Search Documents

By Ian M. Thomson, Robert W. Greene

Last August, American Commercial Barge Line Co. (ACBL) began moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tenn. By April of 1973, this movement will reach a level of 7 million tpy. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million and is now in possession of reserves containing about 120 million tons of recoverable No. 9 coal, and about the same recoverable amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Co. to mine the No. 9 seam through two slope shafts. The mines are about 300-ft deep and are separated by the one major fault on this property. The mine portals are approximately 3 ½ mi apart, with the northern portal being over nine miles distant from the Ohio River.

Jan 1, 1971

By H. P. Greenwald

THE rapidly increasing use in coal mines of portable auxiliary fans, which are generally "blowers" employed in connection with canvas tubing, raises questions concerning the hazards of such equipment, especially where the practices are opposed to established methods of ventilating face workings. Half a dozen or more coal-mine explosions and some fires have been attributed to the use of auxiliary fans; moreover, competent mining engineers have found many dangerous installations and methods of use-for example, intermittent running of the fans in gassy mines with consequent accumulations of firedamp at the faces. These facts have led the U. S. Bureau of Mines to issue this recommendation: "In the interest of safety, the Bureau of Mines, Department of Commerce, recommends that auxiliary fans or blowers should not be used in coal mines as a substitute for methods of regular and continuous coursing of the air to every face in the mine." The comparatively recent introduction of new types of mining machines, mechanical loaders, face conveyors, and slabbing machines has encouraged the trial of new systems of face mining, all of which have for their object the rapid advance of the faces. Although the latter has certain economic advantages, in gassy mines the rate at which gas is given off is generally found to increase in proportion to the speed of advance into new territory, which in turn increases the difficulties of efficient ventilation of the face workings. Some of the systems of advance mining being tried in connection with new mechanizing methods practically compel the use of blower fans and tubing, as single narrow places are now driven, 300 ft. or more without crosscuts. In some instances a series of parallel headings are driven without crosscuts pre-

Jan 1, 1928

By H. P. Greenwald, H. C. Howarth

The rapidly increasing use in coal mines of portable auxiliary fans, which are generally 'blowers" employed in connection with canvas tubing, raises questions concerning the hazards of such equipment, especially where the practices are opposed to established methods of ventilating face workings. Half a dozen or more coal-mine explosions and some fires have been attributed to the use of auxiliary fans; moreover, competent mining engineers have found many dangerous installations and methods of use-for example, intermittent running of the fans in gassy mines with consequent accumulations of firedamp at the faces. These facts have led the U. S. Bureau of Mines to issue this recommendation: "In the interest of safety, the Bureau of Mines, Department of Commerce, recommends that auxiliary fans or blowers should not be used in coal mines as a substitute for methods of regular and continuous coursing of the air to every face in the mine." The comparatively recent introduction of new types of mining machines, mechanical loaders, face conveyors, and slabbing machines has encouraged the trial of new systems of face mining, all of which have for their object the rapid advance of the faces. Although the latter has certain economic advantages, in gassy mines the rate at which gas is given off is generally found to increase in proportion to the speed of advance into new territory, which in turn increases the difficulties of efficient ventilation of the face workings. Some of the systems of advance mining being tried in connection with new mechanizing methods practically compel the use of blower fans and tubing, as single narrow places arc now driven 300 ft. or more without crosscuts. In some instances a series of parallel headings are driven without crosscuts pre-

Jan 1, 1928

By Oswald J. Heinrich

(Read at the Philadelphia Meeting, February, 1878.) DURING the last twenty years much has been done to investigate and define the Mesozoic formation of the United States along the Atlantic States, as well as in the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geological surveys of Penn-

Jan 1, 1878

By George H. Jones

NO STRANGER phenomenon exists in the American mining industry today than the so-called bootleg anthracite industry in Pennsylvania which now produces probably close to 15 per cent of the total hard coal out- put of the State. Instead of being what - was first thought to be a temporary condition, countenanced because of the desperate condition of some of the miners at the depth of the depression. it is thriving now as never before. Re- ports of it have penetrated all over the world, as exemplified by inquiries concerning it in Durban, South Africa mentioned by John C. Cosgrove in his article in the July MINING AND META LURGY.

