Search Documents

By B. Woyski

MANY writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deoxidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gases is more difficult to overcome. The regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes are the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer' lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere.

Jan 5, 1922

By H. K. Work, G. H. Enzian

In the manufacture of steel for commercial purposes, the deoxidation practice used, i.e., the method and degree of deoxidation, is an important factor affecting the structure and mechanical properties of the finished steel. Deoxidation practice exerts a pronounced influence not only on the soundness of the ingots but also on the reaction of the steel to a number of mechanical and thermal treatments. The first mentioned effect of deoxidation is more or less obvious and was first demonstrated, though perhaps not fully appreciated, by Robert Mushet when, in 1856, he added speigeleisen to low-carbon bessemer blown metal. In 1861. Bessemer patented the addition of one pound per ton of silicon to his blown metal to "cause the metal to lie quietly in the mold." The second effect of deoxidation-—that is, the effect on the properties and behavior of the steel—is, one might say, more subtle, and certainly not as well understood as the first, although in many cases it is the more important consideration. This paper is limited to a discussion of only the second effect of deoxidation and: in particular, to the effect on the strain-sensitivity of low-carbon steels. General Discussion Originally it was thought that the function of a deoxidizer was to combine with the oxygen present in the steel as iron oxide and prevent its subsequent evolution as a gas. -More recently it has been realized that a deoxidizer does more than this. Frequent reference has been made to the effect of deoxidizers on the nitrogen in the steel, and some attention has also been paid to hydrogen. As a consequence of the above situation any study of deoxidation must be concerned with the gas content of the steel and the effect of the deoxidizer on the gases involved. The term "gas content" as used here refers to gases extracted from steel during melting in vacuum rather than to elements present in steel in the gaseous state. The extracted gases, at least in the case of oxygen and nitrogen, are generally accepted to be products of decomposition of oxides, nitrides, or other more complex compounds. The manner in which deoxidation affects the gas content of steel and the significance of gases in steel have been and still are subjects of considerable speculation. No attempt will be made here to give a complete discussion of the literature on this subject but a few references will be cited for purposes of illustration. N. Hamilton1 found a correlation between the oxygen content of alloy steel and the behavior of the steel during tube piercing. Davenport, Bain, and others associated oxygen with aging properties of steel while Köster5 and a number of others6-lo made similar claims for nitrogen. Daniloff, Mehl, and Hertyll stated that "deoxidation decreases the susceptibility of steels to aging directly

Jan 1, 1945

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By J. R. Cain

In every process for making steel there are one or more stages where the metal is exposed to gas of one kind or another. Thus, in the open-hearth furnace, the carbon dioxide and water vapor in the products of combustion are oxidizing toward the ferrous and manganous oxides in the slag, tending to convert these to higher oxides; the higher oxides then , oxidize the steel, so that indirectly the products of combustion are oxidizing toward the steel. In the Bessemer process, there is direct contact of air and steel; also, the water vapor in the air blown into the converter is continually decomposed by the molten steel, yielding hydrogen and ferrous oxide, both of which are in part taken up by the metal. In the electric-furnace processes, there is always more or less air in contact with the slag covering the metal, and this air and the gaseous reaction products from it are dissolved in the slag to some extent and thus transmitted in part to the steel. In the crucible processes, there is always entrapped air in the charges and the crucibles are more or less permeable to the gaseous products of combustion from the furnace. In all the processes of manufacture, the molten metal is exposed to air while tapping into ladles and ingot molds and has an opportunity to saturate itself with air or with gaseous or solid products generated by chemical reactions between air and steel. Sievertsl has shown that molten metals requirc but a few seconds to saturate themselves with a surrounding gas. No one familiar with the operations at a steel plant needs to be reminded of the important role that gases play at all stages. The familiar "boil" of open-hearth furnaces, due to evolution of carbon monoxide when iron ore is added to the molten steel; the spectacular operation of the Bessemer converter brought about entirely by a gaseous reagent; the almost magic effect of small quantities of silicon, manganese, or aluminum added to the molten metal in ladle or furnace in quickly preventing bubbling and evolution of gases; the unwelcome phenomena of blowholes in ingots that have not been properly manufactured—these

