Search Documents

By R Miller

The enrichment of magnetite to haematite and haematite-goethite leads to a coincident magnetic low and gravity high within the banded iron formation. Palaeochannel deposits of pisolitic limonite can be expected to provide a relative magnetic high and gravity low in a sinuous geometry. Detrital iron deposits of conglomerate, scree or ‘canga’ might have indistinct magnetic response but will usually have a relative gravity high.These signatures provide clear discriminators detectable by a joint gravity and magnetic survey.The combination of airborne gravity gradiometry and magnetometry is particularly powerful in detecting and discriminating targets, as well as mapping lithologies and structure, across a wide variety of iron ore deposit styles. It provides detection capabilities in a platform capable of rapid, complete coverage with minimal access issues. This approach has been used in FALCON™ airborne surveys for iron ore exploration in the Great Lakes, USA; the Middleback Ranges, South Australia; and the Hamersley Basin, Western Australia.The complex magnetic properties of iron formations (particularly remanence, anisotropy and depth of weathering) prevent this approach from being simple. The use of vector residual magnetic intensity (VRMI), calculated from the measured total magnetic intensity (TMI), assists by reducing the complexity due to the different directions of the remanent and induced magnetic fields.Estimations of the density to magnetisation ratio via the pseudo-lithology calculated from the VRMI and gravity gradients provide a useful method of capturing the discriminatory power of joint magnetic and gravity gradient data.

Jul 11, 2011

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.The evaluation of magnetite deposits involves specialised approaches to sample preparation, sample analysis and resource estimation. The sampling protocol for magnetite deposits will typically include the use of Davis Tube analysis. The Davis Tube is a mini-pilot plant that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.During resource modelling, the mass magnetic recoveries and concentrate grades may be estimated directly or assigned to a block model using regressions with other chemical constituents. For estimation, the concentrate grades are weighted to account for the different mass magnetic recoveries of each sample and the impact of these differences on the concentrate estimates.

Sep 5, 2011

By W Mez

The German mining industry uses different residues for backfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes, a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the DMT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer a secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

By C A. Thomas, J C. Eardley, G V. Franks

As valuable minerals are more disseminated, there is a need for low-grade ores to be finely ground to liberate these valuable minerals. However, this has a negative impact on ultrafine mineral recovery as conventional separations processes such as gravity separation are no longer effective. Instead, fine particles can be recovered by froth flotation. Various novel reagents have been introduced along with development in flotation cell designs such as Jameson cell and column cells to improve performance and recovery of ultrafine valuables. This study, on the other hand, aims to recover the fines using a combination of commercially available reagents to selectively flocculate the valuables, so they are large enough to be recovered via conventional froth flotation cells. This technique if successful can be implemented in many existing industries that continue to use mechanical flotation cells that require particle sizes to be 50–150 μm for effective recovery (Ralston, 1992; Batterham and Moodie, 2005). Selective flocculation is not widely implemented in industries mainly due to the inability to float the aggregates ones they are formed and gangue entrapment within the aggregates which consequently affects the grade of concentrate recovered (Forbes, 2011). The major goal is to aggregate the minerals and float the aggregates unlike the more common industrial technique such as reverse flotation of hematite, where the aggregates itself is not recovered via flotation.

Aug 24, 2022

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Dip L. B

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand.The reform of New Zealand's minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Government's intention to review all the major laws governing New Zealand's resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990.

Jan 1, 1990

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By R Grogan

Nautilus Minerals Inc is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.Economies depend upon four key types of capital: built, natural, financial and human. Natural capital consists of the ‘minerals, energy, plants, animals, ecosystems (climatic processes, nutrient cycles and other natural structures and systems) found on Earth that provide a flow of natural goods and services’ (Daly and Farley, 2004). Many ecosystem goods such as fish, fruit and water are already valued and sold in markets; however, some ecosystem services are not amenable to markets and have remained unvalued in traditional accounting methods, even though they provide significant value (such as flood protection, climate stability etc; Batker and Schmidt, 2015).There are now economic methods available to quantify and value natural capital and many non-market ecosystem services. When valued in dollars, these services can be incorporated into a number of economic tools, including benefit-cost analysis, accounting, environmental impact statements, asset management plans and rate of return on investment calculations. Their inclusion ultimately strengthens decision-making. When natural capital assets and ecosystem services are not considered in economic analysis, they are effectively valued at zero. This omission can lead to poor decisions, inefficient capital investments, higher incurred costs and losses due to unexpected events (Batker and Schmidt, 2015).In 2015 Earth Economics was commissioned by Nautilus Minerals Inc to conduct an independent, objective environmental and social benchmarking analysis of the proposed deep seabed Solwara 1 mine with terrestrial copper mines (referred to as ‘the report’). The report represents the first ever natural capital accounting and ecosystem goods and services framework for seabed mining.The report compares the proposed Solwara 1 mine with three terrestrial mines: Bingham Canyon (Utah, USA), Prominent Hill (South Australia, Australia), and Intag (a proposed mine in Intag Province, Ecuador), and provides a natural capital accounting assessment for all four operations.CITATION:Grogan, R, 2016. Natural capital accounting – a sea floor mining application, in Proceedings Life-of-Mine 2016 Conference, pp 2–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By K Biegaj

