Search Documents

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

By Peter Beardmore, Michael B. Bever

The effects of the temperature of deformation and the degvee of deformation on the annealing spectrum of a Au-Ag alloy have been determined by vesistance measurements. Specimens were deformed in torsion at 4°, 78K and room temperature up to strains nd/l of about 1.0 and were isochronally annealed. Discrete annealing stages similar to those found for pure metals were observed. Stage A occurred below room temperature; the decrease in reszstance associated with this stage increased as the temperature of deformation was lowered or the strain was increased. Stage B manifested itself as an increase in resistance; this is attributed to the restoration of short-range order promoted by vacancy or vacancy aggregate migration. At temperatures above 48S0K, recrystallization or Stage C occurred. Stages A, B, and C in the annealzng curves of this alloy may be considered to correspond to Stages II, Ill, and V, respectively, in the terminology used to describe the annealing spectrum of pure metals. ThE annealing behavior after deformation below room temperature has been thoroughly investigated on pure metals, in particular gold and copper. The occurrence of several discrete stages in the annealing spectrum of these metals has been established, but the interpretation of some of these stages in terms of specific mechanisms is still controversial.' The annealing of alloys deformed below room temperature has been the subject of only a few investigations. In the investigation reported here, a Au-Ag alloy was annealed after deformation at and below room temperature. This continues a research program on the deformation and annealing behavior of Au-Ag alloys.2-8s EXPERIMENTAL PROCEDURE An alloy rod of composition 82.6 wt pct Au-17.4 pct Ag was reduced to wire, 0.0428 in. diam, by swaging and drawing. After a recrystallization treatment, the grain size was 0.031 mm, as obtained from the average linear intercept.7 The ends of wires about 6 in. long were flattened and sealed into short brass tubes with cold setting cement to form the grips of the torsion specimens. The equipment used for deformation has been described elsewhere.6 The specimens were deformed at room temperature, 78", and 4°K to various strains nd/l, where n is the number of turns, d the diameter of the specimen, and 1 its length between grips. The strain rate ?max was 0.1 min-' at the sur- face of the specimen except where noted otherwise. The specimens were annealed isochronally for 30 min at intervals of approximately 30°K from the temperature of deformation to approximately 800°K, except that after deformation at 4°K the lowest annealing temperature was 78°K. A potentiometric method was used to measure the resistance: all measurements were made at 78°K with the exception of some measurements at 4°K mentioned below. Data obtained with a single specimen yielded a complete annealing curve: in several cases duplicate specimens were used to confirm the reproducibility of the curves. Since the surfaces of the specimens were rough after deformation, their diameters could not be measured accurately. The resistance increments after deformation and annealing are therefore reported as percentages of the resistance of the same specimen measured after completion of the annealing, that is, after full recrystallization. The corresponding resistivity values can be calculated by obtaining the effective diameter of a deformed specimen from the ratio of its resistance after recrystallization to the true resistivity, which was determined with a smooth specimen of known dimensions. This method of calculation was used to obtain data shown in several of the figures. RESULTS AND DISCUSSION The isochronal annealing curves after deformation to various strains at 4", 78K, and room temperature are shown in Figs. 1, 2, and 3, respectively. The resistance increment of the as-deformed specimens as a function of strain is shown in Fig. 4. For the specimens deformed at 4°K. values measured at 78°K are plotted with the exception of those for the as-deformed

Jan 1, 1970

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.'-' The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.' The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick's10

Jan 1, 1962

By P. W. Bridgman

Flow and fracture are admittedly complicated phenomena of which we are yet only partially masters. There is not even nni-.persal agreement as to the details of the language best adapted merely to describe the phenomena, to say nothing of any theory. Certain points of view, however, are widely held, and there are certain general expectations as to what sort of procedures will prove permissible. A complete description of any situation involving fracture would demand a complete history of all the variables in the control of the experimenter. The experimenter endeavors so to choose his independent variables that they are adequate to determine completely the situation in the sense that when an experiment is repeated on the same initial material and with the independent variables running through the same sequence, all the other measurable properties of the system will also run through the same course. It is, I think, the universal conviction that when we are dealing with phenomena of flow and fracture, the most important of the necessary variables are the external forces acting on the various parts of the body; when the force history repeats, with certain obvious restrictions such as that temperature must be constant and non-mechanical forces, such as magnetic field, must be small enough to be ineffective, then the history of all measurable properties will repeat; in particular the alteration of geometrical shape due to flow will run through the same course, and when fracture comes, the character of the fracture will be reproduced. Complete mastery of merely the descriptive aspects of flow and fracture would demand the ability to predict the entire course of flow and complete characterization of the final fracture for every possible combination of forces, varying in time in all possible ways, when applied to bodies of all possible shapes. This full situation is obviously of prohibitive complexity. The first stage in reduction to manageable simplicity is to resolve the total situation into the sum of contributions made by small elements. Our thesis is that if each of the elements is adequately characterized, the behavior of the whole system is fixed. The element is usually taken of a simple geometrical shape, suggested by the mathematics best adapted to the particular situation. The forces acting across the faces of the elements are ultimately determined by the forces acting across the free faces of the whole system. The detailed process of finding the precise forces on the faces of all the elements in terms of the external forces involves the use of a special mathematical invention, the stress, a constructional quantity consisting of six components. The stress at any point in the body is determined by both the external force system and by the physical properties of the body at all points; quite different stresses prevail at the interior of bodies of the same shape under the same external forces in the elastic and plastic ranges. The forces on the faces of any element are, however, uniquely determined by the stress system at the element. Our fundamental thesis

