Search Documents

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country's production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber's salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

A. L. FIELD, Cleveland, Ohio (written discussion*.-)In equation 2, B is used to denote the ratio of bases (lime plus magnesia ) to acids (alumina plus silica) it being stated that this ratio gives more concordant results than the ratio either of bases to silica, or of lime to silica. I find, however, that, by making use of the ratio between true CaO (CaO by analysis minus sulfur calculated to CaS) to acids, equation 2 may he modified to agree with the observed facts within an average error of 0.0041 per cent. sulfur instead of 0.0045 per cent. The revised equation is s = 0.072 + 0.01835 - 0.00061 (t - 1400) - 0.0403B where B is the ratio of true CaO to Al2O3 Plus Si02, and the other symbols have the same significance as before. I would not appear to stress too much this slightly better agreement of the revised equation with the observed sulfur. Yet I believe that the use of this ratio of true CaO to acids is to be preferred, if for no other reason than the fact that it is more in harmony with the previous findings of the Bureau of Mines with regard to the effect of magnesia and other impurities on slag viscosity.1

Jan 12, 1919

Jan 1, 1941

By J. Brett, L. Seigle, L. Castleman, T. Montelbano

Impurity-induced low-temperature recrystallization of cold-worked tungsten was inuestigated with emphasis on the influence of nickel on the reaction. Palladium, nickel, aluminum, manganese, platinum, and iron greatly lower the recrystallization temperature of doped tungsten, which zs normally very high, but the recrystallization temperature of electron-be am zone-refined tungsten wzre is slightly raised by conlacl with nickel. Recrystallization can be induced at low temperature by the presence of solid nickel on the surface of doped tungsten wire, but apparently not by exposure to nickel vapors alone. Approximately 200 ppm of Ni dijjused into 10-mil wires at 1200 from a deposit of nickel on the surface produced total recrystallization, whereas more than 600 ppm of Ni could be absorbed frotn a vapor source without altering the fibrous structure of cold-worked tungsten. Once initiated, nickel-induced recrystallization required a continued source of' nickel for propagation of the recrystallization front. The solubility of nickel in fibrous 10-mil W wire was approximalely 500 ppm at 1150' C, and the activation energy for penetration of the recrystallization front was 52 kcal per mole. In many applications the usefulness of tungsten depends on critical control of its structure. Cold-worked tungsten with the fibrous structure developed by suitable thermo-mechanical treatment has a low, but technologically significant, ductility. It has long been known1 that traces of nickel, and perhaps other metals, are profoundly deleterious in doped tungsten, because they induce recrystallization at low temperature, which produces a brittle, equiaxed grain structure. This effect appears to be an exception to the general observation that recrystallization is impeded and the recrystallization temperature raised by the presence of impurities.2"9 Previous studies7-'' of the annealing and recrystallization of tungsten wire have divided the phenomenon into prior recovery stages, primary recrystallization and secondary recrystallization. The present investigation is concerned principally with primary recrystallization which is defined here as the replacement of the fibrous structure of deformed tungsten by equiaxed grains. The objective of this study was to explore the nickel-induced recrystallization reaction in tungsten and attempt to elucidate its mechanism. As well, an effort to define which other elements give rise to low-temperature-induced recrystallization was carried out. EXPERIMENTAL PROCEDURE The procedure adopted for these experiments was essentially to bring nickel and other elements into diffusive contact with cold-worked tungsten wires. The process of recrystallization was followed as a function of time and temperature by light and electron microscopic observations. First the influence of nickel on the recrystallization temperature of arc-melted, zone-refined, and variously doped tungsten wire was determined by electroplating a deposit of nickel on the surface of the wire and annealing at a variety of temperatures for 3 hr. The chemical analyses of the tungsten wires used in this investigation are given in Table I. The surface of the tungsten wire was etched with Murakami's slution' and approximately 0.005 in, of Ni was deposited from a Watts-type low pH bath14 for the conditions of these experiments. Variations in plating thickness from about 0.001 to 0.005 in. had no discernible influence on the resulting structures. The wires were then annealed in an atmosphere of dry hydrogen to establish the recrystallization temperature. Concurrently, un-plated specimens were annealed to establish the recrystallization characteristics of nickel-free wire. The criterion of recrystallization was that the fibrous structure be completely replaced by equiaxed grains after a 3-hr treatment of temperature. This provided more reproducible results than use of the first recrystallized grain or a fixed proportion of re-crystallized structure as the critical observation. The structures encountered in longitudinal and transverse sections were examined by both light and electron microscopy at magnifications up to X32,000 using parlo-dion-carbon replicas shadowed with platinum for the latter method. Second, the influence of a variety of metals on the recrystallization temperature of 0.010 in. D alumina-silica doped tungsten wire, AW136-64, was determined. The elements were applied by electroplating whenever possible. Alternatively, they were vapor-plated on the tungsten wire and a greater thickness built up by coating with a dispersion of metal powder in nitrocellulose lacquer. Elements not amenable to either of these procedures were merely slurry coated on the tungsten. The recrystallization temperature was determined as above. Third, the nickel-induced recrystallization process in doped wire was studied more closely by electroplating 8 mils of Ni on 65-mil alumina-silica doped tungsten wire, AW153-NS10, and exposing the wire to temperatures of llOO°, 1200°, or 1300°C for various times in a hydrogen atmosphere. A circular recrystallization front, 'Onsisting of equiaxed grains, developed at the periphery Of the coated tungsten wire, and the advance of this front into the fibrous interior was studied. These experiments employed relatively coarse 0.065 in. D wire because the 0.010 in. D wire recrystallized too quickly to permit observation of the pene-

