Search Documents

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

THE tensile and notch tensile ductile-to-brittle transition characteristics of several refractory metals and alloys have been well documented.1-3 Electron-beam melted tantalum and columbium have been shown to retain excellent ductility at very low temperatures. Some indications of brittle behavior (low ductility and cleavage fracture) were observed with columbium tested at -253oC, but no similar effects were noticed with tantalum. Increasing the interstitial oxygen content in these two materials resulted in the detection of indications of brittle behavior at higher temperatures, although good ductility was retained in both bases at -196°C when they contained about 1 at. pet 0. Detailed descriptions of the impact transition behavior of these two materials at various purity levels have not been available. This technical note describes the effect of interstitial oxygen on the impact properties of wrought, fibered tantalum and columbium and compares the transition behavior to the previously determined tensile transition characteristics. Tantalum and columbium impact specimens with three different interstitial oxygen levels indicated in Table I were tested at temperatures ranging from -196o to 300°C. Oxygen additions were made to 1/2-in.-diam bars of electron-beam melted material in a Seiverts Apparatus. The oxygenated bars were then homogenization-annealed to obtain uniform cross-section hardnesses and swaged to

Jan 1, 1964

By Charteris A. Stewart

The following scanty notes on the Roumanian oil-region may serve as an introduction to more detailed future study and description. The Roumanian oil-belt follows the outer edge of the sweep of the Carpathian mountains, and may, in a broad sense, be regarded as a prolongation of the Galician belt. It is distributed over a tract of country from 300 to 400 miles in length, with a width of from 15 to 20 miles, and is believed to cover an area of at least 20,000 hectares (49,420 acres). The governmerit claims that 16,000 to 17,000 hectares of its land is petroliferous. The primary deposits of petroleum arc considered to be in the Paleogene (Oligocene) and the Neogene (the salines of the Miocene) formations. Most of the other repositories, especially those of Muntenie, are only secondary, the petroleum there having been introduced by the orogenic movements which raised the Carpathian mountains. The oil-field has been divided by the Roumanian Survey into two regions, the Flysch and the Sub-carpathian, as is shown in the accompanying sketch-map, Fig. 1. So far as is yet known, practically all the seepages and productive pits and wells are situated on anticlinals. Those which outcrop in the Flysch region (called Paleogene anticlinals), as indicated in the sketch-map, Fig. 1,are : Solontz,

Jan 1, 1907

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By Ronald W. Klusman, Erik B. Nelson

The Front Range portion of the Colorado Mineral Belt is an extensive area of mineralization with mining activity dating from 1859 with the discovery of large gold deposits. After an initial boom period and gradual diminishing production, present activity is restricted to molybdenum in Clear Creek County, uranium in Jefferson County, and several small operations extracting gold and silver in Clear Creek and Gilpin Counties. Gold and silver have dominated the production in the Front Range, though the complex mineralization created milling and smelting problems and it is postulated that considerable amounts of precious metals remain in the mine dumps. This area is plagued by a severe mine drainage problem, with Clear Creek most impacted by many draining mines and tailings in the basin. Boyles et al. Moran and Wentz, Wentz, Wildeman et al., have examined various aspects of the impact of mine drain¬age in the Clear Creek basin. The primary objective of this study was to collect data on the tailings, drainages, and leaching experiments in order to make preliminary suggestions for reducing the impact while recovering metal values to offset treatment costs. A variety of leaching experiments were performed on tailings from the Nevada Gulch area in the Central City mining district. Leachings were performed in vertical tubes indoors and wooden boxes exposed to the outside environment. In the leaching experiments, the leaching solution, grain size, and residence times were varied, while forced aeration was used in some experiments. Bacterial nutrient 9K° and mine drainage were used in some of the experiments. A total of 14 additional tailings samples were analyzed for base and precious metals. The composition of the mine drainage and tailings used in the leaching experiments, as well as data on the additional samples are shown in [Table 1]. Leachate samples were taken periodically for analysis until compositions leveled off. Results and Discussion Leaching with distilled water was used as a control and best illustrates the basic behavior of the leaching process for zinc in a vertical tube [(Fig. 1)]. More acidic leachings increased concentrations of metals as did smaller grain sizes, though the time required increased significantly. Mine drainage with its high concentration of dissolved iron sometimes decreased the heavy-metal concentration in the leachate due to oxidation of Fe 2 and precipitation of Fe(OH)9 which absorbs some of the dissolved heavy metals. In the larger scale experiment carried out in the simulated leaching pad, substantial concentrations of metals were attained in the final leachate after one month. In this experiment the leachate was not recycled, but allowed to saturate the tailings continually with evaporation loss made up by additions of Quartz Hill drainage and nutrient 9K. The concentration of the metals in the leachate and the increase over the input solution are given in [Table 2]. Heap leaching of low-grade copper and uranium ores is successfully carried out in many districts, enhanced by the metabolism of autotrophic bacteria of the Thiobacillus-Ferrobacillus group. These ubiquitous organisms enhance metal leaching, and general aspects of heap leaching are discussed by Malouf, Trudinger, Pings, and Duncan et al. Conclusions and Recommendations Returning to the primary objective, how to reduce the mine drainage impact and recover metal values, we need to consider how the data may suggest avenues toward this objective. Boyles, et al., considered various

