Search Documents

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

By P Cheluszka, M Jaszczuk, P Sobota

This paper refers to a new idea of stereometry of cutting drums of longwall shearers designed to get medium and hard to mine coals. A new way to place picks on a drum enables to readjust a number of picks being in contact with the body of coal to shearer haulage speed. Owing to this a remarkable increase in depth of a cut within the low range of haulage speed has been obtained. On comparing operating characteristics a considerable reduction in the specific energy consumption has been shown when using the units machined as per the new idea, in comparison with the units produced in series.

Jan 1, 2003

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By A G. L Pratt, G F. Dunstan, A Leonforte

The selection of the material sizing and mine dewatering systems are important elements in the development of a large-scale, high tonnage (greater than 4 Mt/a) underground hard rock mine. The sizing system will influence the size and type of the ore haulage system and therefore how the underground project is developed. With more underground developments considering or implementing caving methods of mining, the selection of the material sizing systems is also influenced by the caving fragmentation. Traditionally, crusher systems are used for material sizing in large hard rock mines, with the crusher installation and its ancillary equipment representing a substantial capital investment. Underground cave mining type operations generally express themselves with large surface subsidence areas, which can lead to large inflows of water from major rain events or purging underground aquifer systems. To minimise disruption to mine production, the dewatering system needs to be sized, with consideration to both storage and pumping capacities. The balance between storage and pumping capacity is assessed to provide the optimal economic solution with the appropriate risk measures. This paper outlines a process for the selection of material sizing and dewatering systems for large-scale caving operations. This process is illustrated with information drawn from NewcrestÆs Ridgeway Deeps Block Cave project. The Ridgeway Deeps Block Cave is located directly beneath the existing Ridgeway Sublevel Cave Mine.

Jan 1, 2008

By Tapp B. A

To date, few studies have been made regarding the energy requirements of the Australian mining and mineral processing industries. This paper indicates that these industries use a substantial proportion of the total Australian energy input (32.7% in 1971-72 and 36.10% in 1974-75). With the growth orientation of these industries, this input is likely to increase. Data shows that mining energy requirementE varied from 4.22% (of total Australian energy requirements) in 1971-72 to 4.16% in 1974-75. Energy requirements for the total mineral processing industries increased from 28.49% to 31.93% for the same period. The total estimated primary energy input varied from 22.56% to 25.2%, whilst indirect energy use, in the form of electricity increased from 10.16% to 10.66%; in the same period. Analysis of primary energy input data within the processing industries (1973/4) showed that the Iron and Steel Industry consumed 15.03% of the Australian total consumption, Non-Ferrous metals, 5.43%, Cement, 1.64%, and Refractories, 1.59%. In toto this represented 24.57% of the total

Jan 1, 1979

By Hellsten K, Eshuys E

The best long-term approach to exploration involves the use of extensive quality data and the integration of many different factors, methods and techniques. The successful exploration manager needs to integrate people, area selection and exploration methods, with the use of descriptive and genetic geological models. Based on a syn-metamorphic genetic model for Archaean gold, successful exploration in Western Australia requires the integration of data on anomalous gold, alteration, lithology and structure. Many other parameters such as geophysics, geochemistry and regolith studies provide additional, indirect information that needs to be integrated into the overall exploration programme. Timely access to research findings and ability to integrate these into immediate exploration has contributed considerably to the success of the gold industry in Western Australia since 1980. Extensive and deeper drilling, and the ability of computers to handle the volume of data generated have enabled effective testing of many more geological targets.

Jan 1, 1996

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

This paper discusses design concepts in planning a large modern bulk terminal. The need is emphasised for a studied master plan, in-built materials handling flexibility and staged development. An integrated approach is advocated, combining functional purpose designed foundations and structures to serve their mechanical, electrical and environmental functions. Dry bulk and slurry handling are also compared in perspective.

Jan 1, 1983

By Hosking IA, Mirkov P

Among the solutions currently being considered for improving traffic flow in Sydney are the construction of major road tunnels, principally the Eastern Distributor Tunnels, leading from the end of the Cahill Expressway to Drivers Triangle and South of Taylor Square and the Sydney Harbour Tunnel, which incorporates sections of driven tunnel at the northern and southern sides of the harbour. The Eastern Distributor Tunnels, known as Stages 2 and 3 of the Eastern Distributor Scheme comprise: Stage 2 - A south bound two lane tunnel from north of William Street to Driver's Triangle. The southern end includes two Y junctions (locally 3 to 4 lane widths) with exits into South Dowling Street, Anzac Parade and Moore Park Road. Stage 3 - A north bound, two lane tunnel from Taylor Square to Palmer Street just north of William Street. Further details of the Eastern Distributor Tunnels are given in the paper by Baxter, Chappel and Fishburn (1986) which is included in this conference.

Jan 1, 1987

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

The investment worth of a mineral deposit can only be realistically evaluated in relation to specific engineering design criteria, which fully details the proposed method of exploitation. These criteria have not in general been taken into serious consideration when leaseholders have reported reserves in the past. In fact, many "reserve" figures quoted are probably more correctly classified as geological resources. The industry now recognises that it is necessary to take into consideration not only grade and mill recovery factors, but also likely mining and processing costs as well as the current market price for the commodity. Once having estimated those costs which are applicable to the resource under study, they can be deducted from the gross inherent worth of the orebody to result in an estimate of the potential net revenue. Through a process of interactive trial mine designs and evaluation, reserves can be quantified to provide an estimate of the available recoverable economic reserves given a set of assumed cost and operational parameters. It follows then, that the available economic reserve recoverable from a given resource will vary from time-to-time as cost and price factors vary in response to changing technology and economic factors. A methodology is described which may be used to derive economic recoverable reserves based on a computerised model of the geological resource data and appropriate economic and operational cost algorithms. Examples are provided from both coal and gold studies to illustrate the impact of economic criteria on the magnitude of the reserve figure reported for each project.