The paper describes challenges the author has encountered on Australian underground gold and nickel mines over the last eight years, when recovering high-grade gold/nickel bearing mine floor material with a mobile supersucker/giant vacuum cleaner and other equipment. Whilst for a number of years the mine floor vacuuming and other mine floor clean-down technologies have been accepted/adopted and are working well in other parts of the world and on the South Australian opal mines, regrettably, they have not yet gained acceptance of mining executives and mine managers of gold and metal mines in Australia, who still elect to leave the never to be recovered gold/metal behind or to put it plainly - waste it.For reporting purposes during the mining process, the portion of gold/metal included in calculation of ore reserves prior to obtaining capital funds for their development, continues to be camouflaged in various reconciliation and call factors. This approach, ie wasting of capitally developed and already broken ore stocks should be viewed by the shareholders as totally inappropriate to say the least, especially with the current gold and other metals prices.The author attempts to provide answers as to why the technology referred to above has not yet been accepted on Australian gold and metal mines and outlines the way forward.CITATION:Biegaj, K, 2012. Why do shareholders and mining executives allow mine managers to leave behind high-grade broken ore underground?, in Proceedings Narrow Vein Mining 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

By R Witt, M Lowing

Tanking of tunnels is now often specified when inflows exceed as little as 1 L/s/km with a unit distance of 100 m. To demonstrate inflows over a 100 m segment of a tunnel are less than 0.1 L/s with a standard error of 0.01 L/s by timed, gravity filled, volume measurement up and downstream of the segment, the measuring cylinder volume (L) must exceed 10 Q, where Q is the flow in L/s, and the number measurements taken and averaged must exceed 20 . If a standard error of 0.02 L/s is acceptable then 5Q2 measurements must be taken and averaged. If gravity filling is not possible then the number, n, of repeat pumped container measurement required is given by: where: is the 100 m section leakage is the volume filling time is the standard error of volume measurementZ is the standard normal variateK is a coefficient dependent on physical measurement conditions Based on analysis of field data an indicative coefficient of variation of volume measurement is ~0.05.

Jan 1, 2008

The development of Mount Isa Mines Limited power supply is traced through the history of the mine operations. As would be expected, growth of the power supply system follows closely the increase in mine output, although it will be seen that total kWh. produced per ton milled shows a considerable reduction in later years when the mine output showed a more rapid rate of increase. That this reduction is not more marked is possibly due to the increased community and Shire Council power usage per head of population.INTRODUCTIONThe geographical position of Mount lsa, far from any large regional power supply Authority, dictated the policy that the Company be responsible for the production and suppiy of all power required for the plant operation. The Company also, in November 1937, accepted responsibility for the supply of a part of the power requirements of the township of Mount Isa. The history of power supply to the Mine may be divided into several phases.1. The supply Of lighting and power during the first plant construction period 1929-1931.2. The construction of the first section of the Mines Power Station, comprising Nos. 1 and 2 turbo alternators and boilers.3. The addition of No. 3 turbo alternator and boiler.4. The addition of No. 4 turbo alternator and boiler.5. The addition of No. 5 boiler.6. The addition of a. 2 turbo blowers for air supply to the Copper Smelter converters; b. 1 turbo blower for air supply to the L.ead Smelter; c. 2 turbo compressors for compressed air supply to the Mine and surface plant.