Jan 1, 1939

By Theo B. Comstock

TO the large majority of visitors the unique features of the National Park are interesting chiefly on account of their novelty. Scientists of all schools may find here food for reflection, and much that is rare and marvelous; but the real, practical uses of the reservation, aside from its pleasure-giving adaptations, are not as yet fully appreciated. Since 1873, the writer has on frequent occasions expressed freely his own views upon the proper means of utilizing the Park for the best interests of science.* Some of the recommendations made have been adopted by the authorities. At the suggestion of friends I present here a brief statement of facts concerning matters which may be of advantage for visiting engineers to know, hoping that the very limited stay of the Institute may thereby be rendered a little more profitable, and that our common profession may possibly receive some benefit. First, then, it should be understood that, as in many other cases in. the West, the present routes to the Park from the south are not the most direct. The expedition of Captain (now Major) Jones in 1873 discovered a practicable route for a, wagon or railroad via the head of Wind River, through To-gwo-tee Pass and Two-Ocean Pass, by which the distance from Point of Rocks, Wyoming, on the Union Pacific R.R., to the Yellowstone Lake, is only 290 miles. Eventually, it is probable that a railway line from Cheyenne or some other point in Wyoming will be constructed, which, taking advantage of

Jan 1, 1888

By D. H. Newland

During the year 1907 an investigation of the Clinton formation in New York has been carried out under the direction of the State Geologist, and a full account of the results has been prepared for publication.' The more important economic features of the report are summarized in the present paper. Previous knowledge of this, the type, section of the Clinton has been contributed mostly by Hall and Vanuxem in their reports for the Natural History Survey of New York, which were issued in their final form in 1842-43. Brief accounts of the ore-occurrences have been given by 13. T. Putnam? J. C. Smock: A. H. Chester: and E. C. Eckel.5 Prof. C. H. Smyth, Jr.,6 has discussed the origin of the Clinton ores in two papers, which, so far as the local occurrences are concerned, have removed all doubt that may have existed on that subject. Distribution of the Clinton Formation. The Clinton strata in New York State are restricted to a single belt, which extends from the eastern central part to the Niagara river, which it crosses, and thence continues for some distance into the province of Ontario. The New York

Jan 1, 1910

By Leonard Grimshaw

DIFFUSION Of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been consider-able, and includes many reports in foreign languages. This work has recently been well reviewed by Mehl1 and Krynitsky,2 and the reader is referred to their excellent bibliographies.

Jan 1, 1937

By John L. Schroder, D. L. McElroy

ALTHOUGH the earliest use of rubber-tired haulage was in Illinois in 1936, the first unit of this type of equipment used in West Virginia was shipped into the state in 1938. All units placed in West Virginia mines have been of the shuttle-car type. The Katherine Coal Mining Co., at Lumberport, W. Va., was the second company in the United States to install shuttle cars and the Gay Coal and' Coke Co., at [ ] Mt. Gay, W. Va., was the first company in the country to install the thin-bed type of shuttle car. On Oct. 8, 1940, nine companies in the state were using 41 shuttle cars, of which 10 cars at three mines were of the thin-bed type. All shuttle cars of the low type were in the southern fields and all of the high type were in northern West Virginia. At that time several units were in the process of delivery. The data in this paper were collected in the field by Mr. Schroder in connection with graduate work on mechanical loading of coal in West Virginia by mobile loaders. In the course of his field work he visited five mines in the state that were using shuttle cars. All of these mines were in high-volatile coal beds of strong structure. [ ] The more pertinent data obtained at the mines visited are given in Table I. The maximum distance of shuttle-car haul is the distance between the transfer station and the farthermost place. Tonnage per loading unit per foot of bed thickness is to some degree a measure of relative efficiency, especially if the different operations are working the same bed or have somewhat similar conditions. The thin-bed operation is well up in the higher bracket of the afore-mentioned column, which is as

