Search Documents

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By M Uceda, E Guerra, Y Choi, J L. Shepherd

In this paper we describe the leaching characteristics of pure gold in thiosulfate solutions that contain a known chelator; meso-2,3-dimercaptosuccinic acid (DMSA). The interfacial and chemical characterisation of the system was accomplished using both electrochemical methods and inductively coupled plasma mass spectrometry (ICP-MS) analysis after pure gold samples were exposed to solutions composed of 65 mM Na2S2O3, 1 mM NaOH and a range of DMSA concentrations. In the absence of DMSA, cyclic voltammetry revealed the onset of thiosulfate mediated gold dissolution, the degree of which was reduced at more positive potentials due to the formation of oxidised thiosulfate products on the gold surface. The addition of small amounts of DMSA (<10 ¦M) to the electrolyte resulted in minor changes to the voltammograms indicating a subtle interaction of the additive with the gold surface that may improve leaching. However, at higher concentrations of DMSA (up to 100 ¦M), electrochemical evidence suggests the formation of new oxidation products in solution as well as the formation of more compact monolayers of DMSA on the surface, which contribute to partial repassivation of the surface. The influence of DMSA on thiosulfate leaching of pure gold electrodes at the open circuit potential for a period of 90 minutes was tested and the corresponding gold leaching performance evaluated with ICP-MS analysis. Our data shows that small amounts of DMSA (1 ¦M) doubled the amount of total gold in solution when compared to the same study in the absence of the additive. However, higher concentrations (5 ¦M DMSA) reduced the overall amount of dissolved gold. These results may point to a mechanism where small amounts of DMSA improve leaching by adsorbing onto the surface in a highly defective monolayer that partially blocks or disrupts the formation of passivation products caused by thiosulfate oxidation, but excess DMSA can limit the leaching process itself by forming too coherent a monolayer on the gold surface.CITATION:Uceda, M, Choi, Y, Shepherd, J L and Guerra, E, 2013. Investigating the influence of meso-2,3-dimercaptosuccinic acid on thiosulfate leaching of bulk gold electrodes, in Proceedings World Gold 2013 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Consultants in the mining industry have the opportunity to visit interesting deposits all over the world. Each deposit has its own set of challenges to face when it comes to defining and understanding the deposit geology and the economics to make it viable for extraction. Some of the challenges can include appropriate data capture, sampling techniques, structural characteristics, geochemistry, geophysics, lithology definition, and economic boundaries. It is essential that the practices used at each deposit (eg drilling, sampling, geological modelling, resource estimation etc) are documented and the results obtained are robust and defensible. The Competent Person is not always aware of instances where their resource estimation practices have not been substantiated. ‘You don’t know what you don’t know’ is a phrase frequently used during a mineral resource audit. Technical work to substantiate drilling, sampling, density, assaying, geological modelling and estimation processes is not always completed. Audited Competent Persons often comment: • ‘I was unaware that this was required.’ • ‘I have not had training in this area and do not know how to complete the checks required.’ • ‘This is how we’ve always done it.’ Examples of audits where it was found that geological practices were not substantiated are examined here. A discussion is included on why substantiation of these practices is important, and potential reasons as to why there are instances of unsubstantiated processes and practices are discussed.

Mar 22, 2022

By G R. Ballantyne, B Putland, I Lovatt, M Di Trento

The Tropicana Gold Mine, owned by AngloGold Ashanti Australia Ltd (70% owned and managed) and Independence Group NL (30%) is located 330 kilometres east-northeast of Kalgoorlie, Australia, in the newly developed Albany-Fraser Orogen. Following extensive feasibility studies, a high pressure grinding roll (HPGR)-ball milling circuit was selected based on the reduced power requirements and thus reduced operating expenses. The HPGR-ball mill circuit was estimated to require 75% of the energy of a standard semi-autogenous grinding (SAG) mill circuit. Even with an anticipated greater capital cost, the HPGR-ball mill circuit was found to give significantly better financial returns in all cases investigated in the feasibility study. A comparison between the specific energy requirements of the HPGR, crush and SAG based circuits (SABC) from the feasibility work was conducted and the HPGR circuit was found to be considerably more energy efficient. A survey was conducted and the efficiency of the HPGR was similar to both the overall circuit design and the HPGR laboratory results, reflecting the accuracy that is possible for design and operation of HPGR circuits.Between 2015 to 2016, the Tropicana circuit has achieved a 20% increase in throughput from 780 to 930 t/h, and this increase has been maintained in 2017. This improvement can largely be attributed to upgrades to material handling processes, increased HPGR speed and smaller HPGR screen apertures. The result of these changes has been to increase the ball mill capacity by increasing the breakage conducted by the HPGR.CITATION:Ballantyne, G R, Di Trento, M, Lovatt, I and Putland, B, 2017. Recent improvements in the milling circuit at Tropicana mine, in Proceedings MetPlant 2017, pp 73–83 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By R H. Knight