Jan 1, 1945

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

Although the meeting of the Institute in St. Louis Will not occur until September, 1917, the committee in charge is already making attractive plans, and we append hereto a tentative skeleton program which will give some notion of the opportunities that will be offered: St. Louis is situated in the midst of. a district which contains not only a great many interesting examples of mining, but also all types of industrial manufacture of interest to members of the Institute, and it affords abundant opportunities to visit and see these plants. Further announcement will be made from time to time as the committee's plans take more permanent shape. .

Jan 2, 1917

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

By Graham Bright

Before the arrival of central-station power, all coal and metal mines generated their own power and, in many cases, these isolated power plants gave a fair continuity of service. In coal mines that produce considerable gas, it is essential that power be available at all times for operating the ventilating fan and the hoist, if the mine is of the shaft type. In the case of an isolated power plant, if trouble should develop with the fan the men can be hoisted quickly when the mine is of the shaft type. On the other hand, if trouble develops with the hoist, the fan can be kept in operation, and there will be no necessity of haste in getting the men from the mine. Now that central-station power is being used so extensively for mine service, the continuity of service with gaseous mines is very important. : Inherently, the central station is much more reliable than any isolated plant, but trouble may occur on the transmission lines which may prevent the transmission of power for a considerable time. : Some mines have kept their steam equipment intact and ready for operation in case the purchased power should fail. This is expensive procedure, for the boiler plant must be fired at all times so that the emergency power will be quickly available. In a number of instances, gasoline-engine driven generators have been installed to furnish emergency power for the service hoist. As most service hoists are of the alternating-current type, the generator of the gasoline-engine driven set is usually of the a.c. type and is arranged to drive the service hoist motor at full speed, or an extra motor that can be thrown into gear on either the main or service hoist and the hoist operated at a greatly reduced speed. This arrangement is used because it is difficult and expensive to obtain and install large gasoline-engine driven units. The author has recently developed a plan by which the main hoist and the fan can both be operated at reduced speeds, in case of loss of power from a central-station power system. In this plan a gasoline-engine

Jan 1, 1923

Flaubert, as we know, laid stress on the selection of the right word, le mot juste, the precise epithet, the word that belongs to the thing. A sentence, or even a paragraph, may be spoiled. by the use of a word that is not proper, that does not fit or is foreign to the meaning intended. An Australian mining expert is reported to have said: You have a property of considerable value, and what I saw warrants s good development of very rich cubicular galena, with gossan intermixed. 'Cubicular' means 'belonging to a small bedroom', a 'cubicle' being a sleeping compartment. He meant 'cubic', of course. This is a malapropism, and reminds me of the lady from Chicago that, on her return from Europe, said how much she had enjoyed the rural parts of France, because, among other things, it was "so delightful to hear the French pheasants singing the mayonnaise to the tune of the Los Angelus". It is impossible to amalgamate coal-tar thoroughly with the pulp in the agitating-tank. In metallurgy, 'amalgamate' refers to the combination of mercury with one or both of the precious metals, forming an amalgam, which is an alloy of mercury with another metal. It differs from other alloys, such as brass or bronze, in being made without the aid of heat, inasmuch as mercury is molten at the ordinary temperature. The word comes to us from the Greek through Old French and means 'something soft'. It is a mistake to use technical terms, having a specific meaning, for purposes that are foreign to that meaning. The writer of the quotation is not discussing any combination of metals; he is dealing with the physical process of mixing and is using 'amal-

Jan 1, 1931

By G. E. McElroy

MUCH attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for equal values of the product W D V, where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and m = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Prof. Osborne Reynolds' more than 40 years ago. Later, Lord Rayleigh amplified the theory2 which has been conclusively proved for small pipes by the experiments of Stanton and Pannel3 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,5 has outlined the application of this theory to mine-air flow and recent English experiments' on the resistance of a timbered mine airway have been expressed in this form.