Jan 1, 1941

By R. F. Mehl

Jan 1, 1936

Jan 1, 1922

By A. E. J. Engel

INDUSTRIAL talcs and ground soapstones both include earth materials of different chemical and mineral compositions. In general, the industrial talcs are composed of silicates that contain appreciable amounts of magnesia. Generally talc, the mineral, is a predominant or at least common constituent. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3 (SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.11 Actually different single grains or leaves of pure talc have variations in water content ranging from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.16 Only a very small percentage of the ground industrial talcs produced in the United States approaches the composition given above (see Table 1). The purer talcs invariably occur as alteration products of magnesium carbonate rocks. Some of these relatively pure talcs include compact, massive types largely mined in California, which are designated as steatite.38,58 In general, steatites cannot contain in excess of 1.5 pct CaO, 1.5 pct combined FeO and Fe203, and 4 pct A1203. The less pure varieties of massive talc and mixtures of magnesian silicates are commonly called soapstones, or merely talc. Many industrial earth products classified as talc or as soapstone contain a variety of minerals, especially serpentine (H4Mg,Si2O9), chlorites (hydrous magnesium, iron, aluminum silicates), tremolite (Ca2Mg5H2[SiO3]8), anthophyllite ([MgCa]SiO3), diopside (CaMg[SiO3]2), and quartz (SiO2). The carbonates calcite (CaC03), dolomite (CaMg[CO3]2), and magnesite (MgCO3) are also present in some industrial talcs and soapstones. Some of these minerals, as well as sulphides, sulphates, and iron and manganese oxides, if present at all or in excess of minute amounts, may alter the composition of the industrial talc sufficiently to restrict materially its use or to lower or destroy its value. These factors are discussed in a subsequent section of this chapter.

Jan 1, 1949

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

By R. A. Vandermeer

It is usually assumed that the rate-determining step in the migration of a grain boundary involves the thermally activated transfer of single atoms across the interface. Chemical reaction rate theory then gives a migration rate which is proportional to the driving force when this is small compared to kT.1 In their recrystallization studies on aluminum, Gordon and vandermeer2 obtained data which was capable of providing the first experimental test of this proportionality. They correlated stored energy (driving force) release measurements determined calorimetrically with fraction recrystal-lized kinetic (growth rate) data acquired metallo-graphically at a temperature where a significant amount of recovery takes place concurrently with recrystallization. Within experimental error, the results of Gordon and Vandermeer confirmed experimentally, at least over a limited range, the linear dependence of boundary migration (growth) rate on driving force in accordance with theory. In obtaining these results, however, an incorrect, implicit assumption was made in relating the average instantaneous growth rate of the recrystallized grains to the measured fraction recrystallized kinetic data. The purpose of this present note is to point out and correct this assumption. An alternate approach, whereby a more proper average growth rate can be calculated from the recrystallization kinetic data, is presented. The earlier data, reevaluated in terms of this new approach, show the same general trend as before so that the original conclusion of Gordon and vandermeer2 is still valid. As was shown in a detailed study3 of the geometrical features of recrystallization in aluminum, the colonies of recrystallized grains can be regarded as uniform cylinders embedded in a three-dimensional matrix, the number of such colonies being constant. Thus during the early stages of recrystallization the volume fraction recrystallized, Xv, can be written as Xv=ynvlr2 [l] where y is a shape factor and i and r are defined as the average length and radius of a recrystallized colony and are spatial averages over the specimen. -nv, is the number of such colonies in a unit of volume. The erroneous assumption made in the earlier paper2 was that r in Eq. [I] could be replaced by

Jan 1, 1965

By J. Spotts McDowell

INTRODUCTION The magnitude of the thermal expansion of silica brick, and its inability to withstand rapid temperature changes, present problems of considerable importance in the manufacture of siliceous refractories. In the study represented by the experimental data herein described, these problems are considered from the point of view afforded by the results of recent investigators: Fenner and his associates of the "Geophysical Laboratory, Washington, D. C., who have established the stability relations of the silica minerals, and Endell and co-workers in Berlin, who have studied the changes brought about in the constitution of siliceous refractory materials upon the application of heat. In the process of manufacture, the quartzite from which the brick is made changes in part into cristobalite and tridymite. The attempt is herein made to determine by microscopic methods the degree of transformation in various specimens of test bricks manufactured at slightly varying temperatures of burning, with varying coarseness of grain, and to determine the effect of repeated burning. The effect of variations

