Search Documents

By S Whitton, W Wimmler, L Wimmler

“Given the increasing scrutiny of the mining industry and its relatively poor record with regards to mine tailings management, increased requirements to minimise water usage (often accompanied by very high costs of water) and the need to demonstrate achievable long-term closure strategies, it is likely that the option of a filtered tailings system will need to be considered in many operations in future.” (Australian Centre for Geomechanics, 2018). Given such a statement as a conference introduction, it is only appropriate that a range of potential technologies are investigated and compared, to create awareness for even underrated but appropriate technologies. The advantages and disadvantages of all technologies need to be considered and analysed. Suppliers are swift to promote their technologies advantages; however aspects of sustainability are not always fully understood. Perhaps a combination of two filtration technologies is appropriate. This paper delves into the technical details, good or bad, of four mechanical dewatering technologies in tailings dewatering and provides insight on an undervalued and, in the author’s opinion, young technology – the screw press.

Jul 1, 2021

By K Williams, M Pender, T Honeyands, T Krull, D McCallum, R Holmes, R Orense

Bulk cargoes, including iron ore fines, must be shipped according to the rules agreed by the member states of the International Maritime Organization (IMO). One critical safety measure is the transportable moisture limit (T?ML) required for Group A cargoes (cargoes that may liquefy). A number of shipping incidents involving iron ore fines from India, where liquefaction of the cargo was suspected to be the cause, have brought the issue of iron ore fines T?ML into the spotlight. Extensive research has been undertaken by the major iron ore producers from Australia and Brazil to support the IMO in developing regulations for the shipment of iron ore fines. To this end, iron ore companies sponsored the AMIRA P1097 project to establish a modified T?ML test approach specific to iron ore fines. The project was undertaken by TUNRA Bulk Solids, CSIRO’s Centre for Bulk Solids and Particulate Technology and the University of Auckland, with project leadership provided by Creative Process Innovation. This program of work supported test work findings from the IMO Iron Ore Technical Working Group, which reported its findings in September 2013.The purpose of this paper is to present the major research findings from the AMIRA P1097 project, which includes a review of the original T?ML methods, highlights of the research that supported the new iron ore fines T?ML method and an outline of current iron ore T?ML requirements.CITATION:Williams, K, Honeyands, T, Holmes, R, Orense, R, Roberts, A, Pender, M, McCallum, D and Krull, T, 2015. Maritime bulk cargo transportable moisture limit requirements for iron ore shipments, in Proceedings Iron Ore 2015, pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L L. Kuhar

The AMIRA International P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project is an interdisciplinary research collaboration between 17 global mineral companies and four research organisations aimed at providing support for the emerging industry trend of geometallurgy. The main aim of the project is to develop predictive geometallurgical indices which can be incorporated into a resource block model to maximise the commercial value of an orebody and to minimise the social and environmental impact of mining operations.Researchers at the Parker Centre/CSIRO have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. The focus of the small-scale leach tests has been to determine the leach index (relative indication of leach performance), recovery, impurity deportment, reagent consumption, effect of size/degree of liberation and mineralogy of samples for their relative ranking. Predictive tests for heap leach hydrology (related to agglomerate characteristics) and slurry rheological behaviour are also being developed.

Sep 5, 2011

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974

By A Giblett, B Putland

This paper provides a simple guiding framework for grinding circuit optimisation, focussing on common themes in past optimisation success stories, the conditions for success and techniques that can be employed to identify and define opportunities. Many significant grinding circuit improvements have been reported for operating plants, based on recurring themes such as the optimisation of mill feed size, mill liner design, process control, critical size, grinding media and classification. The paper condenses these experiences into a set of simple questions for the operator to ask, and provides guidance towards identifying and achieving the optimisation goals.CITATION:Giblett, A and Putland, B, 2018. The basics of grinding circuit optimisation, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