Jan 1, 1977

By R. W. Vander Laan

Conneaut has a long and illustrious history as a major Great Lakes port for coal and iron ore. The first dock was built in 1892 for unloading iron ore from the Mesabi Range for shipment to the Pittsburgh steel mills via the Shenango & Lake Erie Railroad, later to become the Bessemer & Lake Erie Railroad. The Pittsburgh & Conneaut Dock Company was incorporated in 1893. The world's first Hulett automatic ore unloader was constructed at Conneaut in 1899. Steam operated, it was the model for the giant electric Huletts used today, named after its inventor, George Hulett, who was a Conneaut resident.

Jan 3, 1974

By Fred R. Harris

INTRODUCTION MacMillan Tungsten is located in northwestern Canada on the border of Yukon and Northwest Territories at a latitude of 63º17' and altitude of 1800 m above sea level. The deposit lies within the Selwyn Mountains 10 km from the Canol Road. It is 660 km by road from Whitehorse, Yukon, and 1325 km by air from Vancouver, British Columbia. MacMil lan Tungsten is a contact metasomatic deposit in gently dipping Lower Paleozoic limestone and limestone breccia adjacent to a Cretaceous quartz monzonite stock. Four tabular tungsten skarn horizons contain total geological reserves of 30 million tons grading 0.9% WO3. DISCOVERY AND HISTORY J.F. Allan, a former AMAX geologist, located mineral claims in September, 1962, to cover the source of scheelite-bearing skarn float found in the headwaters of Cirque Lake Valley. Exploration work on the property conducted mainly between 1968 and 1973, includes geological mapping, 10,500 m of diamond drilling in 73 holes, and 735 m of underground exploration. Mil 1 tests were carried out on a 300 ton bulk sample obtained underground. Preliminary feasibility studies, collection of weather data and a variety of environment studies have been carried out since 1973. Although no production date has been set MacMillan Tungsten will undoubtedly be a major tungsten producer.

Jan 1, 1976

By Alfonso W. Ovalle

INTRODUCTION The block-caving mining method is one of the most economical ways existing today to extract ore from nature. It is undoubtedly the least costly of the underground systems and moreover it compares favorably to open-pit mining. In addition to its low cost characteristic, the block-caving mining method permits a great extraction volume as can be exemplified by El Teniente's output capacity of over 22 million tons of ore per year. These characteristics of block-caving give assurance that, even though it is a very old mining system, it will be a good answer to the many future large massive low ore grade deposits to come and a1 so to rep1 ace open-pi t mining as such operations get deeper with higher stripping ratios. These are the reasons that induce further study of block-caving. In this paper block-caving at El Teniente is analyzed with due consideration to the major problems that this mine will encounter. Emphasis is given to the factors influencing the mining of soft ore which accounts for most of the ore to be extracted in the next ten years. A separate paper is devoted to a major modification introduced to block-caving hard primary ore at El Teniente by means of LHD equipment extraction. DESCRIPTION OF THE PRESENT MINING Ore Production and Flow Over 62.000 tons per day of ore are extracted 359 days per year at the El Teniente Mine. The Teniente 8 train haulage level at 1.983 m takes 29.000 tons daily to the Col6n Concentrator. Two trains make the 8 km haul with 16 cars per train. Car capacity is 90 tons. The Teniente 5 train haulage level 298 m above takes 33.000 t per day to the old Sewell Concentrator. Ore is produced from three production areas in two different levels. The so called North Mine produces 42.000 tons daily from the Teniente 4 level 65 m above the Teniente 5 haulage level. The Central Mine produces 1.000 tons from the first hard rock block caved at the Te- niente 4 level. The combined 43.000 tons per day production is sent through inclined 2 m dia- meter raises to the Teniente 5 haul age level , where 33.000 tons are taken 2.5 km to the Sewell Concentrator and 9.000 tons are hauled 0.5 km to a 5 m diameter vertical ore pass which sends ore to Teniente 8. The haulage is by 7 trains, 15 gabble-bottom cars per train. Car capacity is 20 tons. The so called South Mine produces 19.000 tons per day from the Teniente 1 level 645 m above the Teniente 8 haulage level. Ore is transferred by 2 m diameter inclined raises to the Ten 1 Retram level 22 m below, where 5 trains with 20 Sandfor Day cars per train, 8 tons capacity per car, haul the ore 1.5 km to two vertical 5 m diameter ore passes which connect to Ten 8. Starting in 1982 the Central Mine will in- crease production to 6.000 tons per day. An in- dependent loop haulage system will start operat- ing at the Teniente 5 level to feed a new under- ground 1.372 mm (54 in.) gyratory crusher which will send minus 152 mm ore (9 in.) to Teniente 8. In two or three years time the North Mine will only feed the 33.000 tons to the Sewel 1 Concentrator with its old Teniente 5 haulage system. The Col6n Concentrator will be fed from the Central and South Mines. Figure 1 shows the transfer systems and ore flows. The Ore Body In plan view at the Teniente 4 level the ore body has a kidney shape 1.800 m long and between 400 to 700 m wide. The north-eastern section of the ore body was washed away by the Teniente River. At the Sub 5 Level, 125 m below Teniente 4, the mineralization completely surrounds the circular 1.000 m diameter steep-sided barren breccia pipe (Braden pipe) . The ore body rock is 73% andesite, 14% diori te, 13% dacite and 6% mineralized breccia. Most of this ore is secondary enrichment sulfides which apart from the dacite is strongly fractured being chal cocite, cove1ine , bornite and