Jan 1, 1920

By Albert Sauveur

This paper explains the possibility of using advantageously a boiling solution of sodium picrate to reveal dendritic segregation in steel. The mechanism of the action of the reagent is described. The failure of manganese alone to produce persistent dendritic segregation is also considered. IRON, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.1 For this purpose, a cupric solution, such as Le Chatelier's, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free., from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters, which represents the same spot as that shown in Fig. 1. The fillings

Jan 2, 1924

By Walter Nummela

INTRODUCTION By the end of 1979 pellet productive capacity from the processing of low grade iron ores in the Lake Superior-District will total 86 million tons per year. Of that tonnage, 72 million result from the processing of magnetic ores such as taconite, about 6 million tons from the flotation processing of relatively coarse grained specular hematite, and 8 million tons from the processing of fine grained non- magnetic ores at Tilden. The Tilden flowsheet represents a break- through in the processing of this type of crude ore and hence is unique in the Lake Superior District (1). Operations at Tilden started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleve- land-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling- Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Other companies have conducted extensive pilot plant tests or are in commercial production in the processing of fine grained non-magnetic ore materials (2). Flowsheets and reagent schedules may be different for each particular application, but some of the problem areas in the processing of Tilden ores have also been experienced at operations such as the IOC Plant at Sept-Isles, at Lamco and at Bong in Liberia, and in pilot testing of Fabrica ores of Ferteco Mineracao in Brazil. With a grind of about 80-85% -500 mesh resulting in 50% of the particles in the concentrate being less than 15 microns, a discussion of the pro- cessing of Tilden type ores fits the topic of this workshop. There are very large tonnages of fine grained non-magnetic crude ores which exist throughout the Lake Superior District and other iron ore producing regions. These fine grained non-magnetic materials constitute an important source of iron minerals. Before going into specifics of the flowsheet, it is important to

Jan 1, 1979

By Yves Dardel

INTRODUCTION SINCE the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts,2 then Baukloh and Oesterlen,3 during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreau,4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per 100 g of metal. Winterhager,5 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitz6 as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhauser8 extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per 100 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per 100 g, while that of the usual apparatus was only about 0.2 cm3 per 100 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. [ ] Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of Eborall and Ransley, as well as the earlier apparatus,

Jan 1, 1948

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used. Together with 4 pct gypsum to retard setting time, the kiln run clinker—consisting of hard, semi-fused lumps that may have been crushed to — 1/2 in.—is ground to a Blaine surface area of 3000 sq cm per gram and about 92 pct passing 325 mesh. Approximately 32 kw-hr per ton, or 6 kw-hr per 376-1b barrel, are consumed in the grinding mills alone, not counting auxiliaries. Open Circuit Clinker Grinding: Many early clinker grinding plants employed two-stage, open circuit grinding. Comparatively short mills of large diameter, loaded with balls 4 in. and smaller, first reduced the clinker to 95 pct passing 14 mesh. Tube mills of smaller diameter and greater length, loaded with balls 11/4 in. and smaller, carried out the fine grinding operation. An early development was to assemble two or more stages of grinding in a single mill having two, three, or four compartments separated by division heads. There were difficulties in balancing the compartments, but compartment mills were popular in the 1920&apos;s because the layout was simple and there were no elevators and conveyors. Oversize Particles: Open circuit mills, whether separate ball and tube mills or compartment mills, always encountered the problem of tramp oversize in the product. A small percentage of clinker survived passage through the first grinding stage as particles—perhaps 1/16 in. diam—that were too large for the smaller balls in the following stages to reduce to —200 mesh. When the feed rate was lowered to reduce tramp oversize, there were serious losses in grinding efficiency. Many ingenious designs were perfected to incorporate perforated screen plates or wire mesh screens in the ball mills or in the first compartments of compartment mills. Their purpose was to prevent mate: rial passing out of the first stage until it was small

Jan 1, 1958

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By Otto H. Henry, J. J. Cordiano