By M D. Melville, B C. T Macdonald, J Dixon

The acidic and metal rich waters that are generated from acid sulfate soil (ASS) drainage can have damaging impacts upon ecosystems. The most obvious impact has been the discolouration of water and occasional fish kills. ASSÆs produce these acidic and metal rich waters when pyrite in soil is oxidised. Land management techniques are an essential long-term requirement to minimise the amount of pyrite oxidation. Acidic water that cannot be prevented through land management can be neutralised by other techniques. Powdered lime is the most common material in agriculture that is applied directly to soils and waters. Powdered lime can be expensive and if applied dry it may aggregate. Since the aggregated particles of lime are larger they could sink rapidly in the water column and not react. In waters with high concentrations of dissolved iron and aluminium the lime particles may become coated with a metal oxy-hydroxide precipitate, which will decrease its reactivity. A unique lime-dispensing machine, the Waterways Lime Spreader, has been developed to neutralise acidic waterways. The Waterways Lime Spreader can produce a solution rich in fine lime from larger limestone fragments. The current size of the machine means only 3.5 grams per second of limestone can be emitted. This output will neutralise low acidity waters, however, for high acidity waters the time for neutralisation can be long. More reactive chemicals such as hydrated lime or increasing the size of the machine will reduce this neutralisation time. The Waterways Lime Spreader is also capable of producing slurry mixtures if powdered materials are required. Trials with the Waterways Lime Spreader were undertaken in part of the Clothiers Creek catchment located in northeast NSW, Australia. A small drain with a water volume of 4 m3 was neutralised with crushed limestone to pH 6.9 from an initial pH of 2.6 and an acidity of 902 mg/L CaCO3 in 160 minutes. In comparison a drain with a slightly larger volume of 6 m3 that had an initial pH of 3.2 and an acidity of 753 mg/L CaCO3 was neutralised with hydrated lime to pH 11.8 in five minutes. The Waterways Lime Spreader has been used successfully to neutralise water from acid sulfate soils. It is expected that future applications of the machine may be for the neutralisation of acid rock drainage or acidified lakes.

Jan 1, 2003

By N Cusworth, W R. Mackenzie

"In 2007, the authors presented a framework for the conduct of resource project feasibility studies and provided guidance on minimum standards and best practice (Mackenzie and Cusworth, 2007).This paper will present the authors’ observations in relation to feasibility studies undertaken to support investments made during the unprecedented period of resource project capital investment since 2007. It will also provide comments on general trends in the mining industry’s approach to project assessment and update recommendations on best practice.CITATION:Mackenzie, W R and Cusworth, N, 2016. The use and abuse of feasibility studies – has anything changed?, in Proceedings Project Evaluation 2016, pp 133–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C Katonga

Mindola mine is currently the deepest mine in the Zambian copper belt. Stoping is currently active to 1330 m below surface with long range plans indicating future production from 1590 m level. The orebody is tabular and dips between 55o to vertical. The thickness varies from 8 to 14 m. The vertical crater retreat method of mining was first introduced at Mindola mine in the late-1980s following several trials that helped define the design criteria for its application. Over the last ten years the method has been continually modified to improve safety and maximise ore production. For example, due to the weakness of some rock units within the orebody formation and the instability of the hanging wall, the last VCR slices are usually between 8 - 10 m thick, and efforts are being made to strictly apply shrinkage method in order to reduce dilution. Recent advances in mining technology in the areas of equipment, blasting techniques, rock mechanics and materials handling have been employed to increase the overall productivity of the mine. Large down-the-hole machines capable of drilling 165 mm diameter blast holes, up to 80 m long are used in stoping. Each stope produces up to 20 000 tonnes of ore per month and can last for three months. Heavy systematic ground support of VCR development has significantly enhanced safety for mining crews and equipment. Crater mining has not only improved productivity and enhanced safety, but also overcome various problems associated with conventional sublevel open stoping previously employed at the mine. This paper discusses the technical and operational aspects of vertical crater retreat mining at Mindola mine during the last ten years. The changes in mining method are often accompanied by changes in mine design, blast design, mining equipment, ground support and operating practices.