Jan 1, 1969

By M. D. Everell

A study has been made of the relationships between grinding selection functions and physical properties of rocks, particularly the failure loads of irregular particles and the compressive and tensile strengths of large regular specimens. The rocks used were limestones of various structures and impurity contents, a carbonatite, and a high-purity crystallized calcite. The selection functions were obtained from carefully performed grinding experiments on selected narrow size ranges in various grinding machines-a laboratory batch ball mill, a Hard grove grindability machine, and a mill of the type suggested by Yang, Mempel, and Fuerstenau. The specific rates of breakage during milling and the failure loads of irregular specimens correlated well for the rocks studied. The testing of irregular particles is suggested as a means of predicting the behavior of commercial mills.

Jan 1, 1973

Jan 1, 1941

By Norman B. Pilling, George P. Halliwell

The effects of lead and tin up to maximum contents of about 0.1 per cent. each, in the presence of oxygen between 0.04 and 0.30 per cent., have been studied. Tin is retained efficiently in the oxidized condition, whereas lead is not. An approximate relation between the lead-oxygen and tin-oxygen contents is deduced which, if observed, permits the presence of these elements without detrimental effect. Excess of lead beyond this limit affects ductility and rolling properties adversely and an excess of tin correspondingly diminishes the conductivity. It is shown that copper carrying a combined lead and tin content of several hundredths per cent., yet fully equal in quality to electrolytic wirebar, may be produced under commercial conditions. Tin is not normally found in more than bare traces in current grades of American electrolytic copper, and lead is rarely found to more than a few thousandths per cent. In the electrolytic refining of copper these metals do not present great difficulty in separation and their presence in any considerable amount in copper that has been refined by this method need not be tolerated. On the other hand, the effect of these elements is not entirely academic, as a considerable tonnage of scrap copper liberally contaminated with them has been reclaimed by the fire-refining process into metal with a residual lead and tin content of several hundredths per cent., yet having excellent working properties and fully equal in quality to current grades of electrolytic wirebar. Such copper has been found entirely suitable for use in the manufacture of electrical apparatus. In the absence of oxygen, tin is known to depress the conductivity rapidly, and lead to impair ductility and the rolling properties, yet the effects of these metals on commercial grades of copper—i. e., copper containing from 0.03 to 0.10 per cent. of oxygen—apparently has not received systematic attention. Occasional reference is made to the fact that in the presence of oxygen lead may be tolerated, yet Addicks says,1 in regard to overpoling: "The unstable condition can be controlled by adding certain substances, notably lead, in small quantities, but as mere