THOUGH powder metallurgy is one of the oldest of metallurgical processes, it is in its infancy as a branch of the modern field of metallurgy. As early as 3000 B.C., the ancients produced implements and weapons of iron by reducing iron ore in a charcoal fire and forging the resultant sponge while still hot into the desired shape. Melting and casting soon superseded the powder metallurgy practice, and it was not until the turn of the twentieth century that powder metallurgy was applied to the commercial manufacture of tungsten lamp filaments. From this beginning, the use of the powder metallurgy process spread to the manufacture of porous oil-impregnated bearings, cemented carbide tools, contact points, diamond grinding wheels, clutch facings, starter brushes, resin-bonded radio cores, magnets, metallic filters, and other parts. More recently, and particularly during the present war, there has been a definite trend toward the manufacture of machine parts by this process in competition with the more conventional fabricating methods. Notwithstanding these many developments, scientific progress has been slow. While many articles on powder metallurgy have appeared in the press and various publications, there have been too few contributions to our technical societies, with the result that there is a dearth of the type of information necessary for the full development of this science. It is of primary importance that the results of research and development be freely disseminated if powder metallurgy is to realize its fullest potentialities. PURPOSE OF INVESTIGATION Excluding the refractory metal field, all commercial powder metallurgical products made by a cold compressing and sintering operation contain voids. These voids can be substantially eliminated by subsequent severe working and heat-treatment, but such practice has not proved economical in most applications. By applying heat during the compressing operation, plastic deformation of the powder particles is substantially increased, and the resultant compact or briquette is practically free of voids. However, hot-pressing has many attendant problems, which at present preclude its use in the manufacture of precision parts. The more important of these are to devise: I. A die steel capable of withstanding high pressures at elevated temperatures. 2. A high-temperature lubricant capable of preventing excessive die wear and welding of the compact to the die walls. 3. A method of retaining a neutral or reducing atmosphere in the compacting zone of the die assembly. 4. A means of ejecting the hot-pressed specimen into a neutral atmosphere until reasonably cold.

Jan 1, 1945

By J. A. Church

I. Early Furnaces,......423 11. Experiments with the HIgh-Shaft FURnace,..... 426 III. ExperMents wIth the Wide FURnace,..429 IV. ExperEentS with Extreme BOSH,... 43.2 V. Survival of the 56 by 180 IN. Furnace,.434 VI. Recent ExpeEiments,.....436 VII. SUMMary,........438 I. Early Furnaces. Copper blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in.; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 1, 1914

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By F. L. Wolf, G. E. Alderson

The reclaiming of nietallics from slag and sweepings is of vital interest to every brass-foundry man, but the first cost and interest on the investment often make it prohibitive for the small foundry to enjoy the benefits of a complete concentrating unit. However, the cost of such an installation and the cost of operation are often exaggerated to such an extent that foundries dispose of their copper-bearing refuse at a great loss. This paper gives the actual costs and the returns obtained in the reclaiming plant used at the Ohio Brass Co. This plant is divided into two sections—the preliminary treatment and concentrating departments. In the former occur the screening, crushing, and hand-picking operations whereby rnost of the non-valuable and heavy metallic constituents are removed. The concentrating equipment consists of an elevator, bins, jigs, ball-mill, arid table. Preliminary Treatment The preliminary treatment varies, depending on whether the material is slag, foundry-floor sweepings, or brass casting-floor sweepings. Material of the first class is produced from the operation of six Steele-Harvey and six Schwartz furnaces; the second class represents sweepings from an average of thirty-five. molding floors per day: and the last is collected around the sprue cutters and knockout bench. Treatment of Slag The slag, analyzing 30 to 40 per cent. copper, is passed over a 3-mesh yard screen (Tyler standard mesh) stretched on an inclined rectangular frame supported by adjustable legs and equipped with a hopper which directs the undersize into a barrow. The fine product, running about 20 per cent. copper and representing 20 to 25 per cent. of the total slag, goes direct to a storage bin for concentrator frrd. The oversize is charged into a No. 2 Hill cinder crusher, which takes 175 to 200 11,. to a charge and crushes two charges per hour through &apos;a No. 4 riddle. It