Jan 10, 1916

By C. W. Pritchett

Several years ago, during a trip from Jojutla to Huauatla, in the abate of Morelos, Mexico, I was told by my guide of the ruins of an old smelter near by, and my curiosity was excited to such an extent that I went out of my way several miles to see them. I found them very interesting; and, as I fortunately

Jan 1, 1902

[ ]

Jan 1, 1938

Jan 1, 1969

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By O. D. Sherby, J. E. Dorn

For elevated temperature-constant load creep tests of a solid solution alloys, the creep strain is a function of a temperature-compensated time parameter 0 = je H/RT dt. The activation energy H is equal to o constant of about 36,000 cal per mol. The substructures resulting from a given creep stress condition are functions of the creep strain independent of temperature. Each new creep stress gives a new unique set of grain substructures; this is one of the factors responsible for the failure of the mechanical equation of state for creep. IN this report an attempt is made to correlate the creep properties of dilute a: solid solutions in aluminum with the subgrain structures that are developed during creep. The possibilities of such correlations have already been suggested by Wood et al. and others1-" who demonstrated that the subgrain structures are functions of the creep stress, creep strain, rate of creep, and temperature. Investigations by Sherby and Dorn' have shown that the creep strain, E, at constant load for dilute a solid solutions of aluminum is given by the functional relationship: e = f(8,u,) [1] where: 0 equals te-AH/RT = temperature-compensated time; t, time; AH, activation energy, - 35,800 cal per mol; R, gas constant; T, absolute temperature, above 400°K; and u,, initial creep stress. Consequently, it was anticipated that the subgrain structure that develops during a constant load creep test should also correlate with any two of the three significant variables C, 8, and Another possible correlation between the subgrain structure and the creep variables is obtained by differentiating Eq. 1 with respect to time, whence the creep rate, 2, becomes: = (2L) (2) =f (, u,) e-AHRT [2] or: e = F (c e H/RT, 0) [3] For the minimum creep rate, ;,, 8 is solely a function of U, as revealed by Eq. 1. Consequently, at the minimum creep rate Eq. 3 reduces to: = F (eAH/RT) [41 Correlations between U, and i, eAH/RT were found valid for solid solution alloys of aluminum where AH was a constant of about 35,800 cal per mol. The parameter ;, eH/RT is identical to the Zener-Hollo-mon parameter8," used by them in evaluating the tensile properties of copper and other metals. Eq. 4 suggests that the subgrain structure developed during secondary creep might be correlatable with either of the two variables 2, e H/RT or u,. Some of the solid solution aluminum alloys which were discussed in an earlier report' were also used in the present investigation. Sheets of these alloys were homogenized, cold rolled from 0.100 to 0.070 in. in thickness and then recrystallized to about the same grain size. Their chemical composition and grain size are recorded in Table I. Creep specimens were selected with their tensile axes in the rolling direction. The details for creep testing have been described10 and will not be repeated here. All creep tests were performed under constant load conditions. Experimental Results and Discussion Metallographic Structure of Creep Specimens: In order to obtain a preliminary concept of creep on the metallographic structure of high purity aluminum, the various ruptured specimens previously used to obtain the creep data for pure aluminum were polished and etched electrolytically in a dilute solution of fluoroboric acid. Oblique illumination was used to reveal the substructures which, for convenience, are shown in correlation with the vs. ;, eH/RT curve in Fig. 1. It is necessary to emphasize that the data for the curve refer to the various secondary stages of creep whereas the micrographs refer to the fractured creep specimens. Nevertheless a regular and systematic correlation is observed between E, eAH/RT (or the creep stress) and the micro-structure at fracture. For In (e, eAH/RT) = 42.3, which refers to creep at a high creep rate and a low creep temperature, the fractured aluminum specimen, as shown by the micrograph in the upper right-hand corner of Fig. 1, exhibited extensive deforma-

Jan 1, 1954