Jan 1, 1981

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By Paul E. Blackburn, Joan B. Berkowitz-Mattuck, Edward J. Felten

The oxidation behavior of MOSi2 has been studied between 450° and 650°C, the temperature region where "pesling" occurs. Disintegration ("pest-ing") of MoSi2 is shown to occur in the presence of oxygen, but not nitrogen, carbon dioxide, carbon monoxide. or argon. The rate of disintegration is extremely sensitive to oxygen pressure. The crack density of polycrystalline MoSi2 increases ivith lime at temperature. All kinds of cracks are observed: THE excellent oxidation resistance of MoSi, at temperatures of 1000 to 1700°C promises to have important technological benefits. However. the ap- Ihose which are confined within a single grain, those that ci'oss grain boundaries transversely, and those that follow grain boundaries. Laue photographs verify the existence of Iranscryslalline cleavage. Single crystals of MOSi2 do not "pest". Tlrcd solrlbility of oxygen in MoSi2 is extremely low, no lattice changes being observed as a result of exposure of MoSi2 to oxygen in the "pest" temperature range. plicability of MoSi2 is somewhat restricted by the occurrence of a completely destructive oxidation of the intermetallic phase at intermediate temperatures (300" to 6003C). This phenomena was ternled to be the "MoSi2 pest" by Fitzer who first observed it.' Molybdenum disilicide is a metallic material in both physical appearance and electrical properties.

Jan 1, 1965

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,' which had been used since the early 1930's by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell's plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell's practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami's reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."' A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. ' J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957

ATHOUGH the open-hearth charge contributes CO, CO2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion, the latter being regarded simply as the source of any extra heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were obtained by blowing in air or oxygen, as is the case in the Bessemer converter, then the net heat absorption would be negative, that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with Bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000°F. (1600 to 1650°C.) so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTTNG In the previous chapter it was pointed out that in a typical heat, the fuel furnishes about four million B.t.u. per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner (as is shown later), but it ranges downward from about one million B.t.u., depending not only on the charge but on the manner of calculation. In any event this requirement appears quite small in comparison with the heat furnished by the fuel and invites

Jan 1, 1944

For the year ending February, 1917 PRESIDENT L. D. RICKETTS,1 NEW YORK, N. Y. PAST PRESIDENTS BENJAMIN B. THAYER,1 NEW YORK, N. Y. WILLIAM L. SAUNDERS,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS 1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 3, 1916

By E. H. Crabtree, V. W. Winters, T. G. Chapman

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By E. H. Crabtree, T. G. Chapman, V. W. Winters

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

Detailed Geology of Certain Areas in the Mineral Hill and Warm Springs Mining District. By A. L. Anderson. T. H. Kilsgaard and V. C. Fryklund. Jr. Idaho Bureau of Mines and Geology. University of Idaho. 73 P. Maps, Illus.-Divided into three parts, this pamphlet covers the geology and ore deposits of the Hailey-Bellevue Mineral Belt, the Triumph-Parker mine mineral belt, and the ore deposits of the Mayflower Area. Numerous maps and illustrations are included for each area. Government Administration of the Copper Industry, World War 11. By John W. Douglas. 1950.51 P. $1.-This pamphlet covers in detail all the steps relating to control and operation of copper and copper products, and is of particular interest to primary producers, brass mills, wire mills, and foundries. Of particular current interest is the booklet's coverage of the steps leading to the Controlled Material Plan, into which industry is now once again heading. Copies can be obtained for $1 from John W. Douglas, Republic Foil & Metal Mills Inc., 55 Triangle St., Danbury, Conn.