Jan 1, 1921

By Dell H. Adams

COAL EXPLORATION Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining. PHASES OF EXPLORATION The high capital risks of coal exploration and land acquisition dictate that a multiphase program be utilized to minimize initial risk. In such a program, phased development of the data insures that each increase in capital expenditures will be justified by a corresponding increase in the level of confidence in the ultimate success of the project. Each phase is designed to provide sufficient data and property control to facilitate the decision whether to proceed to the next phase of development or to discontinue the program (Table 1). The first phase of a typical exploration program consists of a pre-

Jan 1, 1981

By E. V. Daveler

THE milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. CHARACTER OF ORE The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver 0.10 oz. Magnesia 0.4 per cent. Silica 59.7 per cent. Sulfur 1.2 per cent. Iron 5.2 per cent. Lead 0.1 per cent. Alumina 21.4 per cent. Zinc 0.2 per cent. Lime 5.0 per cent.

Jan 1, 1920

By Arthur Baker III

The orebodies are long bedding-plane lenses of chalcopyrite and sphalerite, associated with garnetite masses. Most of the orebodies are within a 50-ft thickness of Cambrian limestone; other Paleozoic limestones and dolomites are locally metamorphosed but only slightly mineralized. Pre-mineral faults are numerous, but shallow folds were the main ore-localizing structures. JOHNSON camp is in the northwestern part of Cochise County, Ariz., about 50 miles east of Tucson. The nearest major mining districts are Tombstone and Bisbee, respectively 27 and 50 miles to the south, and the Superior-Miami-Globe-Ray porphyry copper group, about 90 miles northwest. Like many mining camps of the Southwest, Johnson camp is said to have been worked by the Spaniards. The first production on record was in the early 1880&apos;s, when an unknown amount of oxidized copper-silver ore in the Peabody mine was mined from replacement orebodies in the Pennsyl-vanian Naco formation. From 1904 to 1911 outcropping oxidized ores in the Cambrian Abrigo formation were worked, and an estimated 100,000 tons of copper ore were shipped. In 1912 the first large sulphide orebody of the district, the Republic Manto orebody, was discovered, and in the following few years some 250,000 tons of predominantly sulphide ore were shipped. The average grade of this ore was approximately 4.5 pct Cu, 6 pct Zn, 0.8 oz. Ag, and 0.001 oz Au. The Republic, Copper Chief, and Mammoth mines were the principal producers during this period. Mining ceased in the district after 1920, and until 1943 only small-scale leasing operations were carried on. In 1943 all the mines that had been productive were acquired by the Coronado Copper and Zinc Co., the present operators, and in the 10 years since that time the district production has amounted to approximately 350,000 tons of milling ore averaging 2 pct Cu and 6 pct Zn. Most of this ore was produced from the Republic and Mammoth mines, but since 1950 a large part of the production has been from the new Moore mine. The total known production from the district, then, is about 3/4 million tons of copper and copper-zinc ore of low grade. All of this ore was produced from orebodies associated with garnetite in the middle member of the Cambrian Abrigo formation. In addition to this known production, an unknown tonnage of ore was extracted from the Peabody mine orebodies that lie in the Pennsylvanian Naco formation. Published information on the geology of the district is limited. Aside from brief references in various mining journals, only three papers on the district have been published.1-3 One of these is a U. S. Bureau of Mines report on a diamond drilling program, one is a brief paper on the general geology of the district, and the third is a report on geochemical experiments, with a section on the occurrence of the orebodies. The last two are by John Cooper, of the United States Geological Survey, who has done much detailed work in the area. Stratigraphy The rocks of the mineralized area are Paleozoic sediments ranging in age from Cambrian to Penn-sylvanian. Several disconformities are present in the stratigraphic column, the most important one being between the Cambrian Abrigo formation and the Devonian Martin formation. There are no angular unconformities. Within the district, the Paleozoic sediments lie in a fairly uniform monocline, striking northwest and dipping 30" to 50" northeast. This local monocline is part of a domal struc-ture centered in the Little Dragoon mountains to the southwest. The Texas Canyon stock, a quartz monzonite body intruded probably during the Laramide revolution, lies south of the mineralized area (Ref. 2, p. 33). The Paleozoic rocks dip away from the stock, and on the surface are separated from it by at least 1500 ft of Pre-Cambrian rocks. The outcrop pattern of the northeastern edge of the stock suggests that it may dip gently northeastward, passing below the mineralized area at moderate depth. No quartz monzonite has been found in mine workings or diamond drill holes, which reach to depths of 1000 ft. The only igneous rock found in the mineralized area is a lamprophyre dike cutting the Naco limestone in and near workings of the Peabody mine. With the exception of the lowermost beds—the Bolsa quartzite and the shaly lower member of the Abrigo formation—the Paleozoic sediments are predominantly carbonate rocks, Fig. 1. The middle member of the Abrigo formation, which contains the principal ore-bearing beds, is limestone, with thin shale partings throughout most of its 250-ft thick-ness. Near the top of this member is a sandy bed some 25 ft thick. The upper member of the Abrigo formation and the lower half of the overlying Devonian Martin formation are dolomitic, with num-