Jan 1, 1926

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By G. W. Healy, W. D. Forgeng, N. R. Griffing

The liquidus surface of the C-Cr-Fe system to 1900°C has been mapped from carbon solubility and freezing point measurements, metallographic observations, and published data. In the graphite field, the surface drops precipitously to meet a slope descending from the Cr3C2-C join through the mixed carbide fields to a meandering eutectic valley; this flows from the Cr-C to the Fe-C edge. On the low-cavbon side of the valley, the surface rises to the chromium corner. 1 HE purpose of this inquiry was to gain a more complete knowledge of the C-Cr-Fe liquidus surface. This required an extensive study of carbon and chromium-rich alloys which, in the past, have received the least attention. Sanbongi el al.1 measured the solubility of carbon in liquid alloys containing up to 25 wt pct Cr at temperatures of 1460" and 1545°C and found that it increased with chromium content and temperature. Lucas and wentrup2 also made solubility experiments in graphite crucibles, but at higher chromium contents in the range of 38 to 80 pct and at temperatures of 1550" to 1700°C; however, their experiments were relatively few, and the effect of temperature was not consistent. The present investigation included compsitions ranging from 0 to 94 pct Cr and 1.4 to 11.7 pct C at temperatures up to 1800°C. Saturation experiments in graphite crucibles, thermal analyses during freezing, and metallographic and X-ray diffraction studies were employed to obtain desired information which, together with published data from other investigations about the binary edges and the ternary system at lower carbon levels, made possible the construction of a comprehensive C-Cr-Fe liquidus surface. C-CR-FE LIQUIDUS SURFACE The derived ternary liquidus surface is shown in Fig. 1 where the solid curves are liquidus isotherms. The dashed curves and the binary edges are the liquidus field boundaries of the primary crystals, the arrows along these boundaries indicating their direction with decreasing temperature. Each intersection of three internal boundaries is the composition of liquid involved in four-phase isothermal equilibrium with the three primary crystals whose liquidus fields touch there. It may be observed that a total of six four-phase equilibria occur at melt temperatures. The general topography of the liquidus surface consists of a eutectic valley sloping down from the Cr-C edge at 3.2 pct C to the Fe-C edge at 4.25 pct C. The liquidus surface rises in two directions from the valley, one hillside terminating at the Cr-Fe edge while the opposing hillside rises toward the carbon corner out beyond the top edge of Fig. 1. Both hillsides are interrupted by intersections of surfaces or joints representing the liquid colmpositions of various three-phase equilibria. Seven primary crystals occur, namely a(bcc), ?(fcc), graphite, (Fe, Cr)3C capable of dissolving as much as 15 pct Cr, and three different chromium carbides in which iron is partially soluble by substitution for chromium. The composition ranges of the primary l~hases at melt temperatures are shown

Jan 1, 1962

By A. Aly Selim, Bruce D. Hanson

A computer model capable of simulating the basic production system in a variety of underground mining methods has been developed at the U.S. Bureau of Mines Twin Cities Mining Research Center. The simulation of the basic production system at the working face, which includes drilling, blasting, mucking, and roof bolting, is described in this paper. The model is event-oriented; that is, the status of the system is updated at the occurrence of an event. All event or activity times, including failure and repair of equipment, are treated as stochastic variables. A location dimension, in addition to the time dimension, is used, allowing the simulation of systems with a number of stopes or faces. To aid the user in determining the efficiency of his system, the model provides several reports. An event or activity report gives the frequency of occurrence, total active time, and cumulative delay statistics for each event. An equipment report delineates the availability and utilization of all equipment. A production report provides information on various performance measures such as tons produced and holes drilled. The cost report gives the cost of various elements in the system. Operating data from an actual mining situation were used in validating the model. In addition to the description of the model, examples of simulation experiments which were performed on a room-and-pillar mine system are given. Use of the model to determine methods for improving the efficiency of the system is discussed.