Jan 12, 1951

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By H. L. Eiselstein, F. P. Huston, B. B. Betty

An extensive program for the establishment of creep data on high-nickel alloys has been in progress during the past seven years. This paper presents the accumulated data on two solid solution alloys, cold-drawn, annealed Monel and cold-drawn, annealed Inconel. Data on these two alloys in other conditions will be published at a later date. Monel, a nickel-copper alloy, is normally considered a corrosion-resistant material, but it will be shown that it also has considerable creep strength, validating its use at temperatures up to and including 900°F. Inconel, a nickel-chromium-iron alloy, is definitely a heat-resisting alloy possessing good creep strength and oxidation resistance up to iiooOF., and because of its oxidization resistance has been used successfully at much higher temperatures for lightly stressed parts. The literature contains but meager data on the creep properties of high-nickel alloys. Howevcr, Bennett and McAdam have presented a substantial quantity of creep data for cold-drawn Monel.1 The material as tested was not representative of mill production for it was cold-drawn to a reduction of area of 40 per cent as against 13 per cent, which is the mill standard for Monel. Twenty-two individual tests were run on each alloy in the investigation described in the following pages. The data and curves presented herein represent an integration of all the tests to obtain the most accurate picture of the creep properties of these alloys. Neither of the two alloys was found to be embrittled by the combination of temperature and stress, as evaluated by room-temperature tensile and impact tests that were made following creep testing. These data indicate that no tendency toward embrittlement exists. It is recommended that 6300 lb. per sq. in. be used as a working stress for cold-drawn, annealed Monel at 900°F. and 13,200 lb. per sq. in. for cold-drawn, annealed Inconel at the same temperature. Table 8 lists recommended working stresses, based on 80 per cent of the stress to produce a minimum creep rate of 0.01 per cent per 1000 hr., for Monel and some steels. Equipment The equipment used for these tests consists of Colville creep-testing machines manufactured by the Tinius Olsen Testing Machine Co. The load is adjusted, depending on the stress level, to give an error in the stress of not more than ± 0.1 per cent. This is based on considerations of lever sensitivity and the stress used for the standard (A.S.T.M. Tentative Standard E22-38T) 0.505-in. diameter creep specimen having a 2-in. gauge length. The single-specimen furnaces are provided with primary and secondary windings, from

Jan 1, 1945

The Committee on Nominations begs to submit the following names as its nominees for the respective offices indicated: For President, SIDNEY J. JENNINGS, New York. For Vice-Presidents, WALTER H. ALDRIDGE, New York; MARK L. REQUA, San Francisco. For Directors, J. E. JOHNSON, JR., New York; ALLEN H. ROGERS, Boston; HOWARD N. EAVENSON, West Virginia; ROBERT M. RAYMOND New York; WILLET G. MILLER, Canada.

Jan 12, 1916

By Harold V. Pearce

(Chattanooga Meeting, October, 1908.) THE fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant; and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the " Pearce " method for the separation of gold. At all events, it removes the business reasons which have prevented hitherto the publication of the principles involved. At the suggestion of Dr. Raymond, Secretary of the Institute, my father, Richard Pearce, the former manager of these works, has requested me to prepare a brief description of this process for the benefit of our members. Since I severed my connection with the Boston & Colorado Smelting Co. some time ago, I am indebted for some practical details to the present superintendent, Charles Rees, whose friendly assistance I would gratefully acknowledge. With regard to the history of the inception and development of this process by its inventor, Richard Pearce, I cannot do better than quote freely from his own notes and papers. HISTORY OF THE PEARCE PROCESS.' "In 1874 my entire time was directed to the improvements and additions to the plant at Black Hawk. The changes which I had made in the construction of the furnaces at Black Hawk proved so beneficial that I was requested to introduce the improvements at the branch works at Alma. These changes were carried out as speedily as possible, and proved of great advantage as compared with the old system. "The separation and refining of the gold from the matte now engaged my attention, and since previous experience in the treatment of gold-bearing matte and

Feb 1, 1909