. These comments were reviewed and a further exposure draft released as part of the current exposure draft of the ASX listing rules. It is anticipated that the final Code will be incorporated into the stock exchanges listing rules in late-2003. The 1999 JORC Code has been the standard on which other reporting Codes have been based, each of which has contained refinements. Three in particular, the Reporting Code from the United Kingdom/Ireland/Western Europe, the new Canadian Reporting standards and the SAMREC Code from South Africa, influenced JORC in the preparation of the 2003 JORC Code. Whilst there are differences between the 1999 Code and the 2003 Code, these changes are mainly in the guidelines. The Code definitions, which are largely in accord with agreed international definitions, remain substantially unchanged. The two main changes in the 2003 Code are the requirement for a Competent Person to be responsible for the documentation relating to the reporting of Exploration Results, and the introduction of æRecognised Overseas Professional OrganisationsÆ as overseas organisations to which Competent Persons may belong. Other changes include: clarification of the reporting of exploration targets or potential; the rearrangement of the diamond reporting clauses; the introduction of guidelines for the reporting of Industrial Minerals; modification of the coal clauses and recognition of the new Coal Guidelines; and the introduction of a guideline encouraging the discussion of relative accuracy and confidence in resource/reserve estimates. Other lesser changes to the Code are listed and discussed briefly. The release of the 2003 JORC Code maintains the standard set by JORC as a world leader in the development of mineral reporting Codes and their adoption by industry.

Jan 1, 2003

By C OÆKeefe, A Thomas

Boom time in the mining industry has presented mill operators with several unique challenges including the need for increased throughput while being constrained by a shortage of skilled labour and aging capital equipment. New instrumentation technology that provides reduced installation costs; no process down time for installation; and reduced maintenance costs and labour requirements; has been introduced to address the labour situation while maintaining production. This new tech- nology also enabled more accurate and reliable process measurements thus providing the capability for operators to maximise throughput with their existing capital equipment. This passive SONAR based technology can accurately measure the volumetric flow rate of single phase and multiphase fluids as well as the amount of air entrained within slurries. This is accomplished in a non-invasive manner. This paper will describe the principle of operation as well as the application of the technology to critical minerals processing applications. Included will be operational examples comparing the SONAR measurement performance to traditional measurement techniques. These examples will include hydrocylone feed flow, flotation concentrate flow, and slurry streams containing magnetic ores. Actual plant data will be presented as well as a discussion on the operational advantages such a measurement capability.Also described will be the power of the technology platform to provide novel process monitoring and control capabilities such as pipeline sand-out prevention and pipeline acoustic monitoring.

Jan 1, 2009

Although a formal EES was not prepared for the WIM project due it winding down, CRA Ltd has been through the EES and planning scheme amendment process for its demonstration plant. Community consultation was involved with all aspects of this process. The paper outlines the WIM EES consultation program and provides lessons for future community consultation for major projects in regional locations with significant potential to alter the environment.

Jan 1, 1992

By P J. Ellen

The selection of the ore haulage system is a key decision made in the development of an underground mine. The haulage system is one of the components that define a mineÆs ability to respond to changes in mining inventory and market conditions. The complexity of this decision for Telfer Deeps was affected by the realisation during the feasibility process that the true scale of the potential underground mineralisation at Telfer was still to be quantified. This paper provides an overview of the process used in the Telfer Project Feasibility Study to select an ore haulage system for Telfer Deeps. The purpose is to highlight the value of impartially approaching tasks of this type with a robust process. The process should be able to respond to issues identified as the task progresses towards the objective of finding the best solution for an ore haulage system for the mine. For Telfer Deeps, this process resulted in the selection of a haulage system built around a shaft. The systems considered during the feasibility are discussed and the components of the haulage system constructed for Telfer Deeps are described.

Jan 1, 2005

By G Wood, B Lumsden

A statistical ærandomised block designÆ full plant trial of magnetic conditioning of flotation feed was undertaken at Rio TintoÆs Northparkes Mine in New South Wales. Magnetic conditioning of flotation feed has been shown to improve the flotation of 20 38 ¦m fraction for either metal. Approximately half the copper and gold losses at Northparkes are in the

Jan 1, 2007

The paper reviews some characteristic features of feasibility studies and discusses the need for a wide scope at the pre-feasibility stage. The performance of recent Australian gold mines against the predictions contained in their respective feasibility studies is examined, resulting in a recommendation that feasibility studies need to be improved The advantages to be gained from having a feasibility study reviewed by an independent authority are discussed, and some of the reasons for using consultants are listed. Two examples of successful optimisations in the early stages of pre-development studies are described briefly and the benefits achieved are presented. The paper concludes that feasibility studies need improvement to enhance the confidence of investors in the mining industry.