Jan 1, 1976

By W. D. Felix, R. D. Smith, J. A. Campbell

The mechanism most consistent with available information on atmospheric trace element emissions involves the volatilization of a significant fraction of many trace elements during coal combustion, with subsequent condensation on fly ash as the combustion gases cool. The larger surface-td-volume ratio of the smaller particles leads to an enrichment of the volatile trace elements. From an environmental viewpoint, the submicron size particles are of greatest concern. These particles show the highest concentrations of trace elements, are least efficiently collected by pollution control devices, have high atmospheric mobilities, and are deposited preferentially in the pulmonary and bronchial regions of the respiratory system. The mechanisms for trace element enrichment and formation of submicron particles will be described.

Jan 1, 1981

By B. Fitch

This paper deals with the behavior of sedimenting suspensions. More particularly, it treats, in as organized a manner as possible, the body of knowledge, theoretical or empirical, by which one predicts the behavior of miscellaneous swarms of particles in suspension. Such knowledge is necessary for precise and economical design of equipment. While the behavior of a single spherical particle settling through an infinite sea of quiescent fluid is well understood, practical sedimentation processes are almost always concerned with particles of assorted sizes, densities, and shapes, in such concentration that there is profound particle interaction. Such swarms of particles are observed to settle in any of four markedly different manners. Which one they follow is governed by particle interaction. It is determined largely by the dilution of the suspension, and the relative tendency of the particles to cohere. TYPES OF SEDIMENTATION The relationship between the different modes of sedimentation is shown paragenetically in Fig. 1. The left side of the diagram represents particles having little tendency to cohere; the right side represents particles for which interparticle cohesion is large compared to the settling force. The vertical axis represents dilution. As seen in the diagram, sedimentation is divided into three broad fields or regimes. At high dilutions there exists a regime here named 'clarification.' Particles in clarification may settle either individually, or by collecting into separated floccules. Thus there are two different possible modes of settling in the clarification regime. It is characteristic c~f this regime that there will be no clear line of demarcation between settling suspension and a supernatant. Faster particles settle out ahead of slower ones. In batch tests there develops a gradation of both particle sizes and pulp density due to progressive depletion of the largest particles from any given pulp level.

Jan 1, 1962

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers' determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By F. V. Shallcross

Physical properties of thin films of CdS and CdSe formed by vacuum deposition onto glass sibstrates have been studied as a function of deposition and processing conditions. The crystallinity and surface features of CdS films were examined using electron microscopy and electron and X-ray diffraction techniques. The films were poly crystalline; the preferred orientation and crystallite size increased with film thickness, substrate temperature, and deposition time. The CdS films consisted primarily of hexagonal-phase material, in contrast to similarly prepared CdSe films which have previously been observed to contain mixtures of cubic and hexagonal phases. As-deposited CdS films showed no major dependence of Hall mobility on crystallite size or degree of preferred orientation. Hall mobility and carrier concentration in CdS and CdSe .films were measured at various temperatures; both parameters increased with temperature and yielded activation energies which depended on fabrication conditions. Surface-desorption phenomena and overcoating of the semiconductor with SiO affected the observed electrical properties significantly. THIN films of cadmium sulfide1,2 and cadmium sele-nide3,4 have been employed by various workers as semiconductors in the insulated-gate thin-film field-effect transistor, known as the TFT. These devices are most commonly made by vacuum deposition of all materials onto an amorphous substrate such as glass. A knowledge of the microstructure and electrical properties of semiconductor layers used in the thin-film transistor is essential in order to form a realistic model for the device and to improve its performance, reproducibility, and reliability. This paper will describe studies of the physical properties of vacuum-deposited CdS and CdSe films prepared under various conditions. Structural characteristics examined in- cluded phases present, crystallite size, nature of preferred orientation of crystallites, surface roughness, and structural homogeneity throughout the film thickness. Electrical properties measured were Hall mobility and conductivity and their dependence on temperature and ambient. Thin-film properties are affected by many fabrication parameters including purity and physical form of evaporant, deposition rate, film thickness, design and temperature of the evaporation crucible, geometry of the deposition chamber, nature of the residual atmosphere, composition and temperature of the substrate, and details of postdeposition processing. PREPARATION OF FILMS In this work the semiconductor films were deposited in a conventional oil-diffusion-pumped system with pressures in the 10-8 torr range. The CdS evaporant was obtained from the Eagle-Picher Co. as a high-purity coarse-grained crystalline powder; the CdSe was a high-purity sintered powder supplied by the Harshaw Chemical Co. The evaporation crucible was a resistance-heated molybdenum-wire basket coated with aluminum oxide and filled with a quartz wool plug at the top. The source to substrate distance was usually 10 cm. This region was enclosed by a Pyrex inner cylinder. The substrate was heated with an overlying Pyrex plate coated with tin oxide. The substrate temperature was controlled using a thermocouple attached to the lower side of the heater. This thermocouple was calibrated against another thermocouple attached to a dummy substrate and by observation of melting points of various metal films deposited in the system. The substrates were polished borosilicate glass plates and conventional glass microscope slides. Substrate preparation included cleaning with an ultrasonically agitated detergent bath followed by isopropanol-vapor de-greasing. Film thickness was measured interferomet-rically during and after deposition. STRUCTURE OF CdS FILMS Structural studies were performed on CdS films using electron diffraction, electron microscopy, and