Jan 1, 2000

By S S. Kanchibotla, E J. Sellers, L Julian, A Musunuri

Fume events in coalmines are typically associated with wet conditions, soft ground and deep holes. An ACARP research project used laboratory and field testing combined with literature reviews, numerical models and field investigations to characterise the influence of these conditions on the propensity for fume. This paper highlights the results for soft ground and wet conditions and proposes a proactive fume mitigation methodology. A simple numerical model is used to show how fume arises in soft rock that yields more under the loading of high-pressure, water-resistant explosive blends than for ANFO. The blends cool more rapidly after detonation into the lower temperature zone favourable for NO2 production. Low-pressure, high detonation temperature explosives are loaded or charged into soft ground. Water resistance must be considered because soft, faulted and fractured ground can lead to fume from degradation by water flow and non-ideal detonation of product in cracks.A suite of tests were developed to quantify ANFO and emulsion blend performance over time that can be carried out in a mobile laboratory on-site. Index tests such as viscosity measurement and water resistance in beakers are proposed to quantify long-term product performance because small components, such as surfactant, prill impurities and prill fines, contribute to inconsistent product performance. Water ingress experiments and detonation tests aligned with field investigations identified and characterised the role of groundwater in damaging ANFO and causing fume.Fume risk management is achieved using a proposed proactive fume mitigation methodology to characterise influences such as seasonal rain variation, groundwater flow hydrogeology, rock mass strength and structure well ahead of blast design. The design of blasts and selection of explosive products to consider expected conditions will reduce fume, improve efficiency in the mine and offer cost advantages.CITATION:Julian, L, Musunuri, A, Sellers, E J and Kanchibotla, S S, 2015. Mitigation of post-blast fume in soft ground and wet conditions, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

The base metal ore from the hanging wall of White's orebody at Rum Jungle, N.T., is composed of copper and oth.er sulphides in a rock described as a phyllite,.which consists essentially of micaceous minerals with a little graphite.Fast selective flotation was obtained in acid circuit below pH 3·5. In neutral or alkaline circuit flotation was generally slow and selectivity very poor due to the ready flotation of part of the sericite. However, it was found that fast selective flotation could be obtained in neutral or alkaline circuit by either of two treatment methods following pre-conditioning in acid circuit; firstly by decanting or filtering a substantial part of the circuit liquor, and secondly by neutralizing with soda ash or lime, providing the collector was added before neutralizing. Otherwise pre-conditioning with acid brought about no improvement whatever.To explain this behaviour, three possible reasons for the flotation of part of the sericite are examined. There is evidence that some sericite floats because of thin films of either sulphides or graphite, but it seems likely such particles will float under all the conditions investigated.On the other hand, if it is assumed that part of the sericite floats because it is activated by metallic ions derived from the circuit water, a reasonable explanation can be given for the variations in flotation behaviour.INTRODUCTIONWhite's uranium orebody at Rum Jungle, N.T., sixty miles south of Darwin, is mined and treated by Territory Enterprises Pty. Ltd. (a subsidiary of Consolidated Zinc Pty. Ltd.), who are managers of the Rum Jungle project on behalf of the Australian Commonwealth Government.This ore contains a significant quantity of copper sulphides, and a flotation plant recovers a copper concentrate from the tailing remaining after the uranium has been extracted.In contact with the hanging wall of the uranium-copper orebody, a further mass of non-uraniferous sulphide ore occurs, and the present paper relates to the behaviour in flotation of this base metal ore.