Jan 1, 1991

Anglo Platinum recognised with its expanded operations the need to change its evaluation strategy due to increased sample volumes and the pressure it created at laboratories. The sender/receiver analytical scenarios had to change in order to curb costs and to prevent substantial investments in new sampling and analytical facilities. Given the high cost associated with correct sampling systems and sampling protocols and the shortage of technical resources a strategy of single point sampling and analysis was introduced. The analysis was then done at an ISO17025 accredited laboratory with ten per cent checks, subjected to careful statistical scrutiny. Logistical problems increased with respect to weighbridge congestion, maintaining sampling quality, throughput of samples in the sample preparation areas, manual quality control systems in place, audit trails and analytical capacity throughout all operations. This required the expedited improvement of existing sampling practices and the development of new sampling methods and equipment. Anglo Platinum is classifying and standardising sampling equipment, sample preparation and analytical procedures for all process streams with the view to minimise overall uncertainties. Major investments were made into a customised LIMS and automated equipment for data management, reduction of manual transcription errors and streamlining of sample processing. Anglo Platinum is committed in rolling out the enhancements to all sites as priority dictates.

Jan 1, 2008

By J L. Edwards

High resolution, acoustic scanning technology has emerged in recent years as a powerful wireline tool for identifying the occurrence and orientation of structures and borehole breakout û the latter being a strong indicator of horizontal stress directions. While other wireline techniques such as dip metre and calliper logging can provide some of these data in a fairly rudimentary way, the quality and ease of interpretation of acoustic scanner logs provides a level of detail that significantly enhances the risk profile of the analysis which more than compensates for their additional upfront cost (MacGregor, 2002). As is often the case with such technology it is one thing to generate a data set that describes the attributes of the various features apparent in a log, and another to be able to analyse those data in such a way that their individual and collective impact on mine planning issues can be readily assessed (MacGregor, 2003). This paper describes a process for the interactive manipulation and visualisation of joint and breakout data to enable them to be effectively included in the mine design process.

Jan 1, 2009

The ownership, policies, organisation, structure, market, financial considerations and communications of a large resource project vary significantly through its discovery, feasibility, development and production phases. The extent of these changes, from discovery in 1957 through to 1979, is examined for the Mt. Newman iron ore project in the Pilbara region of Western Australia and some of the factors that influenced it are detailed. This shows that only some of the influences are under the control of the mine owner/operator, despite their significant impact on the returns for the massive capital invested. The effect of the general business climate on the various phases is also examined.

Jan 1, 1980

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

This paper discusses how the i-kon TM Digital Energy Control System may be deployed by miners of massive underground orebodies to deliver significant advantage in terms of safety, cost and environmental compliance. Digital Energy Control offers an exciting opportunity for mine operators to review their blasting and mining practice to gain the most advantage from this new technology.

Jan 1, 2000

By B McIntosh

Sustainability in its simplest assessment has been defined as æmeeting the needs of the present without jeopardising the needs of future generationsÆ. For the mining industry alone, this statement could indeed be interpreted by the many cynics in our community as an oxymoron; as miningÆs very existence requires the extraction and consumption of finite resources. However for the future of industry as a whole, the integration of mining, minerals processing and manufacturing presents us with a unique opportunity to achieve sustainability through the continued supply of metals and materials for society, in a manner which can achieve positive social outcomes through a triple bottom line approach.The Kwinana Industrial Area has been Western AustraliaÆs premier heavy industrial precinct for more than 40 years and its prevailing level of prosperity will ensure it remains a significant contributor to the State economy through the 21st century.The Kwinana industries depend on each other for the production of essential raw materials vital to their manufacturing and refining process, an innovation that also has significant environmental benefits.Formed in 1991, the Kwinana Industries Council strives to foster positive interaction between member companies and with the local community.The aims are:to co-ordinate the activities of Kwinana industries on a range of common issues; provide effective liaison with the local community; promote a positive image of Kwinana industries; highlight contributions to the community by Kwinana industries; and work towards the long-term viability of the Kwinana Industrial Area. The Kwinana Industries Council facilities these aims by focusing on developing and employing leading edge technology, giving workplace health, safety and environment top priority, and taking a committed, responsible and pro-active approach to environmental protection, whilst forging a two-way partnership with the local community.The sustainability of industry is the key objective for the Kwinana Industries Council and through the involvement of the 13 member companies industry strives to:achieve efficient processing of resources to provide a range of goods and services needed by the community; achieve acceptable and decreasing level of environmental impact; provide jobs and income for our community; and engage co-operative projects that benefit the local communities, the State and Australia.

Jan 1, 2004

A thousand writers have harped upon the wondrous nature of the inventive faculty. They realise that man is a creator, and that capital and labour alike are, and will always be impotent without machinery and processes that is invention. What Bacon has said is echoed by them all, "the introduction of new inventions seemeth to be the very chiefest of human actions. The benefit of new inventions may extend to all mankind-they make all men happy without injury to 'any' they are new creations and imitations of God's own works." My remarks will occupy another field I will refer to some of those features of the Patent Laws of different countries, which prevent the use of new inventions, oppress the development or inventive' genius, and diminish human happiness and progress' Wherever Patent Laws are framed and administered upon wrong principles, these results are inevitably found. A concise, complete, common-sense comparison of the chief Patent Laws of the world cannot easily be found but to avoid seeing scrappy, misleading references to Patent Law in the press particularly the English-would be equally difficult. Writers who are considered authorities so frequently make minor issues prominent and so uniformly fail to give weight to fundamental principles that the effect on the public is to mislead.