Jan 1, 1961

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012

By J Coveney, A Rich, D Grimsey, J Wood, S Creedy

In 2021, BHP and Metso examined processing of high-MgO nickel sulfide concentrates using Metso’s Ausmelt Top-Submerged-Lance (TSL) technology. Test work was conducted in Metso’s pilot test work facility in Dandenong, Australia to explore operability of the SiO2-FeO-MgO-CaO-NiO slag system across a wide range of compositions, temperatures and bath oxygen potentials. Pilot-scale testing aimed to define slag ‘operability limits’, representing the lowest bath temperature at which stable process and equipment operation could be maintained. This work was supported by FactSage™, version 8.2 (by Thermfact/CRCT and GTT-Technologies) thermodynamic modelling, slag viscosity measurements, physical characterisation of quenched slag samples performed by the University of Queensland and benchmarking of commercial-scale TSL nickel smelting operations. A wide range of slag compositions were examined, with Fe/SiO2 ratios varying from 0.4–1.1, CaO content from 0.8–7.0 wt per cent and MgO content from 6–19 wt per cent. Slag SiO2/MgO ratio, wt per cent CaO and matte grade were found to have the greatest impacts on identified operability limits. Operability limits were found to be influenced by both the solids content in slag and viscosity of the remaining liquid slag phase, with the relative contribution of these parameters heavily influenced by the slag composition. In the majority of trials, limits were defined by a theoretical solids content of 40–50 per cent, however in trials with a low Fe/SiO2 ratio and/or low wt per cent CaO, limits were characterised by a much lower solids content due to the increased effect of the liquid slag viscosity in determining the behaviour of these slags. The test work highlighted inherent flexibility of the Ausmelt TSL process to operate across a wide slag range of slag compositions and recover from process disturbances without an interruption to feeding. The trials also demonstrated the possibility for Ausmelt TSL technology to process concentrates with an Fe/MgO ratio as low as 1.4, which has important implications to the commercial-scale processing of high MgO feeds. Arsenic rejection across the trials was very good, with only 30 per cent of arsenic in the feed inputs reporting to the matte phase. Such high levels of arsenic removal provide the Ausmelt TSL process with a notable advantage over alternative smelting technologies.

Aug 21, 2024

By J Player, P Evans, G Sweby

Achieving quick underground access after the completion of an open pit mine can be critical to maintaining project value and ensuring regular ore feed to the mill. This paper outlines the design and construction for two portals in an active open pit to commence underground development quickly whilst installing appropriate ground control to maintain long term access in an uncertain setting. Implementation of the portal designs was complicated by the change in underground design from hangingwall access to footwall access late in the life of the open pit due to preferable ground conditions. The portal locations did not have easy access for ground support installation integrated into the pit design due to the timing of the underground design changes. Practical implementation of the ground support systems subsequently became a key part of the project. Intact rock strength, rock mass characteristics, gradational weathering / alteration profile and structural information were modelled against pit displacement monitoring as the basis from which the portals were located and ground support schemes designed. Conditions around one of the portals necessitated numerical modelling to estimate the appropriate level of ground control for long term stability. The design was completed whilst the open pit was actively on-going and the portal areas not entirely exposed. The rock mass assessment and analysis for the two portals indicated different ground support scheme capacities would be required. The expected level of control for one of the portals also necessitated the use of monitoring with extensometers and load cells to ensure the rock mass response and ground support scheme performed as planned. Construction of the portals demonstrates the benefit of a considered design process, a plan which allows practical installation of ground support schemes where access is limited, the benefit of ongoing monitoring to ensure performance remains within design limits and the challenges involved working within an active pit with limited floor space.

Mar 15, 2021

By Y D. Jeon, K S. Kim, C-H Eom, C M. Yoon

The carbon neutrality continues to require reduction of carbon usage in ironmaking and steelmaking processes. Specially, it is expected that the hot metal ratio (HMR) in the steelmaking process should be reduced essentially. Unfortunately, the reduction of the HMR in converter can bring about poor environment for nitrogen removal from molten Fe. From this situation, nitrogen prediction model has been developed to understand the fundamental of behaviour of nitrogen and quantitatively interpret its content changes in the converter process. Thermodynamic and kinetic approaches were improved based on existing mathematical model and attempted to predict nitrogen content in realtime by combining process data. In present study, heat supply from the oxidation (mainly carbon and silicon) and CO evolution in the converter are considered, and scrap melting due to the heat transfer from the molten Fe to the solid scrap charged in the converter also be considered.

Aug 21, 2024

By S Liu, N M. Rana, A Take, N Ghahramani, D Clohan, S McDougall, S G. Evans, H J. Chen

Tailings dam breaches have caused significant life loss, social, economic and environmental damage in recent years. The term "tailings-flow" refers to various forms of tailings outflow movement resulting from the breach of a tailings dam. These flows, comprising a mixture of tailings, water and dam materials, can take different forms, ranging from a debris flood to a flowslide, and can travel long distances and impact large areas. The inundation extents depend on the failure mechanism, tailings dam height, total released volume, sediment concentration (associated with the rheological behaviour of the flow) and downstream conditions (including topography, land cover and presence of a water body). Numerical runout modelling of tailings dam breaches is important for predicting the dynamics and extent of tailings-flows, which are crucial steps in tailings dam consequence analysis and risk management. This paper presents a comparison of numerical simulations of the 1994 Merriespruit tailings dam breach using three numerical models: DAN3D, FLO-2D and MADflow3D. Using compiled site condition information and data from the literature and public domain, model performance was evaluated primarily based on comparisons between the observed and simulated inundation extents. The main purpose of this preliminary model benchmarking exercise was to help us evaluate the capabilities and limitations of each model, and to identify opportunities for future model improvements as part of a broader research initiative known as CanBreach. This exercise also highlights the inherent complexity of tailings-flows and the importance of using judgement to interpret model input and results.