Jan 1, 1954

By Erwin Pink

It has been pointed out in a previous publication&apos; that, for a given strain rate, serrated yielding can be observed only at certain test temperatures. Fig. 1 shows the results obtained for polycrystalline and re-crystallized tantalum, Va group in the periodic table of elements, where serrations in the course of deformation match the decrease of total elongation. However, there was no evidence of repeated yielding when testing molybdenum or tungsten, VIa group, at similar conditions, i.e., annealed and air-cooled samples (serrations have been found in quenched tungsten2). The reason for the observed serrations in the stress-strain curve are dissolved impurities on interstitial sites of the lattice. Of importance is the concentration of oxygen, carbon, and nitrogen, which are in random solution. Two methods to calculate the limiting concentrations for serrated yielding have been evaluated and applied with more or less success in estimating the role of carbon and nitrogen in mild steel.3 J. Friedel4 has given two equations, which determine the upper and lower strain rates i for the appearance of serrations at a certain test temperature: W denotes the binding energy of the interstitial atom, -1 ev for refractory metals;5 e&apos; the portion of continuous strain in the discontinuous stress-strain curve, measured as -3x10-3; b the Burgers vector, c the concentration, see Table 11, in atom fractions; p the dislocation density, -2 X l09 per cm2 at an average stress ?, -15 kp per mm2 at medium strain. k stands for the Boltzmann constant, T for the absolute temperature, and D for the diffusion coefficient. Table I. Eq. [1], for a given strain rate, determines the minimum temperature, and [2] the maximum temperature, below or above which no "dynamic strain-aging" can occur. According to the calculation, which uses the given quantities, serrations should only be observed within the cross-hatched temperature regions in Fig. 1, and this is in good agreement with the experiment. The effect of varying impurity concentrations is indicated schematically in Fig. 2: only Eq. [I] is affected. Setting Eq. [I] equal to [2], one can calculate the limiting concentration cmin which first causes serrations. The second method uses the aging condition by Cottrell and Bilby6,7 \£i/ \ n. a / where n(t) is the number of impurity atoms, which segregate at a dislocation line of 1 cm length after the time t (t in our case is the time between "repeated yield drops" in the serrated curve, or, the time until the above mentioned strain E&apos; is obtained, i.e., -1 sec for medium intensity or serrations). no is the number of impurity atoms in 1 cm3 and A = Qb4ep[(1 + v)/(l - v)], derived from equations given in Ref. 7. p is the shear modulus, 18,800 kp per mm2 for tantalum, 12,200 for molybdenum, AE the tetragonal distortion caused by interstitial impurities in a bcc lattice (approximately 0.4 for both tantalum and molybdenum) and v Poisson&apos;s ratio (0.35 for tantalum, 0.30 for molybdenum). From Eq. [3], combined with the condition for a pronounced yield drop as formulated by cottrel16 (at least one impurity atom segregated at the unit length of a dislocation), again a no min, and hence the concentration Cmin can be calculated.

Jan 1, 1970

By A. L., Bailey

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally.

Jan 1, 1949