Jan 1, 1959

By A M. Lechner, S Arnold, M J. Gillespie, P D. Erskine, D R. Mulligan, A T. Fletcher, A Gordon

Mine ecological monitoring schemes are often conducted only to address compliance and in some cases do not have the sufficient statistical power or understanding of ecological systems to assess, quantitatively, the meeting of rehabilitation targets or mine impacts. Monitoring schemes for rehabilitation commonly rely on analogue sites or premining baselines (reference sites) to assess whether rehabilitation sites are ecologically similar and thus successfully rehabilitated. In the case of monitoring for mine impacts, if the impacted sites diverge from reference data, the site is considered to be impacted. Fundamental to any monitoring scheme is testing the sampling design to ensure that it can detect these differences if they are present through adequate sample sizes (ie statistical power). However, a good understanding of the ecological system is required to ensure that differences detected are ecologically significant. Modelling ecosystem properties can provide a quantitative understanding of how ecosystems change over time and space, in response to natural environmental variations and thus aid in determining significant ecological differences. Furthermore, modelling methods can be used to predict future ecosystem states. Within the ecological literature, guidelines for robust statistical monitoring designs and modelling methods exist but are not routinely being used in the mining industry. This paper uses simple examples to discuss: problems with current compliance monitoring methods; importance of robust statistical techniques; and how modelling can assist rehabilitation assessment and guide monitoring schemes. The aim of this paper is to describe general monitoring and modelling methods that could be potentially used for mine site monitoring and closure assessment. These methods are often considered by mining companies as an extra expense that provide little practical benefit, and the domain of academia; however, engaging these methods may be more cost-effective in the long-run than conducting untargeted monitoring schemes that give no confidence to regulators on whether rehabilitation criteria have been met. Furthermore, monitoring programs in mining contexts provide a good opportunity to better understand long-term ecological patterns and test the application of more rigorous modelling approaches as the life of many mines tends to be greater than ten years.CITATION:Lechner, A M, Arnold, S, Fletcher, A T, Gordon, A, Erskine, P D, Gillespie, M J and Mulligan, D R, 2012. Embracing modern ecological methods - Monitoring and modelling for mine closure, not compliance, in Proceedings Life-of-Mine 2012 , pp 25-32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By S Sullivan

A recent review of resource reports lodged to statutory bodies found geological models with oversmoothed or unrealistic lithological boundaries, many of which do not represent geological appearance in the field, pit or underground drive. The underlying data is often too complex or messy to be incorporated into the resource model and is thus a simplification of reality, to the detriment of the mining operation and its shareholders. Volumes can be over- or underestimated and subsequent grade predictions can be misplaced, combining to cause over- or understatement in resource reporting to stakeholders and statutory authorities. Domain models can be improved with new modelling techniques such as machine learning. However, with poor data or improper use of machine learning techniques, the conclusions can be just as misleading as with current techniques. Machine learning rarely offers a single ‘right’ outcome, rather a range of possible outcomes from the data provided. But importantly it can take advantage of the full richness of data for more informed models. Machine learning also provides confidence in its predictions so that uncertainty in the resultant models can be quantified and passed through for risk assessment during mine planning and operation. This paper will discuss the factors accentuating complexity in deposit modelling: data diversity, structural controls, chemistry, data volumes, process workflows and external non-geological constraints. A case study illustrates the risk of reducing or ignoring complexity, which can result in an overly simplified geological model.

Mar 22, 2022

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C A. Chaves

During most of its history, the metallurgical industry has been seen as a source of pollution for the environment. However, during the second half of the 20th century, as the world environmental legislation became more protective and the global environmental conscience consolidated, this landscape began to change. Metallurgical activities have become increasingly related to the social and environmental impacts caused by human activities. With the adoption of environmental management in steel plants, there has been a significant change in steel-related activities which have begun to introduce modern plants, managed with environmental, social and productive efficiency. More and more, steel companies search for a decrease in negative impacts of their industrial operations on the environment, fitting them to the current environmental legislation and even increasing productivity and profitability. The steel industry has started to become a clean and more efficient industry. This work presents a case study of a sustainable steel plant project, located in an environmental preservation area. The project includes treatment and reuse of industrial liquid effluents, air emissions control, noise control, recycling, recovery and adequate waste management. It also incorporates production processes using clean technologies, capable of coproducing energy resources which may be used in the plant showing how is it possible to produce steel with environmental and social responsibility and even increase the enterpriseÆs profitability.