Production mine geology must be accurate and efficient in order to reduce risk and ensure that ore value and mining operation revenue are maximised. Present grade control practices are commonly based on outmoded and inaccurate 2D geological mapping techniques where spatial relationships are estimated by eye, sketched by hand and projected to arbitrary reference planes. The 3D mapping approach outlined in this paper integrates 3D photogrammetric imagery with implicit modelling techniques to enable more accurate grade control and reconciliation in underground mines. High-resolution stereo photographs are taken of daily ore development headings. Ore contacts are traced directly on a 2D face photo using a stylus and rugged tablet. Area-weighted face grades are estimated and calculated on mapped 2D face planes. In the office, a 3D photorealistic mesh is processed and georeferenced. 2D face mapping data is transformed into its actual 3D location and true 3D mine mapping is performed by digitising oriented 3D polylines representing ore contacts and other geological features directly onto the image surface. Three-dimensional spatial relationships are fixed, eliminating the projection error of traditional 2D methods. Ore envelope and waste solids are modelled within the closed, drift-round mesh. Volume-weighted ore envelope and round grades, as well as round volume and tonnage, are calculated. Ore/waste classifications, grade, tonnage and per cent dilution are quantified per round, visually assessed in 3D and reconciled with short- and long-term models on a daily basis. Updated geological continuity models provide geological guidance in development headings under geological control and accurate 3D structural and form-line mapping improves definition drilling and stope planning. Three-dimensional imagery provides a permanent detailed survey and geological record of mine workings that can be revisited virtually to reinterpret geological ore controls in light of new observations and insights. In addition images can be used to monitor daily production performance, create training scenarios for miners, engineers and geologists and prepare management presentations. This approach adds value to underground mines by improving the accuracy and efficiency of mine geology practices. The method is particularly effective in mines with visually distinct and geometrically complex orebodies, such as those in the Balmat zinc mine located in New York State, USA, which are used to illustrate the method.CITATION:Knight, R H, 2017. 3D mine mapping – improving grade control and reconciliation in underground mines using photogrammetric imagery and implicit modelling techniques, in Proceedings Tenth International Mining Geology Conference 2017, pp 203–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

In presenting the paper, Mr. Davey quoted subsequent work which yielded k, at miscibility gap composition, of about 50.We can confirm the authors' findings for k j 300 for nearly pure tin to k 2 about 50 (average 47) from our own experience and from repeat experiments on materials described by the authors, at 1150°C.During laboratory-scale trials we also found confirmation of the authors' view that it is more difficult to reach equilibrium from the high-iron (in slag) side than from the low-iron (high-tin) side. Working from the high-iron side tends to yield results that point to a high k, leading to optimistic values of iron/tin ratio in final slags. In practice the smelting of a tin concentrate, unless it is exceptionally low in tin and high in iron, must yield initially a tin-rich slag and therefore equilibrium can only be reached from the "tinny" side.

Jan 1, 1967

Alfred Nobel first invented a practical detonator in 1863 and then the blasting cap in 1865. At that time the detonator was used on the end of a length of safety fuse to initiate nitroglycerine-based explosives. Since then the detonator has gone through a number of changes. The instantaneous electric detonator was the first to allow remote firing. The electric delay detonator followed and allowed for timing between holes. In the mid 1970s the NONEL« Tube was invented. This tube combined with NONEL« detonators meant that many of the safety issues, such as stray current and radio frequency, associated with electric delay detonators were eliminated. This system gave the mining industry a reliable and fairly accurate system with which to detonate shots of any size. Since the early 1980s a large amount of research and development work has been done around the world to create a more accurate detonator for the mining and quarrying industry. After years of research, electronic detonators have emerged as the most accurate and precise initiation system available to the mining and quarry industry today. Electronics provide the user with millisecond timing accuracy. The improved level of timing control allows operations to improve fragmentation, throw and reduce vibration levels. There are now a number of different electronic detonator suppliers on the market today. In 2004 Dyno Nobel formed a joint venture called DetNet with AECI. DetNet has a suite of electronic detonators: DigiDet«, HotShot« and QuickShot«. This paper will focus on the HotShot« system, the first of the three new initiation systems to be released to the market in Australia by Dyno Nobel.