Jan 1, 1967

By C. H. Mathewson

MicrOscopic metallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent rnicrostructural rnosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atoms or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientatjions and it is always possible to derive one from the other by some form of- rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

Jan 1, 1928

By Ian Wark

IT has been shown1 that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "stand-ard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,' it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator.

Jan 1, 1939

By Joseph B. Story, John T. Clarke

A modification, of the Kelvin bridge using an inductor was used to measure the conductivities of molten sodium chloride, calcium chloride, and mixtures thereof. A capillary-type four-lead fused quartz dipping cell was constructed. The effect of a small amount of potassium chloride on the conductivity of the melt was determined. IN the electrowinning of sodium and chlorine from sodium chloride in Downs cells, calcium chloride is added to the sodium chloride in an approximately equimolar amount to permit cell operation at a lower temperature. This lower temperature improves current efficiency and ease of operation, but decreases voltage efficiency by decreasing the electrical conductivity of the melt. A knowledge of the electrical conductivity of the Downs cell melt is necessary to the understanding of Downs cell operation, for the IR voltage drop across the melt is responsible for a significant part of the electrical power consumed by the cell. The work of previous investigators on fused sodium chloride-calcium chloride mixtures was reviewed from the standpoint of consistency with the results of others on the conductivities of the pure constituents. The electrical conductivity of pure fused sodium chloride has been established with accuracy by Van Artsdalen and Yaffe,1 by Edwards, Taylor, Russell, and Maranville,2 and by Lee and Pearson.3 It has also been studied by a number of other investigators.4-13 The best values for calcium chloride are believed to be those of Lee and Pearson,3 since the sodium chloride and potassium chloride conductivity values given by them check the best literature values. A number of other investigators have also reported values for calcium chloride.'-"."' Electrical conductivity data for fused sodium chloride-calcium chloride mixtures have been reported by Sandonnini,12 Vereshchetina and Luz-hnaya,18 Ryschkewitsch,11 Barzakovskii,5 and Alaby-shev and Kulakovskaya.15 Sandonnini reports no data at temperatures lower than 850°C. The conductivity values reported by Vereshchetina and Luz-hnaya, by Ryschkewitsch, and by Barzakovskii for pure sodium chloride and for pure calcium chlor- ide vary somewhat from the literature values believed to be best and the sodium chloride-calcium mixture data of these authors and of Alabyshev and Kulakovskaya (who give no data for the pure compounds) show significant variations. In view of these facts, it seemed that an investigation of the electrical conductivities of fused sodium chloride-calcium mixtures would be worthwhile. Apparatus Bridge System—The bridge used,in this investigation is diagrammed in Fig. 1. In general, the elaborations of this bridge over the simple Wheatstone bridge were for the purposes of a) eliminating lead resistances or making them accurately measurable, and b) eliminating major capacitative and inductive effects or balancing them against each other. Lead resistances in the lower arms of the bridge were kept as low as possible by making the leads short and of low resistance wire. This could not be done in the cell arm of the bridge because of the remoteness of the cell from the other bridge components and because of the high-resistance nickel or chrome1 wires used in the cell. Since maximum sensitivity is attained when the resistances of the four arms of the bridge are equal, 50-O resistors were used in the lower arms of the bridge when fused salt conductivities were being measured, and 1000-O resistors were used when the cell was being calibrated with normal aqueous KCl solution. The cell resistance was of the order of 50 ohms with fused salts and of the order of 1000 ohms with normal aqueous KC1 solution. The resistors used were non-inductive and accurate to 50.05 pct (General Radio Co. Types 500-C and 500-H). The lead resistance between point A in the cell and point E at the measuring resistor was eliminated by using the kelvin bridge principle; that is, the voltape drop across the lead from point A to point E was divided between the cell arm of the bridge and the measuring arm of the bridge in proporation to the resistaxes in the lower arms of the bridge.