Jan 1, 2009

By T W. C Stambolie

Longwall mining is a form of underground mining and the principal extraction method for underground coal mining in Australia. The method is used in the mining of both thermal and metallurgical coal. The primary market for thermal longwall mines is that of the export market where price is governed against the Newcastle Thermal Benchmark index (globalCOAL, 2016).Australia’s thermal coal export outlook is considered moderate due to slower demand from major importing countries, as well as slowing domestic production. However, ‘Australia is projected to increase its share of world thermal coal exports and become the world’s largest exporter over the medium term as lower prices, increased domestic use and infrastructure constraints limit growth from other key suppliers’ (Office of the Chief Economist (OCE), 2016, pp 25, 58). On the contrary, and as a result of current global coal price trends, the basic economic principles of underground longwall coal mining are heavily stressed. From a life-of-mine perspective, influencing return on investment is at its greatest during project evaluation and execution. Appropriate and realistic economic assessment is paramount to ensuring the right outcomes are achieved under the current economic challenges.CITATION:Stambolie, T W C, 2016. Thermal coal industry – is longwall mining currently a life-of-mine option in Australia?, in Proceedings Life-of-Mine 2016 Conference, pp 57–61 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By P York

The study commenced in October 2012, to understand the basic ecology of the spotted-tailed quoll (Dasyurus maculatus) and to confirm whether the species utilise previously mined land on the Mt Owen mine site that was rehabilitated in 1996 to 2011, as part of their home range. The spotted-tailed quoll is a widely distributed marsupial carnivore that is listed as rare or threatened in every state in which it occurs. The species is a forest-dependent marsupial carnivore that occupies a wide range of habitat types (Long and Nelson, 2004).The first part of the study involved trapping a spotted-tailed quoll and fitting the individual with a combined global positioning system / ultra high frequency (GPS/UHF) radio-transmitter collar (Telemetry Solution – Quantum 4000E). The benefit of the GPS/UHF collar is that it records locations (or fixes) at intervals programmed by the user. The UHF component allows the researcher to locate the individual at a frequent interval, and the Quantum 4000E also has a remote download function, enabling the GPS data stored in the collar to be wirelessly transmitted between the collar and researcher. The benefit of this new technology is that the animal does not need to be repeatedly captured to retrieve the GPS data.Daytime searches are also undertaken using the UHF receiver to locate the individual and locations of daytime denning and latrine sites. The location of each den site is recorded using a hand-held GPS. Data downloaded from the GPS collar is then imported and mapped using computer software program ARCGIS (geographic information system), to overlay the data points onto aerial photography.Results demonstrate that threatened species will utilise rehabilitation areas post mining. The data presented will be used to develop a greater understanding of threatened species ecology in and around rehabilitated areas, which will assist in the planning and design of native forest rehabilitation areas.CITATION:York, P, 2014. Mt Owen Mine spotted-tailed quoll study, in Proceedings Life-of-Mine 2014 , pp 591–596 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Whiteman P. C, Stacey G. S, Hunter G. D

Processing of lead-zinc and copper ores by Mount Isa Mines Limited produces large quantit- ies of concentrator tailings waste which is pumped as a slurry to special dams where the solids are allowed to settle and dry out. These areas are unattractive and show no signs of encroachment by plant life even though the surfaces of some dams have remained undisturbed for more than a decade. During 1970 Mount Isa Mines Limited commenced a long term research program in conjunction with the Department of Agriculture, University of Queensland to deter- mine possible methods of establishing a plant cover on this material. Research has defined the major factors limiting plant growth in the tailings medium. Modification of the edaphic conditions through fertilizer inputs, particularly of phosphorus and nitrogen, and alteration of "soil" physical properties by incorporation of mulching mater- ials, provided conditions which allowed plant growth. The outstanding "soil" amendment treatment was incorporation of fly ash, a waste product of the company's coal fired power stations. A range of crop and pasture species have been selected which have grown well with adequate irrigation under the amended conditions in the field. Further research is assessing a range of native plant species and agronomic techniques to provide a stable plant cover on the tailings dams.

Jan 1, 1974