Jan 10, 1926

By G. Willard Quick

TENSILE tests of rail steels at elevated temperatures'' have shown that certain rails, in addition to having low ductility in the well-known bluebrittle range in the neighborhood of 200° C., have marked reduction in elongation and reduction of area in the temperature range from 400° to 700° C. This range of low ductility was called "the secondary brittle range" and the phenomenon, "secondary brittleness." The question naturally arises as to whether this property of the steels would be shown by impact tests performed in the same range of temperature. If so, the impact test, as suggested by Gillett3 would be a simpler and quicker method for the routine examination of steels at elevated temperature than the tensile test. A number of investigators have reported results of impact tests on steels at elevated temperatures, in which the energy absorbed decreased with increase of temperature above 200° or 300° C. Langenberg4 performed Charpy impact tests on several steels at temperatures ranging from room temperature up to 1000° F. (538° C). His results showed an increase in the energy absorbed in specimens tested in the range from room temperature to 200° or 300° C. and then a gradual decrease in the range, 300° to 538° C., the maximum temperature used. Greaves and Jones5

Jan 1, 1932

By William Romanoff

IN AN ARTICLE on "Recovering Smelter Dust and Oxide," published in the Engineering and Mining Journal (Vol. 131, No. 2), the authors briefly described some dust-recovery equipment and its operation at a secondary-metals brass-smelting and refining plant. A description of our experience in overcoming certain operating difficulties may prove of interest or value to those who are confronted with some of the same problems or who should equip their furnaces with dust-collecting equipment. The dust loss from reverberatory smelting and refining of brass con¬sists largely of zinc, with smaller percentages of lead, tin, and copper in the order named. At the Kramer plant, the fume discharge from the two stacks amounted to 3 to 4 tons of solids per day, making a dense smoke. With dust equipment in operation, the discharge from the stacks is invisible and approximately 2500 lb. of zinc and other metals is recovered daily thereby from each furnace operating.

Jan 1, 1933

By G. R. Lehman

The Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the "shrinkage-stope" or "caving" methods a lower extraction of the developed ore, at a lower mining cost. Ore-Drawing Tests To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or " caving " methods. As no definite information regarding the,question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore. The Experimental Box The experimental box shown in Fig. 1 was made of wood and glass. The glass was used for the sides so that the drawing action of the outside row of chutes could be seen and noted, the latter being cut in the center by the glass sides. The length of the box was 30 in., width 20 in. and the

Jan 1, 1917

By Walter W. Bradley

Mining by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being discharged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,' in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Commission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however, through what is known as the Trinity and Klamath River Fish and Game District. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1937

By John M. Cummings, Warren. Harry V.

THE Geology Department of the University of British Columbia has undertaken the task of examining the ores from as many as possible of the gold mines of British Columbia. The object of this work is two- fold. First, it is known that detailed mineralographic studies are useful in attacking ore-dressing problems, and these studies are intended to be helpful to mill operators. Second, it is hoped that mineralogical and mineralographical studies will prove useful adjuncts to those of lithology and structure in throwing more light on problems related to the origin of the deposits. The paper shows that gold, for all practical purposes, is not present in an ore mineral in solid solution nor as a eutectic with any mineral; if the latter were true the gold particles would be distributed equally throughout that mineral. The gold occurs either as native gold or as a gold-silver telluride and is not distributed regularly through any mineral or minerals. The relationship between the gold or gold-bearing telluride and the associated minerals affords a means of classification that is not only simple but also appears to be directly related to the geological nature of the deposit, which may be summarized as follows: 1. Disseminated Gold Type.-Precious minerals in extremely small grains, which are distributed without regard to grain size, fractures or grain boundaries: (1) Hedley variety-gold in native form; (2) Surf Point variety-gold predominantly as telluride. 2. Veining Gold Type.-Precious minerals in grains of various sizes, which occur mainly along fractures and grain boundaries: (1) Cariboo gold quartz-goldin native form. (2) Waneta variety-gold as telluride. Application Te Ore Dressing These mineralographic studies have proved to be of value to mill operators, and future studies of a similar nature should prove increasingly useful because every year provides a further opportunity to correlate

Jan 1, 1937

By D. Harper

The National Pocahontas Mine in Wyoming County, WV, has been developed in the Pocahontas No. 3 coal. During 14 months of ventilation surveys, the locations of large rockfalls, many in areas infrequently visited by mine personnel, were mapped. Several dozen rockfalls were later studied in detail. Kettlebottoms, rider seams, root-penetrated roof strata, slicken sides, and shales that spall are common in areas with a high density of rockfalls. Large-scale crossbedding and micaceous and carbonaceous films in sandstones are less common. Density of rockfalls in any area is related to the time elapsed since mining, thickness of overburden, and orientation of entries and panels. Some linear features overlie areas where rockfalls are densest. Most rockfalls occur during summer.