Jul 1, 2021

By R Ballantyne, M Adams

Time Usage Models, used as a basis for calculating performance indicators for mobile mining equipment, have developed from very simple to very sophisticated models. This development has paralleled the increased collection and analysis of production data that itself has been enabled by the evolution of underground voice and data communications along with the relevant information systems. A Time Usage Model divides the hours that equipment is (or is not) used into standard components, by a hierarchical breakdown, so that measures of productivity can be used to compare performance of both people and equipment. The calculation of equipment availability, and thus the underlying Time Usage Model, has always been an extremely emotive topic as different groups use time usage information for different purposes. The direct link between measuring performance Key Performance Indicators (KPI) calculated from these models and employee rewards impacts upon the workforce. This paper discusses the conflict in use by various stakeholders and proposes ways to address some of the more contentious issues each supported by case studies. The simple status code functionality used by early systems has proven inadequate, leading to the evolution of “work-arounds”. These workarounds have become the norm and unfortunately have become embedded in the next generation of models and the information systems that incorporate them. This paper contends that the industry should stop building Time Usage Models to accommodate shortcomings in proprietary systems, but rather collaborate with suppliers to develop innovative methods to deal with the fundamental requirements. There are many points of differentiation that are not clear-cut. Pitfalls are discussed as well as threats to success. A framework of rules is developed as guidelines for how a Time Usage Model should be developed and applied. This will hopefully stimulate the on-going discussion as to how Equipment Availability and other components of the model should be calculated.

Mar 15, 2021

By R Atmuri, W Liang, R Prasad, Y Liu, E Wingate

Yellow phosphorus (YP) has been commercially produced since the 1920s. First in the USA by the Tennessee Valley Authority (TVA), next in Russian (Kazakhstan) in the 1950s, and finally in China in the late 1970s and early 1980s. There are operations in Vietnam and Sarawak on a smaller scale. YP has become very in vogue due to its use in the production of lithium iron phosphate battery cathode precursor materials by the Chinese and other western battery manufacturers. The YP is also used to produce purified phosphoric acid and higher grades of acid using a thermal oxidation process after smelting. This paper will look at the basics of the smelting including slag chemistry, alloy chemistry and offgas chemistry. The paper will look at the design of the furnaces used in the YP production process as well as the downstream recovery of phosphorus from the smelter off-gas stream to YP. The next part of the discussion will focus on the operations of a YP smelter with regards to control of the furnace to optimise phosphorus recovery to YP. Will discuss tapping cycles for alloy and slag with a view to optimal phosphorus recovery. The discussion will close out with a review of operational challenges in the smelter and a brief description of the downstream conversion of YP to high purity phosphoric acid.

Aug 21, 2024

By T Higuchi, T Yamamoto, K Takehara

Iron ore fines are used as raw materials for sintered ore for blast furnaces in the world. Since the production and quality of sintered ore have a great influence on the stable operation of a blast furnace, many technologies were developed for controlling the heat profile in the sintering machine, which largely affect the sintered ore properties. In particular, the influence of oxygen in the suction gas, which plays an important role in combustion, was investigated over the years. It is known that increasing the oxygen ratio by about 30 per cent not only significantly improves the combustion rate, but it also increases the strength and yield of sintered ore. However, the details of the mechanism for improving these qualities are unknown. In this study, we investigated the influence of oxygen enrichment at higher ratios (O2: 21–40 per cent) and tried to understand the sintering behaviour enhanced by oxygen. The effect of oxygen enrichment on sintered ore quality and the heat profile were evaluated by sintering tests using a quartz glass pot. From the results, sintered ore yield had a maximum value for O2 = 30 per cent, but strength was increased for O2 = 40 per cent. From heat pattern analysis, it is clear that the high temperature holding time also reached a maximum at O2 = 30 per cent. Furthermore, we found that with increased oxygen ratio, the combustion speed (flame front speed) was increased, but the area of combustion was enlarged. It is considered that there could be a maximum oxygen ratio value for the yield from the balance of these positive and negative effects on high temperature holding time. To clarify the reason for strength improvement, thermodynamic calculations were performed and it was found that melting behaviour could be improved by changing the oxygen ratio.

Sep 18, 2023