Jan 1, 2005

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By R Fanni, D Reid, M Kulessa

Recent updates to Australian industry guidelines emphasise the importance of the assessment of liquefaction potential of tailings. This includes assessment of the cyclic liquefaction potential, and the post-seismic strength of tailings expected to undergo strength loss from seismic loading. Despite this increase in focus, a relatively small number of Australian tailings appear to have been characterised through cyclic and post-cyclic testing. This paper presents the cyclic characterisation of four Australian tailings, consisting of iron ore, lateritic nickel, vanadium and bauxite residue. Material was obtained either from surficial tube sampling or through remoulding samples in the laboratory from slurries. Testing consisted of monotonic, cyclic and post-cyclic tests for each material. For three of the materials, laboratory-scale shear vane testing was also performed to provide a comparison to post-cyclic strengths from direct simple shear.The results indicated cyclic resistances consistent with the results of other tailings presented in the literature. The lateritic nickel tailings provided the greatest cyclic resistance of the four materials tested, followed by the vanadium tailings. This was somewhat consistent with expectations for material behaviour based on index properties. Post-cyclic strengths were seen to decrease as cyclic strains increased, consistent with typical observations in the literature. Following significant cyclic straining, in some instances the post-cyclic strengths approached those obtained through residual shear vane testing. This provides further insight into the strain-dependent nature of post-cyclic strengths for some materials. The implications of these observations on the post-seismic stability condition are discussed.CITATION:Reid, D, Fanni, R and Kulessa, M, 2015. Cyclic and post-cyclic behaviour of four Australian tailings, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M Scoble, A Ostry, J Shandro

Mining companies are not ill-informed on the topic of community health. There have been a number of research studies that have illuminated community health issues associated with mining, especially in the western Canadian province of British Columbia. However, what is missing amongst the literature is the perspective of mine managers and mining executives on this topic. This is important as mine managers and executives face a number of issues related to community health and are under pressure to consider the topic in more detail. This paper presents results from an exploratory qualitative investigation based on grounded theory research techniques into current community health considerations from the perspectives of mine executives and mine managers working in Western Canada. Interviews were conducted between February and May 2012 with 11 mining versus ten mining executives and managers who represented operating mines or mining umbrella organisations in Western Canada. Participants report on general community health issues that are perceived to be important, the perceived role that the mining sector should play?in contributing to community health and how this differs in Western Canada as compared to locations abroad, and?risks companyÆs face in making community health contributions. This paper concludes by drawing attention to pressing health needs that are present in Northern, rural and Aboriginal populations in Western Canada and provides a platform for future research initiatives focused on improving the health and well-being of communities associated with the mining industry. CITATION:Shandro, J, Scoble, M and Ostry, A, 2012. Community health considerations from mining executives and managers in western Canada, in Proceedings International Mine Management 2012, pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By T Blyth, D Holden, N Archibald, S Huffadi