Jan 1, 1987

By Torres F, Cerda I, Gimenez P, Gonzalez G, Castelli L

Slurry density measurement, specially in cyclone feed streams, is fundamental to grinding circuit control. With the purpose of increasing the availability of such a measurement, the design of a soft-sensor in an actual grinding plant is addressed in this paper. The system is designed to substitute the momentary unavailability of the real density sensor, either because it has failed or because it has been removed for any other reason. The ARMAX model structure is determined using the stepwise regression method. Starting with a list of the candidate variables, the method selects, one by one, and in a systematic manner the variables which best model the measurement to be replaced, choosing them from the set of presumably correlated candidate variables. In this paper not only the single measurements are included in the list of candidates, but also combinations of such measurements having physical significance. A phenomenological model has been built with the purpose of determining these combinations. It turned out that in most of the cases the components of combined measurements having physical significance were selected by the stepwise regression method, instead of the single measurements. Actual grinding plant data is used to determine the model structure, to estimate the model parameters and to test the predictive capability of the developed soft-sensors. Good results are shown to be obtained during periods of up to 30 hours of the density soft-sensor operation.

Jan 1, 1995

Some of the major factors affecting ore reserve estimation in gold mines are discussed together with their impact on computational methods.The major priority in ore reserve estimation is to get sampling and geological problems resolved. Poor basic information cannot be remedied by mathematical methods.Generally the more complex a deposit becomes the greater the need for subjective assessment and the less applicable are more complex ore reserve methodologies.

Jan 1, 1984

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

By B Sno, P A. Cockburn, R C. West, C U. Jones

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed), which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons feed system could deliver the following benefits to flash furnace operation: accurate pulseless delivery of feed material to the head of the burner leading to improved combustion performance and process stability; highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; decreased pressure pulsation in the furnace due to improved combustion control and performance; and decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear.

Jan 1, 2005

By Randall C

Energy studies have been undertaken at a number of open coal mines in the Hunter valley. A range of energy efficiency benchmarks and targets have been established, which, when applied across coal mines, will assist in leading to a significant improvement in energy efficiency in the coal mining industry in NSW, thereby leading to an improvement in environmental performance. Typically, energy efficiency improvements of 20 per cent and higher appear possible at many mines leading to a commensurate reduction in this controllable operating cost, ie energy. On the basis that annual energy costs and net profit are similar for many mines, a reduction in energy costs by 20 per cent will lead to increase of 20 per cent in net profit.

Jan 1, 1995

By Van Groenou B

Traditionally mining and conservation have been regarded as opposing and mutually exclusive concepts of land use. Often problems are anticipated which cannot be substantiated by facts. In addition, an ill defined time-scale adds to potentially emotive issues. Examples from Australia and elsewhere are presented which illustrate the dynamic nature of the environment and accentuate sequence patterns in plant community development following natural and man-made disturbances. The mining industry generally appears to be aware of the environmental impact of mining and whilst endeavouring to minimise the disturbance, is still orientated towards maximum production.

Jan 1, 1984

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995

Underground excavations are subjected to complex stress changes caused by nearby mining, but may also be affected by repeated dynamic loading from blasting and seismic events. In some cases, the combined, cumulative effects can lead to unforeseen damage, displacement and instability. Simulating dynamic loading of an underground excavation is a very complex task. The state of rock mass stress, damage and deformation must first be simulated sufficiently requiring small-scale structures to be explicitly modelled. Supporting elements must be represented with high similitude and then the dynamic event must be applied to the system in the case of blasts, or evolve as a consequence of rock mass instability for seismic events. A special case is for the effect of pit blasting on underground excavations - discontinuous rock phenomena at scales from mine, to bench, to pillar, to tunnel need to be captured and this represents one of the most computationally intensive tasks in mine simulation. Recent advances in computer power allow these tasks to be completed at a mine scale, incorporating discontinuities and geological detail matching the best practice for static Finite Element analyses. The results are a worthwhile contribution to mine decision-making, but require careful interpretation and thoughtful inputs - even more so than quasi-static analysis - as the cumulative effects of unfavourable modeling practices are greater. Some learnings from experiences with mine scale, discontinuum dynamic simulation are summarised, including a discussion of considerations of scale and similitude for this type of analysis.

Nov 25, 2010

By M Zoorabadi, Y Zhang, D Bringemeier, S Nicoll, N Kerr

Lihir operations of Newcrest Mining Limited (NML) are on Lihir Island (PNG) which is located approximately 900 km north-north-east of the national capital Port Moresby. The mine is located within the Luise Caldera of the Luise Volcano which is located on the east coast of the island. The caldera is an extinct volcanic crater that is geothermally active. Volcanic activity on Lihir Island is limited to remnant hydrothermal venting in the Luise Caldera in the form of hot springs and fumaroles. Steam and gas (including H2S) naturally discharge within the pit area and along the Kapit beach and near shore region. The hydrothermal reservoir temperatures can reach 100°C at the water table and exceed 200°C at depth. Newcrest maintains a Geo-hazard Management Plan to identify and manage the various geotechnical and geothermal hazards on-site. The major geothermal hazard to mining at Lihir is the occurrence of geothermal outbursts, which have occurred in the past with varying intensities and caused two ‘near misses’, production delays and material losses.

Nov 29, 2022