Jan 1, 1983

By Wallace Ralston

The East Texas area includes the northeast 38 counties of the state of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It is one of the most important oil and gas-producing areas of the Mid-Continent Province. It includes four important oil fields—Van, East Texas, Cayuga and Long Lake— and the recent extension of Rodessa field into Cass County, Texas, may prove to be of major size. Four commercial gas fields are in this area— Bethany, Waskom, Cayuga and Long Lake. Up to January, 1936, all of the oil has been produced from the Upper Cretaceous formations, and most of that from the basal member, the Woodbine sand. Gas is produced from both the Upper and Lower Cretaceous formations. Development in Fields East Texas Field.—This field continued to dominate the drilling and production situation throughout the United States. There were 4036 wells completed in this field during 1935; that is, 365 more wells than were completed during 1934. Drilling activity was due to close spacing of wells and the addition of 10,000 acres to the field. The field is now drilled to a density of one well to 6½ acres, which is certainly more wells than necessary for economic production of the field. The close spacing of wells is due mostly to the type of proration, which is per well allowable based on a potential test, and does not take acreage into consideration, and also to the numerous small acreage tracts such as town lots and excess strips. The field now has 19,519 producing wells. The allowable production for the field during 1935 was 161,118,659 bbl.; estimated production, including illegal or "hot oil," was 174,200,150. The illegal production of oil gradually decreased throughout the year, until an estimated low was reached of 20,500 bbl. daily during the months of November and December. The price of oil remained at $1.00 per barrel throughout the year. As stated, about 10,000 acres were added to the field during the year, making a total of 128,000 productive acres. There is a possibility that

Jan 1, 1936

By D. Kramer

HASEN1 has published a phase diagram for the zirconium-nickel system. This phase diagram has been redetermined by Hayes, Roberson, and paasche2 in the range 0 to 50 at. pct Ni. Recently, Smith and Guard3 have published a tentative diagram for the

Jan 1, 1960

By H. K. Birnbaum, H. B. Aaron

he authors suggest that a number of the types of yield phenomena which have been observed in high-purity fcc metals are due to dislocation interactions bccurring at the surface of the crystals rather than due to volume effects. Since rather different inter-pretationS2,7,12,14,15,21-23 of these effects have been suggested, it is of some importance to ascertain the role of the surface in these yield phenomena. It should be first noted that the high-purity fcc metals appear to exhibit several distinct types of yield phenomena. The "unloading yield point" which is observed on reloading the specimen after removing the applied load has been found to be independent of the time of holding in the unloaded condition. If however the specimen is aged while under load and re-tested without removing the load, a yield point is observed which does depend on the aging time and tem-perature. Feng and Kramer suggest that the removal of the unloading yield point on removing sufficient material from the surface of the specimen indicates that the effect is associated with dislocation interactions at the specimen surface. Their observations are counter to those of Haasen and Kelly5 and Birnbaum.12 Since the unloading yield points are extremely small (-2 pct of the flow stress) the results of the surface removal will depend on whether the material is removed uniformly over the gage length. The introduction of small etch pits or the removal of more material from one portion of the specimen than from another will result in preferential yielding and obliteration of the yield point. With the normal electropolishing techniques it would be difficult to avoid these effects. The data obtained by Aaron and Birnbaum, Fig. 10, on aluminum polycrystalline specimens indicate that, although the unloading yield point and the strain-aging yield point are not simply additive, a time- and temperature-dependent yield point is observed under conditions where no creep is observed. This does not agree with the results of Feng and Kramer but does agree with the results on copper15 and gold.7~23 The source of the discrepancy may be the procedure used by Feng and Kramer to correct their time-dependent yield points for the effect of creep. Since the strain-aging yield point is not independent of the pre-aging strain rate, Fig. 11, the effects of creep cannot

Jan 1, 1967

By Alan Morris

BRASS rod for use in automatic screw machines is one of the major products of the brass mills. A large tonnage is consumed each year in the manufacture of an endless variety of finished articles and parts for assembly into other products. The machines that do this work have been developed to a high degree of efficiency, and their manufacturers are still striving for higher production speeds. This development has brought with it a demand for brass rod to meet the increasingly difficult machining conditions. This paper is a report of the results of tests undertaken in an effort to obtain a measure of the effects of such variables as lead content, microstructure and cold work on the machinability of brass rod. It is realized that the term "machinability" has never been well defined. Power, finish and tool life all should have a place in such a. definition. In practice it is sometimes found necessary to sacrifice some of these in order to obtain a rod that will not tend to throw up a burr, or will give a burr which is easily tumbled off. Again a specially stiff rod may be necessary because of long overhang from the chuck or a rod of special characteristics is needed to take a given broaching operation without chattering. It is only through an understanding of the effect of basic mill operations on the machinability of the rod that such problems as these may be solved most economically. It is hoped that this paper, together with the discussion it may evoke, will prove to be a basis for such an understanding.

Jan 1, 1932