The Morning Star mine is owned by Hill 50 Gold NL. Gold is hosted in quartz-carbonate ¦stibnite ¦molybdenite veins that occur in a series of deformed, altered and metamorphosed mafic volcanics with subordinate sediments and felsic intrusive rocks. The irregular gold distribution and its relationship to structure and alteration intensity makes the definition of stoping limits difficult. Understanding the structural evolution of the orebodies and the contemporaneous and later structures that affect the orebodies has been very useful in this context. This paper reports on a detailed mapping exercise (as part of a more extensive and on-going investigation) and the integration of this mapping with other geological and grade control data in a 3D modelling environment to provide an expanded basis for stope design. Three types of mineralised zones can be discriminated based on the morphology of the veins within. They are:those associated with strongly folded, thick veins (approximately 1 m thick eg 05 orebody); those comprising planar, boudinaged and some folded veins which consolidate to form tabular, steeply dipping bodies (eg 010 orebody); and zones containing the above vein types and thin, highly deformed veins within zones of intensely foliated country rock that result in localised, irregularly distributed high-grade gold zones (eg 02 orebody). The mineralised zones associated with thick folded veins are typically predictable over many tens of vertical metres. The second and third types of ore zone is generally less predictable. Detailed mapping and structural kinematic studies indicate all ore zone types are affected by progressive deformation involving strong strain partitioning. It is interpreted that high strain zones, recognisable by intense foliation development and highly deformed veins, are the latest stage of a progressive deformation which approximates bulk flattening. Structural controls on mineralisation can be defined at two different scales.Regional scale folding has deformed a sequence of mafic volcanics with interlayered sediments and felsic intrusives. Initial geometry of felsic bodies relative to orientation of the primary lithological layering and the bulk shortening direction is interpreted to be critical for initiation and development of strongly dilatant zones within this package of rocks, and Local scale dilation is evidenced by development of several vein sets whose range in orientations and opposed vergence relationships suggest a pre-folding origin comprising both extensional and hybrid shear-extensional types. Continued deformation resulted in folding of these veins with strong strain partitioning. Major vein packages are closely spatially associated with the felsic/mafic contact and an interpreted early structure which appears to have partitioned early dilation. This structure is now obscured by strong deformation but is currently represented by a zone of planar veins.

Jan 1, 2000

By D Roldpo, M Vidigal, J F. C L Costa

The local cumulative distribution function (lcdf) of a selective mine unit (SMU) can be estimated by conditional simulations using the statistics derived from the sample points, generating multiple equally probable scenarios. Conditional simulations permit the evaluation of the lcdf at any support, taking into account the spatial variability, ie the variogram, and the two statistical moments, mean and variance, of the conditioning samples. The SMU ore losses and dilution depend on the mining method and mining equipment selectiveness that, in its turn, depends on the predicted block size. A new approach to predict ore loss and dilution was developed in this study. Monte Carlo simulation is used to randomly generate a grade value derived from the lcdf at the mining stage (Zs_mc(t)) in order to make a decision about the SMU destination, ie processing plant (ORE) or waste dump (WASTE). If Zs_mc(t) is lower or equal to the cut-off (Z_cut-off) the block is ORE and, conversely, if Zs_mc(t) is higher than the cut-off (Z_cut-off) the block is WASTE. Considering these binary destinations ORE/WASTE, at the mining time t, and combining each realisation of the simulated random function Zcs_i (X), there are four possibilities for each SMU simulated value: 1. the block was simulated as ore and is actually ore (OO), 2. the block was simulated as ore and is actually waste (OW),3. the block was simulated as waste and is actually ore (WO), and 4. the block was simulated as waste and is actually waste (WW).The dilution factor is given by possibility 3 (WO), while the ore loss factor is represented by possibility 2 (OW). These results comprise the classical classification and reconciliation plots used in the mining industry. The new procedure proposed in this paper is based on the use of all the equally probable simulations to define the ore loss and dilution factors. An application of this methodology was carried out at Vale's iron mine in Brazil. The grade of silica was simulated and 50 multiple equally probable 3D models were generated. The mean and the standard deviation of the ore tonnage (OO + WO) for the 50 realisations, was 233 Mt and 0.5 Mt, respectively. The mean grade increased for the diluted ore (OO + WO) as well as their respective coefficient of variation (CV). The CV increases from 62 per cent in the undiluted ore (OO), to 101 per cent in the ore, considering the dilution factor (OO + WO). The mean ore loss (OW) was 10 Mt and the waste tonnage dilution (WO) was 9 Mt.

Jan 1, 2009

By M P. Sandy, J B. Albrecht

"Narrow vein mining can be loosely defined as mining operations involving orebodies with a true thickness of less than 4 m. Some authors have limited the term to steeper-dipping orebodies where the ore will rill under gravity. However, ænarrow veinÆ can also legitimately refer to some of the flatter orebodies, such as many of the platinum, chrome and gold deposits of Southern Africa, and several in Australasia including Bullen (at Norseman), Sunrise Dam, Telfer (Patterson, 1993) and the famous æflatmakesÆ at the Emperor Gold Mine in Fiji (Gordon and Harmse, 1993). Where the orebody dip is less than about 40¦ additional effort is usually required to remove the broken ore, including the use of scrapers, hydraulic monitors or remote-operated excavators (Tombs, Buckingham and Hancock, 2008).Working in such narrow orebodies presents particular operational and geomechanics challenges. A range of mining methods have been developed or adapted to exploit narrow orebodies including:cut-and-fill,narrow vein bench or longhole stoping,Alimak stoping,shrinkage stoping, and methods for shallow dipping orebodies (including Airleg and mechanised methods).The paper discusses some of the advantages and disadvantages of each method with a focus on geotechnical aspects including mining sequence options, stress management, ground support requirements, dilution and recovery.CITATION:Sandy, M P and Albrecht, J B, 2012. An overview of geotechnical issues in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 185-194 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By R-H Yoon