Jan 1, 1958

W. H. BASSETT,* Waterbury, Conn. (written discussion ?).-The effect of reducing gases on hot solid copper has been known for many years in the copper industry, and precautions taken to guard against it in the general practice in copper heating and annealing. In view of the statement that Bengough and Hill, in 1910, were the first to suggest the possibility of the formation of gas within the copper itself, it is interesting to note that in Harper's Magazine for April, 1904, an article, "Life and Diseases of Metals," by Professor Heyn, illustrated the effect of reducing gases on copper by a photograph, which is shown in Fig. 1. This he entitled "Copper burst asunder by disease." After referring to the effect of hydrogen on steel, he makes the following remark: "Similar symptoms of poisoning, caused by hydrogen or gases containing hydrogen (as gas for lighting purposes), are apparent in copper when exposed to red heat. Not every kind of .copper is susceptible to this poisoning in equal degree. Copper per-fectly free of cuprous oxide is entirely exempt from poisoning. Most of the various coppers of commerce, however, contain cuprous oxide, formed during the smelting process while exposed to atmospheric influences. In such coppers, containing cuprous oxide, hydrogen causes a terrible disease on the copper being heated red hot. The copper bursts asunder and is permeated by cracks. This disease is practically incurable and can be eradicated by resmelting only. The results work destructively according to the amount of cuprous oxide contained in the copper." It must have been evident to Professor Heyn, as it was to us on reading this article, that the bursting asunder of the copper was clue to the formation of steam. Practical copper heaters have known for many years that it was quite possible to produce blisters, or large gas holes, in the interior of copper plates or bars by heating to a high temperature in reducing gases. These facts, of course, do not detract from the value of the study of the action of hydrogen gas that has been made by Mr. Pilling, but simply illustrate that the practical effect of reducing gases on furnace-refined copper has long been a troublesome factor in the heating or annealing of that metal.

Jan 1, 1919

By Tell Ertl, Ernest E. Burgh

INTRODUCTION THE Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose-that of finding out how to mine oil shale most cheaply-entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, factors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing. When the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. PROCEDURE Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 1 ¼ in. in diameter was used in 6, 12, and 18 ft lengths with 2 1/8 -in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton. During the experiments air pressure varied between 75 and 90 psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings To facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-steel sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a 1-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1947

P. W. SHIMER, Easton, Pa. (written discussion*).-When lump calcium cyanamid is immersed in the melt of mixed chlorides of the alkalies and alkaline earths in the manner described in the paper, the amount of sodium cyanide formed in the melt, as shown by numerous analyses, is but a small fraction of that formed by the reaction referred to by Mr. Johnson. The case-hardening effects in my process are, however, at least as good as when the common cyanide baths are used. Moreover, when compared with the cyanide baths, the gases evolved in the new process are harmless, consisting of nitrogen, carbon monoxide (which burns to carbon dioxide on the surface of the melt), and occasionally a little carbon dioxide. These gases are not irritating or poisonous, whereas the vapors arising from cyanide baths are both irritating and poisonous. The complex chemical reactions that take place in and on the surface of the melt are being investigated by the writer, who hopes, in due time, to communicate the results of his work.

Jan 7, 1919