A turbulent flotation model has been developed by considering the subprocesses of collision, attachment, detachment, and froth recovery. AbrahamsonÆs model (1975) of infinite Stokes number is used to model collision, while the attachment and detachment subprocesses are modelled by considering the kinetic energies required to overcome the energy barriers and the work of adhesion, respectively. The energy barriers are determined by considering various surface forces, including electrostatic, dispersion and hydrophobic forces, while the kinetic energies are determined from the particle velocities at close separation distances from air bubbles. The latter has been determined by modifying the turbulent root-mean-square (RMS) velocities of Liepe and Moeckel (1976) and Schubert (1999) in view of a lubrication theory. In calculating the RMS velocities, it is assumed that a flotation cell is subdivided into low and high energy dissipation zones. The model predictions made by varying various hydrodynamic and surface chemistry parameters are consistent with flotation practice.

Jan 1, 2005

By R Millar

A frequent challenge in mine water management and mine design is estimation of precipitation and extreme rainfall given a short record of site meteorological data. For remote mine projects, typically only a few years of rainfall data are available, which is far too short for estimation of design rainfall event, such as the 1-in-100 year storm. A frequency-paired approach is presented for comparing daily precipitation records from a mine site with a long-term regional station and provides the basis to transpose the long-term record to the mine site. This allows a long-term synthetic precipitation record to be developed for the mine site that can be used to undertake site water balance studies, determine pond storage requirements, assess water supply options and address other surface water management issues. Conventional approaches are based on chronologically-paired data and when applied to daily data generally yield poor correlations between stations. In the frequency-pairing approach, statistical distributions (two-parameter gamma distribution) are fit to daily data from two stations and used to calculate daily and extreme precipitation values for the short-term site (which is typically a mine or other project site). The method is demonstrated using data from two meteorological stations located along the south coast of British Columbia, Canada. Use of a fitted two-parameter gamma distribution (or other distribution) provides a sound theoretical approach to comparing precipitation data from two sites and the basis for transposing a long-term record to generate synthetic precipitation series and extreme rainfall values at mine sites.CITATION:Millar, R, 2013. A statistical approach for deriving project design rainfall, in Proceedings Water in Mining 2013 , pp 273-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By C J. Pitzer

The prevention of fatal risks is a key objective for the global resources industry, especially considering poor performance with regard to fatality rate reduction and the continued occurrence of mine disasters globally. However, the industry has a credible history, over several decades, of the development and deployment management systems to control potential Serious Injury, Fatal and Catastrophic (P-SIFC) risks. While these systems have had a significant impact on the thinking and approaches to the prevention of fatal risks, fatal accident rates have not shown the desired reduction. Recent fatal and serious injury events in Australia have led to the establishment of several enquiries to further identify improvements that could be considered. Globally, fatal accident rates remain stubbornly high or plateaued in many jurisdictions, and several catastrophic events have occurred, such as tailing dams disasters in Brazil and South Africa, and the recent coalmine disaster in Turkey. Apart from the apparent lack of progress, it is evident that the deployment of critical risk systems has introduced more bureaucracy, slower response systems and additional burdens on already overloaded middle and supervisory levels of management. Organisations are rarely able to effectively tap into the risk source of risk knowledge of the frontline worker and supervisor, for various reasons discussed in this paper. To establish a valid and valuable channel of critical risk information flow from the frontline employee, Debmarine Namibia instigated the development and deployment of a system called SafeSENTRY, where the focus is on the ‘dynamic identification of dynamic risks’. This paper outlines the system, the principles of the design, the range of risk metrics that can be derived from the observations of the frontline operators, and demonstrates how a range of posited shortcomings in critical risk management is addressed how features of the High Reliability Organization (HRO) have been developed.

Mar 29, 2023